scholarly journals Grasp Posture Control of Wearable Extra Robotic Fingers with Flex Sensors Based on Neural Network

Electronics ◽  
2020 ◽  
Vol 9 (6) ◽  
pp. 905 ◽  
Author(s):  
Joga Dharma Setiawan ◽  
Mochammad Ariyanto ◽  
M. Munadi ◽  
Muhammad Mutoha ◽  
Adam Glowacz ◽  
...  
Keyword(s):  
Neural Network ◽  
Haptic Feedback ◽  
Control Method ◽  
Middle Finger ◽  
Object Manipulation ◽  
Robotic System ◽  
Robotic Motion ◽  
Trained Neural Network ◽  
Flex Sensors ◽  
Robotic Fingers

This study proposes a data-driven control method of extra robotic fingers to assist a user in bimanual object manipulation that requires two hands. The robotic system comprises two main parts, i.e., robotic thumb (RT) and robotic fingers (RF). The RT is attached next to the user’s thumb, while the RF is located next to the user’s little finger. The grasp postures of the RT and RF are driven by bending angle inputs of flex sensors, attached to the thumb and other fingers of the user. A modified glove sensor is developed by attaching three flex sensors to the thumb, index, and middle fingers of a wearer. Various hand gestures are then mapped using a neural network. The input data of the robotic system are the bending angles of thumb and index, read by flex sensors, and the outputs are commanded servo angles for the RF and RT. The third flex sensor is attached to the middle finger to hold the extra robotic finger’s posture. Two force-sensitive resistors (FSRs) are attached to the RF and RT for the haptic feedback when the robot is worn to take and grasp a fragile object, such as an egg. The trained neural network is embedded into the wearable extra robotic fingers to control the robotic motion and assist the human fingers in bimanual object manipulation tasks. The developed extra fingers are tested for their capacity to assist the human fingers and perform 10 different bimanual tasks, such as holding a large object, lifting and operate an eight-inch tablet, and lifting a bottle, and opening a bottle cap at the same time.

scholarly journals Comparative Analysis of Neural-Network and Fuzzy Auto-Tuning Sliding Mode Controls for Overhead Cranes under Payload and Cable Variations

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Muhammad A. Shehu ◽  
Ai-jun Li ◽  
Bing Huang ◽  
Yu Wang ◽  
Bojian Liu
Keyword(s):  
Neural Network ◽  
High Speed ◽  
Control Method ◽  
Sliding Mode ◽  
Back Propagation ◽  
Absolute Error ◽  
Overhead Crane ◽  
Operating Personnel ◽  
Fuzzy Algorithms ◽  
Trained Neural Network

The overhead crane is required to operate fast and precisely with minimal sway. However, high-speed operations cause undesirable load sways, hazardous to operating personnel, the payload being handled, and the crane itself. Thus, a high-quality control is required. In this work, the nonlinear model of the overhead crane was established and the sliding mode control (SMC) was proposed that ensured the existence of sliding motion in the presence of payload and hoisting height variations, and viscous frictions. To maximize the benefits derived from the proposed control method, novel sliding slope-update based on intelligent neural-network and fuzzy algorithms were developed to tune the controller, guaranteeing precise tracking of the actuated variables as well as regulation of the unactuated variables. The proposed methods adjust predetermined value of the sliding manifold’s slope in response to variations in hoisting heights. Control applications were conducted, and results based on graphical, integral absolute error (IAE), and integral time absolute error (ITAE) proved the effectiveness of the proposed algorithms. It was observed that the response of the controller with back-propagation-trained neural-network was more effective relative to that of the fuzzy algorithm.

scholarly journals An Improved PID Controller for the Compliant Constant-Force Actuator Based on BP Neural Network and Smith Predictor

2021 ◽  
Vol 11 (6) ◽  
pp. 2685
Author(s):  
Guojin Pei ◽  
Ming Yu ◽  
Yaohui Xu ◽  
Cui Ma ◽  
Houhu Lai ◽  
...  
Keyword(s):  
Neural Network ◽  
Bp Neural Network ◽  
Pid Control ◽  
Pid Controller ◽  
Experimental Validation ◽  
Control Method ◽  
Smith Predictor ◽  
Constant Force ◽  
Matlab Simulation ◽  
Adjustment Time

A compliant constant-force actuator based on the cylinder is an important tool for the contact operation of robots. Due to the nonlinearity and time delay of the pneumatic system, the traditional proportional–integral–derivative (PID) method for constant force control does not work so well. In this paper, an improved PID control method combining a backpropagation (BP) neural network and the Smith predictor is proposed. Through MATLAB simulation and experimental validation, the results show that the proposed method can shorten the maximum overshoot and the adjustment time compared with traditional the PID method.

scholarly journals Analysis of the Nosema Cells Identification for Microscopic Images

Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3068
Author(s):  
Soumaya Dghim ◽  
Carlos M. Travieso-González ◽  
Radim Burget
Keyword(s):  
Neural Network ◽  
Machine Learning ◽  
Image Processing ◽  
Deep Learning ◽  
The Other ◽  
Support Vector ◽  
Learning Approaches ◽  
Microscopic Images ◽  
Trained Neural Network ◽  
Nosema Disease

The use of image processing tools, machine learning, and deep learning approaches has become very useful and robust in recent years. This paper introduces the detection of the Nosema disease, which is considered to be one of the most economically significant diseases today. This work shows a solution for recognizing and identifying Nosema cells between the other existing objects in the microscopic image. Two main strategies are examined. The first strategy uses image processing tools to extract the most valuable information and features from the dataset of microscopic images. Then, machine learning methods are applied, such as a neural network (ANN) and support vector machine (SVM) for detecting and classifying the Nosema disease cells. The second strategy explores deep learning and transfers learning. Several approaches were examined, including a convolutional neural network (CNN) classifier and several methods of transfer learning (AlexNet, VGG-16 and VGG-19), which were fine-tuned and applied to the object sub-images in order to identify the Nosema images from the other object images. The best accuracy was reached by the VGG-16 pre-trained neural network with 96.25%.

Robotic motion compensation for bone movement, using ultrasound images

2015 ◽  
Vol 42 (5) ◽  
pp. 466-474 ◽  
Author(s):  
P.M.B. Torres ◽  
P. J. S. Gonçalves ◽  
J.M.M. Martins
Keyword(s):  
Motion Compensation ◽  
Optical Measurement ◽  
Three Dimensional ◽  
Point Clouds ◽  
Robotic System ◽  
Ultrasound Images ◽  
Bone Drilling ◽  
Content Type ◽  
3D Point Clouds ◽  
Robotic Motion

Purpose – The purpose of this paper is to present a robotic motion compensation system, using ultrasound images, to assist orthopedic surgery. The robotic system can compensate for femur movements during bone drilling procedures. Although it may have other applications, the system was thought to be used in hip resurfacing (HR) prosthesis surgery to implant the initial guide tool. The system requires no fiducial markers implanted in the patient, by using only non-invasive ultrasound images. Design/methodology/approach – The femur location in the operating room is obtained by processing ultrasound (USA) and computer tomography (CT) images, obtained, respectively, in the intra-operative and pre-operative scenarios. During surgery, the bone position and orientation is obtained by registration of USA and CT three-dimensional (3D) point clouds, using an optical measurement system and also passive markers attached to the USA probe and to the drill. The system description, image processing, calibration procedures and results with simulated and real experiments are presented and described to illustrate the system in operation. Findings – The robotic system can compensate for femur movements, during bone drilling procedures. In most experiments, the update was always validated, with errors of 2 mm/4°. Originality/value – The navigation system is based entirely on the information extracted from images obtained from CT pre-operatively and USA intra-operatively. Contrary to current surgical systems, it does not use any type of implant in the bone to track the femur movements.

Sign in / Sign up

Export Citation Format

Share Document