scholarly journals The Influence of Thickness on the Tensile Strength of Finnish Birch Veneers under Varying Load Angles

Forests ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 87
Author(s):  
Maximilian Pramreiter ◽  
Alexander Stadlmann ◽  
Christian Huber ◽  
Johannes Konnerth ◽  
Peter Halbauer ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Size Effect ◽  
High Performance ◽  
Mechanical Performance ◽  
Solid Wood ◽  
Strengthening Effect ◽  
Wood Composites ◽  
Design Flexibility ◽  
Wood Part ◽  
Load Angle

The development of high-performance, veneer-based wood composites is a topic of increasing importance due to the high design flexibility and the comparable mechanical performance to solid wood. Part of this improved mechanical performance can be contributed to the size effect present in wood. Based on previous findings in the literature, this size effect can be either strengthening or weakening. The presented study investigates the influence of thickness and load angle on the tensile strength and tensile stiffness of peeled veneers compared to thin sawn timber. Veneers with thicknesses of 0.5 ± 0.05 mm, 1.0 ± 0.05 mm and 1.5 ± 0.05 mm as well as sawn wood with thicknesses of 1.5 ± 0.1 mm, 3.0 ± 0.1 mm and 5.0 ± 0.1 mm were tested in tension under different load angles (0°, 45° and 90°). The results only partly confirm a size effect for strength parallel to the grain. The strength perpendicular to the grain increased significantly between 0.5 mm and 1.5 mm, with a significant decrease between 1.5 mm and 5.0 mm. The presence of lathe checks diminished the strength perpendicular to the grain of the veneers by about 70% compared to solid wood, partly overshadowing a possible strengthening effect. It was concluded that a transition from a strengthening to a weakening behaviour lies in the range of multiple millimetres, but further investigations are needed to quantify this zone more precisely. The presented results provide a useful basis for the development of veneer-based wood composites with a performance driven layer-thickness.

Influence of Sintering Parameters on the Mechanical Performance of PM Steels Pre-Alloyed with Chromium

2007 ◽  
Vol 534-536 ◽  
pp. 545-548 ◽  
Author(s):  
Ola Bergman ◽  
Björn Lindqvist ◽  
Sven Bengtsson
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
High Performance ◽  
Mechanical Performance ◽  
Sintering Temperature ◽  
Oxide Reduction ◽  
Low Oxygen ◽  
Positive Effects ◽  
Partial Pressures

Powder grades pre-alloyed with 1.5-3 wt% chromium are suitable for PM steel components in high performance applications. These materials can be successfully sintered at the conventional temperature 1120 °C, although well-monitored sintering atmospheres with low oxygen partial pressures (<10-17-10-18 atm) are required to avoid oxidation. Mechanical properties of the Cralloyed PM grades are enhanced by a higher sintering temperature in the range 1120-1250 °C, due to positive effects from pore rounding, increased density and more effective oxide reduction. A material consisting of Astaloy CrM, which is pre-alloyed with 3 wt% Cr and 0.5 wt% Mo, and 0.6 wt% graphite obtains an ultimate tensile strength of 1470 MPa combined with an impact strength of 31 J at density 7.1 g/cm3, after sintering at 1250 °C followed by cooling at 2.5 °C/s and tempering.

scholarly journals Synchronously Strengthen and Toughen Polypropylene Using Tartaric Acid-Modified Nano-CaCO3

Nanomaterials ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 2493
Author(s):  
Junlong Yao ◽  
Hanchao Hu ◽  
Zhengguang Sun ◽  
Yucong Wang ◽  
Huabo Huang ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Impact Toughness ◽  
Tartaric Acid ◽  
High Performance ◽  
Mechanical Performance ◽  
Low Cost ◽  
Complexing Agent ◽  
Environmental Technology ◽  
The Impact ◽  
First Time

In order to overcome the challenge of synchronously strengthening and toughening polypropylene (PP) with a low-cost and environmental technology, CaCO3 (CC) nanoparticles are modified by tartaric acid (TA), a kind of food-grade complexing agent, and used as nanofillers for the first time. The evaluation of mechanical performance showed that, with 20 wt.% TA-modified CC (TAMCC), the impact toughness and tensile strength of TAMCC/PP were 120% and 14% more than those of neat PP, respectively. Even with 50 wt.% TAMCC, the impact toughness and tensile strength of TAMCC/PP were still superior to those of neat PP, which is attributable to the improved compatibility and dispersion of TAMCC in a PP matrix, and the better fluidity of TAMCC/PP nanocomposite. The strengthening and toughening mechanism of TAMCC for PP involves interfacial debonding between nanofillers and PP, and the decreased crystallinity of PP, but without the formation of β-PP. This article presents a new applicable method to modify CC inorganic fillers with a green modifier and promote their dispersion in PP. The obtained PP nanocomposite simultaneously achieved enhanced mechanical strength and impact toughness even with high content of nanofillers, highlighting bright perspective in high-performance, economical, and eco-friendly polymer-inorganic nanocomposites.

scholarly journals Mechanical and Fracture Parameters of Ultra-High Performance Fiber Reinforcement Concrete Cured via Steam and Water: Optimization of Binder Content

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2016
Author(s):  
Avan Ahmed Mala ◽  
Aryan Far H. Sherwani ◽  
Khaleel H. Younis ◽  
Rabar H. Faraj ◽  
Amir Mosavi
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Performance ◽  
Mechanical Performance ◽  
Binder Content ◽  
Splitting Tensile Strength ◽  
Steam Curing ◽  
Flexural Tensile Strength ◽  
High Performance Fiber ◽  
Curing Methods

An investigational study is conducted to examine the effects of different amounts of binders and curing methods on the mechanical behavior and ductility of Ultra-High Performance Fiber Reinforced Concretes (UHPFRCs) that contain 2% of Micro Steel Fiber (MSF). The aim is to find an optimum binder content for the UHPFRC mixes. The same water-to-binder ratio (w/b) of 0.12 was used for both water curing (WC) and steam curing (SC). Based on the curing methods, two series of eight mixes of UHPFRCs containing different binder contents ranging from 850 to 1200 kg/m3 with an increment of 50 kg/m3 were produced. Mechanical properties such as compressive strength, splitting tensile strength, static elastic module, flexural tensile strength and the ductility behavior were investigated. This study revealed that the mixture of 1150 kg/m3 binder content exhibited the highest values of the experimental results such as a compressive strength greater than 190 MPa, a splitting tensile strength greater than 12.5 MPa, and a modulus of elasticity higher than 45 GPa. The results also show that all of the improvements began to slightly decrease at 1200 kg/m3 of the binder content. On the other hand, it was concluded that SC resulted in higher mechanical performance and ductility behavior than WC.

scholarly journals Exploring Environmentally Friendly Biopolymer Material Effect on Soil Tensile and Compressive Behavior

2020 ◽  
Vol 17 (23) ◽  
pp. 9032
Author(s):  
Chunhui Chen ◽  
Zesen Peng ◽  
JiaYu Gu ◽  
Yaxiong Peng ◽  
Xiaoyang Huang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Tensile Strength ◽  
High Performance ◽  
Xanthan Gum ◽  
Strengthening Effect ◽  
Bond Parameter ◽  
Underlying Mechanisms ◽  
Direct Tensile ◽  
Direct Tensile Test ◽  
The Impact

The study of the high-performance of biopolymers and current eco-friendly have recently emerged. However, the micro-behavior and underlying mechanisms during the test are still unclear. In this study, we conducted experimental and numerical tests in parallel to investigate the impact of different xanthan gum biopolymer contents sand. Then, a numerical simulation of the direct tensile test under different tensile positions was carried out. The micro-characteristics of the biopolymer-treated sand were captured and analyzed by numerical simulations. The results indicate that the biopolymer can substantially increase the uniaxial compressive strength and tensile strength of the soil. The analysis of the microparameters demonstrates the increase in the contact bond parameter values with different biopolymer contents, and stronger bonding strength is provided with a higher biopolymer content from the microscale. The contact force and crack development during the test were visualized in the paper. In addition, a regression model for predicting the direct tensile strength under different tensile positions was established. The numerical simulation results explained the mechanical and fracture behavior of xanthan gum biopolymer stabilized sand under uniaxial compression, which provides a better understanding of the biopolymer strengthening effect.

scholarly journals Synthesis of High Performance Thiophene–Aromatic Polyesters from Bio-Sourced Organic Acids and Polysaccharide-Derived Diol: Characterization and Degradability Studies

Molecules ◽  
2022 ◽  
Vol 27 (1) ◽  
pp. 325
Author(s):  
Lesly Dasilva Wandji Djouonkep ◽  
Arnaud Kamdem Tamo ◽  
Ingo Doench ◽  
Naomie Beolle Songwe Selabi ◽  
Emmanuel Monga Ilunga ◽  
...  
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
Ethylene Terephthalate ◽  
Mechanical Performance ◽  
Structure Property ◽  
Weight Losses ◽  
Crystallization Ability ◽  
Poly Ethylene Terephthalate ◽  
Structure Property Relationship ◽  
Poly Ethylene

In this work, the feasibility of replacing petroleum-based poly(ethylene terephthalate) (PET) with fully bio-based copolyesters derived from dimethyl 2,5-thiophenedicarboxylate (DMTD), dimethyl 2,5-dimethoxyterephthalate (DMDMT), and polysaccharide-derived 1,6-hexanediol (HDO) was investigated. A systematic study of structure-property relationship revealed that the properties of these poly(thiophene–aromatic) copolyesters (PHS(20–90)) can be tailored by varying the ratio of diester monomers in the reaction, whereby an increase in DMTD content noticeably shortened the reaction time in the transesterification step due to its higher reactivity as compared with DMDMT. The copolyesters had weight-average molar masses (Mw) between 27,500 and 38,800 g/mol, and dispersity Đ of 2.0–2.5. The different polarity and stability of heterocyclic DMTD provided an efficient mean to tailor the crystallization ability of the copolyesters, which in turn affected the thermal and mechanical performance. The glass transition temperature (Tg) could be tuned from 70–100 °C, while the tensile strength was in a range of 23–80 MPa. The obtained results confirmed that the co-monomers were successfully inserted into the copolyester chains. As compared with commercial poly(ethylene terephthalate), the copolyesters displayed not only enhanced susceptibility to hydrolysis, but also appreciable biodegradability by lipases, with weight losses of up to 16% by weight after 28 weeks of incubation.

Yarn degradation during weaving process and its effect on the mechanical behaviours of 3D warp interlock p-aramid fabric for industrial applications

2020 ◽  
pp. 152808372093728 ◽  
Author(s):  
Mulat Alubel Abtew ◽  
François Boussu ◽  
Pascal Bruniaux ◽  
Carmen Loghin ◽  
Irina Cristian ◽  
...  
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
Mechanical Performance ◽  
Great Influence ◽  
Breaking Load ◽  
Industrial Applications ◽  
Warp Yarn ◽  
Fabric Architecture ◽  
Mechanical Performances ◽  
3D Warp Interlock Fabric

Three dimensional (3D) warp interlock fabric becomes a promising structure due to its good mechanical performances. However, its complex manufacturing process can cause severe yarn damage and affects its overall final performances. The current study addressed the effects weaving process and warp yarn ratios on the multi-filaments yarn degradations and its mechanical performances while 3D warp interlock fabric manufacturing. Four different 3D warp interlock variants having similar fabric architecture, and yarn densities but different warp yarns interchange ratios were manufactured using 930dTex high-performance multi-filament (Twaron® f1000). The multi-filaments yarns at different weaving processes were tested for their tensile properties. The results show that the average tensile strength of twisted yarns show a decrement of 5.68% as compared to the bobbin yarns. Meanwhile, warping process also showed a 16.11% maximum breaking load reduction as compared to the bobbin yarn. Besides, the tensile strength of binding yarn after weaving process for samples 3D-8/0, 3D-8/4, and 3D-8/8 was reduced by 12.79%, 5.22%, and 14.22% respectively as compared to the yarn after warping process. In conclusion, yarn degradation inside the 3D woven structure was affected not only by the various process parameters but also by the type of fabric architecture made with different warp yarn ratios. These phenomena ultimately bring a great influence both on the yarn and overall mechanical performance of the final products. For this, further studies are planned to investigate the multi-filaments yarn degradation effect on the ballistic performances fibrous material as it is directly linked to the yarn performance.

Influence of Silica Fume on High-Performance Concrete

2014 ◽  
Vol 670-671 ◽  
pp. 437-440 ◽  
Author(s):  
Fan Wang ◽  
Shan Suo Zheng ◽  
Xiao Fei Wang
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Split Tensile Strength ◽  
Binder Ratio ◽  
Water Binder Ratio

With the improvement of concrete materials and the emergence of new materials, adding silica fume to high-performance concrete (HPC) has been one of the important ways in concrete technology. In this paper, through experimental study on the mechanical performance of HPC with 5%, 10%, 15% and 20% silica fume replacing cement for different water-binder ratio, along with polycarboxylates high performance water-reducing admixture, silica fume has large effects on 28d compressive strength, split tensile strength and flexural strength of the HPC. Meanwhile, due to the different level of water-binder ratio, the relationship between split tensile strength, flexural strength and compressive strength is also obvious linear.

Morphology of High-Performance Rigid-Rod Polymer Fibers and Molecular Composites

1989 ◽  
Vol 47 ◽  
pp. 338-339
Author(s):  
W.W. Adams ◽  
S. J. Krause
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
Liquid Crystalline ◽  
Molecular Level ◽  
Synergistic Effects ◽  
Tensile Modulus ◽  
Commercial Development ◽  
The Matrix ◽  
Molecular Composites ◽  
Rigid Rod

Rigid-rod polymers such as PBO, poly(paraphenylene benzobisoxazole), Figure 1a, are now in commercial development for use as high-performance fibers and for reinforcement at the molecular level in molecular composites. Spinning of liquid crystalline polyphosphoric acid solutions of PBO, followed by washing, drying, and tension heat treatment produces fibers which have the following properties: density of 1.59 g/cm3; tensile strength of 820 kpsi; tensile modulus of 52 Mpsi; compressive strength of 50 kpsi; they are electrically insulating; they do not absorb moisture; and they are insensitive to radiation, including ultraviolet. Since the chain modulus of PBO is estimated to be 730 GPa, the high stiffness also affords the opportunity to reinforce a flexible coil polymer at the molecular level, in analogy to a chopped fiber reinforced composite. The objectives of the molecular composite concept are to eliminate the thermal expansion coefficient mismatch between the fiber and the matrix, as occurs in conventional composites, to eliminate the interface between the fiber and the matrix, and, hopefully, to obtain synergistic effects from the exceptional stiffness of the rigid-rod molecule. These expectations have been confirmed in the case of blending rigid-rod PBZT, poly(paraphenylene benzobisthiazole), Figure 1b, with stiff-chain ABPBI, poly 2,5(6) benzimidazole, Fig. 1c A film with 30% PBZT/70% ABPBI had tensile strength 190 kpsi and tensile modulus of 13 Mpsi when solution spun from a 3% methane sulfonic acid solution into a film. The modulus, as predicted by rule of mixtures, for a film with this composition and with planar isotropic orientation, should be 16 Mpsi. The experimental value is 80% of the theoretical value indicating that the concept of a molecular composite is valid.

scholarly journals Polymer/Iron-Based Layered Double Hydroxides as Multifunctional Wound Dressings

Pharmaceutics ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 1130
Author(s):  
Mariana Pires Figueiredo ◽  
Ana Borrego-Sánchez ◽  
Fátima García-Villén ◽  
Dalila Miele ◽  
Silvia Rossi ◽  
...  
Keyword(s):  
Drug Release ◽  
High Performance ◽  
Mechanical Performance ◽  
Release Kinetics ◽  
Wound Dressings ◽  
In Vitro Drug Release ◽  
Improved Performance ◽  
Double Hydroxide ◽  
Double Hydroxides

This work presents the development of multifunctional therapeutic membranes based on a high-performance block copolymer scaffold formed by polyether (PE) and polyamide (PA) units (known as PEBA) and layered double hydroxide (LDH) biomaterials, with the aim to study their uses as wound dressings. Two LDH layer compositions were employed containing Mg2+ or Zn2+, Fe3+ and Al3+ cations, intercalated with chloride anions, abbreviated as Mg-Cl or Zn-Cl, or intercalated with naproxenate (NAP) anions, abbreviated as Mg-NAP or Zn-NAP. Membranes were structurally and physically characterized, and the in vitro drug release kinetics and cytotoxicity assessed. PEBA-loading NaNAP salt particles were also prepared for comparison. Intercalated NAP anions improved LDH–polymer interaction, resulting in membranes with greater mechanical performance compared to the polymer only or to the membranes containing the Cl-LDHs. Drug release (in saline solution) was sustained for at least 8 h for all samples and release kinetics could be modulated: a slower, an intermediate and a faster NAP release were observed from membranes containing Zn-NAP, NaNAP and Mg-NAP particles, respectively. In general, cell viability was higher in the presence of Mg-LDH and the membranes presented improved performance in comparison with the powdered samples. PEBA containing Mg-NAP sample stood out among all membranes in all the evaluated aspects, thus being considered a great candidate for application as multifunctional therapeutic dressings.

Effect of Polyethylene Glycol in Nanocellulose/PLA Composites

2019 ◽  
Vol 821 ◽  
pp. 89-95
Author(s):  
Wanasorn Somphol ◽  
Thipjak Na Lampang ◽  
Paweena Prapainainar ◽  
Pongdhorn Sae-Oui ◽  
Surapich Loykulnant ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Lactic Acid ◽  
Polyethylene Glycol ◽  
Aspect Ratio ◽  
Mechanical Performance ◽  
Tensile Modulus ◽  
Poly Lactic Acid ◽  
Solvent Casting ◽  
Casting Method ◽  
Mediated Oxidation

Poly (lactic acid) or PLA was reinforced by nanocellulose and polyethylene glycol (PEG), which were introduced into PLA matrix from 0 to 3 wt.% to enhance compatibility and strength of the PLA. The nanocellulose was prepared by TEMPO-mediated oxidation from microcrystalline cellulose (MCC) powder and characterized by TEM, AFM, and XRD to reveal rod-like shaped nanocellulose with nanosized dimensions, high aspect ratio and high crystallinity. Films of nanocellulose/PEG/PLA nanocomposites were prepared by solvent casting method to evaluate the mechanical performance. It was found that the addition of PEG in nanocellulose-containing PLA films resulted in an increase in tensile modulus with only 1 wt% of PEG, where higher PEG concentrations negatively impacted the tensile strength. Furthermore, the tensile strength and modulus of nanocellulose/PEG/PLA nanocomposites were higher than the PLA/PEG composites due to the existence of nanocellulose chains. Visual traces of crazing were detailed to describe the deformation mechanism.

Sign in / Sign up

Export Citation Format

Share Document