scholarly journals Flexural Performance of Built-Up Beams Made with Plantation Wood

Forests ◽  
2019 ◽  
Vol 10 (8) ◽  
pp. 647 ◽  
Author(s):  
Tsai-Po Chien ◽  
Te-Hsin Yang ◽  
Feng-Cheng Chang
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Flexural Rigidity ◽  
Japanese Cedar ◽  
Formaldehyde Resin ◽  
Bottom Flange ◽  
Horizontal Shear ◽  
Load Bearing ◽  
Linear Behavior ◽  
The Web

In this study, Japanese cedar (Cryptomeria japonica (L. f.) D. Don) harvested from a plantation in Taiwan was used to develop built-up beams using self-tapping screws as metal connectors and resorcinol formaldehyde resin as glue to assemble components based on various assembly configurations. Results showed that adding glue provided flexural rigidity, whereas assembly using self-tapping screws resulted in built-up beams with high ductility but relatively low flexural bearing capacity. Beams used glue exhibited approximately linear behavior, whereas those using only screws exhibited some undulating and stepwise responses, implying that shear force between the flanges and the web may cause buckling as well as the dislocation of the self-tapping screws. When using components of similar grades, adding another web can improve the performance. Furthermore, the grades of flanges can strongly influence the flexural load-bearing capacity. In addition, a smaller spacing between the screws can improve the flexural load-bearing performance, but also cause wooden components to crack. Typical bending failure modes were observed in the developed built-up beams, indicating tension failure of the bottom flange as well as slippage between flanges and the web due to horizontal shear, which also caused buckling deformations in the screws.

scholarly journals Tests and Analyses of Slotted-In Steel-Plate Connections in Composite Timber Shear Wall Panels

2017 ◽  
Vol 2017 ◽  
pp. 1-20
Author(s):  
Ulf Arne Girhammar ◽  
Bo Källsner
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Design Method ◽  
Shear Walls ◽  
Test Results ◽  
Horizontal Shear ◽  
Load Bearing Capacity ◽  
Wood Panel ◽  
Load Bearing ◽  
Plate Connections

The authors present an experimental and analytical study of slotted-in connections for joining walls in the Masonite flexible building (MFB) system. These connections are used for splicing wall elements and for tying down uplifting forces and resisting horizontal shear forces in stabilizing walls. The connection plates are inserted in a perimeter slot in the PlyBoard™ panel (a composite laminated wood panel) and fixed mechanically with screw fasteners. The load-bearing capacity of the slotted-in connection is determined experimentally and derived analytically for different failure modes. The test results show ductile postpeak load-slip characteristics, indicating that a plastic design method can be applied to calculate the horizontal load-bearing capacity of this type of shear walls.

scholarly journals Study on an Innovative Flange Bolted-Welded Connection

2015 ◽  
Vol 9 (1) ◽  
pp. 870-875
Author(s):  
Yufeng Jiao ◽  
Guo Zhao
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Experimental Studies ◽  
High Strength ◽  
Bottom Flange ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Hybrid Joint ◽  
Welded Connection ◽  
Cyclic Loading Tests

This paper proposes a new type of spliced joint, named flange bolted-welded hybrid joint, which is designed to splice I-shape beam to facilitate the construction of industrialized buildings. The flange, welded with the bottom beam flange as well as the web close to bottom flange, are jointed by high strength bolts. Stiffening plate is welded at top of the flange while downhand welding and high strength friction grip bolts are used for the top beam flange and the beam web, respectively. The connection reduces the construction period and costs. In this paper, monotonic and reversed cyclic loading tests were conducted on three full-scale specimens of this innovative joint to investigate its load-bearing capacity, energy-dissipating capacity and failure modes. The results indicate that the joint has high load-bearing capacity and great ductility. The failure mode is due to the slippage of flange bolts as well as the gap development between the two flange plates. The experimental studies enabled improvement of the design of the connection to be used in moment-resisting steel frame structures.

scholarly journals Bending Stiffness, Load-Bearing Capacity and Flexural Rigidity of Slender Hybrid Wood-Based Beams

Forests ◽  
2018 ◽  
Vol 9 (11) ◽  
pp. 703 ◽  
Author(s):  
Barbara Šubic ◽  
Gorazd Fajdiga ◽  
Jože Lopatič
Keyword(s):  
Bearing Capacity ◽  
Flexural Rigidity ◽  
Bending Stiffness ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Reinforced Polymer ◽  
Glass Fibre Reinforced Polymer ◽  
Carbon Fibre Reinforced Polymer ◽  
Hybrid Beams ◽  
Fibre Reinforced Polymer

Modern architecture suggests the use of opened spaces with large transparent envelope surfaces. Therefore, windows of long widths and large heights are needed. In order to withstand the wind loads, such wooden windows can be reinforced with stiffer materials, such as aluminium (Al), glass-fibre reinforced polymer (GFRP), and carbon-fibre reinforced polymer (CFRP). The bending stiffness, load-bearing capacity, and flexural rigidity of hybrid beams, reinforced with aluminium, were compared through experimental analysis, using a four-point bending tests method, with those of reference wooden beams. The largest increases in bending stiffness (29%–39%), load-bearing capacity (33%–45%), and flexural rigidity (43%–50%) were observed in the case of the hybrid beams, with the highest percentage of reinforcements (12.9%—six reinforcements in their tensile and six reinforcements in their compressive zone). The results of the experiments confirmed the high potential of using hybrid beams to produce large wooden windows, for different wind zones, worldwide.

Effect of Concrete-Filled in Chord Tubes on Mechanical Behavior of RHS Steel Tube Trusses

2010 ◽  
Vol 163-167 ◽  
pp. 2171-2175 ◽  
Author(s):  
Jun Ping Liu ◽  
Yong Jian Liu ◽  
Jian Yang
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Steel Tube ◽  
Structural Stiffness ◽  
Static Behavior ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Compression Load ◽  
Hollow Section ◽  
Joint Deformation

Based on the experimental results, this paper presents the effects of concrete-filled in chord on the static behavior of rectangular hollow section (RHS) steel tubular trusses, including failure modes, load bearing capacity and structural stiffness. Failure of RHS trusses occurs at joints wether concrete-filled in chord or not, concrete-filled in chord changed the failure mode. Load bearing capacity and stiffness of joints subjected to compression load increased significantly, while it is limited to the tension joints. Concrete-filled in the compression chord tube can increase its stiffness significantly, while tension chord tube, it is not that obvious. Finally, based on the results discussed, failure modes and their formulas of calculating the load bearing capacity are discussed. Meanwhile, two methods, that is, amplified factor method and stiffness discounting method, which calculate the structural displacement when considering the joint deformation effects are presented.

Assesment of Main Models for Predicting Debonding Load-Bearing Capacity against Intermediate Crack-Induced Debonding Failure in FRP-Strengthened RC Beams

2011 ◽  
Vol 311-313 ◽  
pp. 1941-1944
Author(s):  
Gui Bing Li ◽  
Yu Gang Guo ◽  
Xiao Yan Sun
Keyword(s):  
Bearing Capacity ◽  
Failure Mode ◽  
Failure Modes ◽  
Rc Beams ◽  
Test Results ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Accuracy Test ◽  
New Models ◽  
Debonding Load

intermediate crack-induced debondingis one of the most dominant failure modes in FRP-strengthened RC beams. Different code models and provisions have been proposed to mitigateintermediate crack-induced debondingfailure.However, these models and provisions can not mitigate this failure mode effectively. Recnetly, new models have been proposed to solve this problem. Out of all the existing models, four typical ones are investigated in the current study. A comprehensivecomparison among these models is carried out in order to evaluate their performance and accuracy. Test results offlexural specimens with intermediate crack-induced debonding failurecollected from the existing literature are used in the current comparison. The effectivenessand accuracy of each model have been evaluated based on these experimental results. It is shown that the current modals are all conservative and inadequite to effectively mitigate intermediate crack-induced debonding in flexurally strengthened members.

scholarly journals Influence of the Ribs Parallel to Web on Warping and Load-Bearing Capacity of a Steel I-Beam

2019 ◽  
Vol 29 (4) ◽  
pp. 141-148 ◽  
Author(s):  
Krzysztof Wierzbicki ◽  
Maciej Szumigała
Keyword(s):  
Bearing Capacity ◽  
Cross Sections ◽  
Steel Plates ◽  
Steel Beam ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Plane Parallel ◽  
Steel Members ◽  
Plane Bending ◽  
The Web

Abstract The article analyses the method of enhancing a steel beam by adding additional steel members like ribs. They are rigidly connected with both flanges in a plane parallel to the web. That plates reduces warping during in-plane bending of steel beam under lateral-torsional bucking. Different thicknesses of steel plates used as ribs and different cross-sections were taken into account. Calculations were conducted using FEM and ABAQUS CAE environment. The outcomes were compared with ones from previous studies which concerned an influence of endplates on load-bearing capacity of an I-beam.

Study on failure mechanism and end construction influences of double rectangular tube assembled buckling-restrained brace

2016 ◽  
Vol 20 (10) ◽  
pp. 1572-1585 ◽  
Author(s):  
Zi-qin Jiang ◽  
Yan-lin Guo ◽  
Ai-Lin Zhang ◽  
Chao Dou ◽  
Cai-Xia Zhang
Keyword(s):  
Bearing Capacity ◽  
Rational Design ◽  
Failure Modes ◽  
High Strength ◽  
Design Parameters ◽  
Local Pressure ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Buckling Restrained Brace ◽  
Rectangular Tube

The double rectangular tube assembled buckling-restrained brace is a new type of buckling energy consumption buckling-restrained brace. Because of its external restraining members, which are bound by high-strength bolts, its mechanical mechanism is more complicated and its failure modes are more varied. In this study, the double rectangular tube assembled buckling-restrained brace composition and three types of end constructions are introduced in detail. The influences of different design parameters on the performance of double rectangular tube assembled buckling-restrained brace are studied by numerical analysis methods; the possible failure modes and the influence of the end strengthening construction of double rectangular tube assembled buckling-restrained brace are also investigated, and a number of suggestions are proposed to improve this design. This study shows that the pinned double rectangular tube assembled buckling-restrained brace has four types of typical failure modes, namely, overall buckling failure, external end local pressure-bearing failure, bending failure of the extended strengthened core region and bolt threading failure. Rational design can prevent a buckling-restrained brace from losing its load-bearing capacity. In addition, compared with the end strengthening scheme with an external hoop, the end strengthening scheme with a strengthened bench can improve the load-bearing capacity of the double rectangular tube assembled buckling-restrained brace more effectively, and a reasonable design can also save materials.

Experimental Study on Residual Load Bearing Capacity of SRC Eccentric Columns after Exposure to Fire

2010 ◽  
Vol 163-167 ◽  
pp. 2240-2246 ◽  
Author(s):  
Jun Hua Li ◽  
Yue Feng Tang ◽  
Ming Zhe Liu
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Ultimate Strength ◽  
Room Temperature ◽  
Ultimate Load ◽  
Flexural Rigidity ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Steel Reinforced Concrete

This paper provided three test data pertaining to the mechanical properties of steel reinforced concrete (SRC) eccentric columns after exposure to fire and one comparative test data pertaining to the mechanical properties of steel reinforced concrete columns at room temperature. The influence of eccentricity on failure mode, distortion performance and ultimate load bearing capacity are mainly studied. Test results show that the failure modes of steel reinforced concrete eccentric columns after exposure to fire are similar to that at room temperature. Strain along the section height at mid-span section of eccentric columns before loaded to 90% ultimate load bearing capacity is linearly distributed and well agree with the plane section supposition. After exposure to fire, the flexural rigidity and load bearing capacity of specimens are all declined compared with that at normal temperature. In various loading stages from the initial loading to 80% ultimate strength, the ratio of flexural rigidity of SRC eccentric columns after exposure to fire and at normal temperature is ranged from 0.30 to 0.59. With the same concrete strength and heating condition, the ultimate strength of specimens decreases with the increasing of eccentricity. The ultimate bearing capacity of all specimens at normal room temperature is calculated on the method proposed by Chinese regulation JGJ 138-2001. The compared results of experimental values and calculating values show that the residual load bearing capacity of SRC eccentric columns after exposure to fire is about 69% to 81% of that at room temperature.

scholarly journals Structural performance of textile reinforced concrete sandwich panels under axial and transverse load

2021 ◽  
Vol 60 (1) ◽  
pp. 64-79
Author(s):  
Junqing Hong ◽  
Shaofeng Zhang ◽  
Hai Fang ◽  
Xunqian Xu ◽  
Honglei Xie ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Failure Modes ◽  
Ultimate Load ◽  
Wire Mesh ◽  
Transverse Load ◽  
Composite Panels ◽  
Textile Reinforced Concrete ◽  
Load Bearing Capacity ◽  
Load Bearing

Abstract The performance of textile reinforced concrete composite panels (TRCCPs) under the action of pseudo-static load up to collapse was evaluated. The test of TRCCPs under axial and transverse loading was conducted, and the results were compared with those for steel wire mesh reinforced-concrete composite panels (SMRCCPs). Ceram-site concrete was utilized as the panel matrix owing to its lightweight and insulation characteristics. The ultimate load bearing capacity, load-deformation and load-strain relationships, and failure modes were discussed and investigated in comparison with the findings of non-linear finite-element-model (FEM) analysis and the analytic method on the basis of the reinforced concrete (RC) theory. The analysis results indicate that TRCCP is suitable for use as a potential structural member for a wall or slab system of buildings, and the typical RC theory can be applied to predict the ultimate load bearing capacity if modified suitably.

Sign in / Sign up

Export Citation Format

Share Document