scholarly journals Effect of Vanadium Reinforcement on the Microstructure and Mechanical Properties of Magnesium Matrix Composites

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 806
Author(s):  
Liqing Sun ◽  
Shuai Sun ◽  
Haiping Zhou ◽  
Hongbin Zhang ◽  
Gang Wang ◽  
...  
Keyword(s):  
Grain Size ◽  
Grain Refinement ◽  
Milling Process ◽  
Mg Alloy ◽  
Matrix Composites ◽  
Magnesium Matrix Composites ◽  
Pinning Effect ◽  
Average Grain Size ◽  
The Matrix ◽  
Hot Press Sintering

In this work, vanadium particles (VP) were utilized as a novel reinforcement of AZ31 magnesium (Mg) alloy. The nanocrystalline (NC) AZ31–VP composites were prepared via mechanical milling (MM) and vacuum hot-press sintering. During the milling process, the presence of VP contributed to the cold welding and fracture mechanism, resulting in the acceleration of the milling process. Additionally, increasing the VP content accelerated the grain refinement of the matrix during the milling process. After milling for 90 h, the average grain size of AZ31-X wt % Vp (X = 5, 7.5, 10) was refined to only about 23 nm, 19 nm and 16 nm, respectively. In the meantime, VP was refined to sub-micron scale and distributed uniformly in the matrix, exhibiting excellent interfacial bonding with the matrix. After the sintering process, the average grain size of AZ31-X wt % VP (X = 5, 7.5, 10) composites still remained at the NC scale, which was mainly caused by the pinning effect of VP. Besides that, the porosity of the sintered composites was no more than 7.8%, indicating a good densification effect. As a result, there was little difference between the theoretical and real density. Compared to as-cast AZ31 Mg alloy, the microhardness of sintered AZ31-X wt % VP (X = 5, 7.5, 10) composites increased by 65%, 87% and 96%, respectively, owing to the strengthening mechanisms of grain refinement strengthening, Orowan strengthening and load-bearing effects.

scholarly journals Effect of Content and Size of Reinforcements on the Grain Evolution of Graphene-Reinforced Aluminum Matrix Composites

Nanomaterials ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 2550
Author(s):  
Qi Wu ◽  
Pengfei Cai ◽  
Lianchun Long
Keyword(s):  
Grain Size ◽  
Grain Growth ◽  
High Performance ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Pinning Effect ◽  
High Temperature Processes ◽  
Average Grain Size ◽  
Size And Morphology

Graphene-reinforced aluminum matrix composites (GRAMCs) attract great interest in industries due to their high performance potential. High-temperature processes such as sintering and aging are usually applied during the preparation of GRAMCs, leading to grain coarsening that significantly influences its properties. In this work, a modified 3D Monte Carlo Potts model was proposed to investigate the effect of content and size of graphene on the grain evolution during the heat treatment of GRAMCs. Grain growth with graphene contents from 0.5 wt.% to 4.5 wt.% and sizes from 5 μm to 15 μm were simulated. The grain growth process, final grain size and morphology of the microstructure were predicted. The results indicated that both the content and size of the reinforcements had an impact on the grain evolution. The pinning effect of grain size can be enhanced by increasing the content and decreasing the size of graphene. Agglomeration and self-contacting phenomena of the graphene arose obviously when the contents and sizes were relatively high. The average grain size decreased by 48.77% when the content increased from 0.5 wt.% to 4.5 wt.%. The proposed method and predicted regulations can provide a reference for the design and fabrication of GRAMCs.

Microstructure and Mechanical Properties of Quasicrystal Reinforced Magnesium Matrix Composites

2011 ◽  
Vol 686 ◽  
pp. 242-246
Author(s):  
Xu Dong Wang ◽  
Wen Bo Du ◽  
Chao Hui Wang ◽  
Shu Bo Li
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Maximum Yield ◽  
Icosahedral Quasicrystal ◽  
Strengthening Effect ◽  
Magnesium Matrix Composites ◽  
Fine Grain ◽  
Average Grain Size ◽  
The Matrix ◽  
Maximum Yield Strength

Magnesium-based composites reinforced with stable icosahedral quasicrystal particles have been fabricated via Repeated Plastic Working (RPW) process. The microstructure of the composites has been investigated by XRD, SEM, TEM and HREM, and its mechanical properties have also been studied. The results showed that the RPW process could reduce the matrix grain size significantly, and the average grain size of matrix was only about 500 nm after 200 cycles of RPW. A good metallurgical bond interface between the quasicrystal particles and the Mg matrix was found. The composites exhibited the maximum yield strength of 265MPa and the maximum ultimate tensile strength of 309MPa at room temperature, respectively. The enhancement of mechanical properties is attributed to the strengthening effect of the quasicrystal particles and the fine-grain size of matrix.

scholarly journals Microstructure and Mechanical Properties of Magnesium Matrix Composites Interpenetrated by Different Reinforcement

2018 ◽  
Vol 8 (11) ◽  
pp. 2012 ◽  
Author(s):  
Shuxu Wu ◽  
Shouren Wang ◽  
Daosheng Wen ◽  
Gaoqi Wang ◽  
Yong Wang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Stainless Steel ◽  
Metal Matrix Composites ◽  
Grain Refinement ◽  
Metal Matrix ◽  
Matrix Composites ◽  
Magnesium Matrix ◽  
Magnesium Matrix Composites ◽  
Microstructure And Mechanical Properties

The present work discusses the microstructure and mechanical properties of the as-cast and as-extruded metal matrix composites interpenetrated by stainless steel (Fe–18Cr–9Ni), titanium alloy (Ti–6Al–4V), and aluminum alloy (Al–5Mg–3Zn) three-dimensional network reinforcement materials. The results show that the different reinforcement materials have different degrees of improvement on the microstructures and mechanical properties of the magnesium matrix composites. Among them, magnesium matrix composites interpenetrated by stainless steel reinforcement have maximum tensile strength, yield strength, and elongation, which are 355 MPa, 241 MPa, and 13%, respectively. Compared with the matrix, it increases by 47.9%, 60.7% and 85.7%, respectively. Moreover, compared with the as-cast state, the as-extruded sample has a relatively small grain size and a uniform size distribution. The grain size of the as-cast magnesium matrix composites is mainly concentrated at 200–300 μm, whereas the extruded state is mainly concentrated at 10–30 μm. The reason is that the coordination deformation of reinforcement and matrix, and the occurrence of dynamic recrystallization, cause grain refinement of magnesium matrix composite during the extrusion process, thereby improving its mechanical properties. Moreover, the improvement is attributed to the effect of the reinforcement itself, and the degree of grain refinement of the metal matrix composites.

Modeling and Numerical Simulation Research on Hollow Steel Ingot Forging Process of Heavy Cylinder Forging

2013 ◽  
Vol 712-715 ◽  
pp. 627-632
Author(s):  
Min Liu ◽  
Qing Xian Ma
Keyword(s):  
Numerical Simulation ◽  
Grain Size ◽  
Shear Zone ◽  
Grain Refinement ◽  
Steel Ingot ◽  
Effective Strain ◽  
Meridian Plane ◽  
Forging Process ◽  
Forming Load ◽  
Average Grain Size

Aiming at the disadvantages of low utilization ratio of steel ingot, uneven microstructure properties and long production period in the solid steel ingot forging process of heavy cylinder forgings such as reactor pressure vessel, a new shortened process using hollow steel ingot was proposed. By means of modeling of lead sample and DEFORM-3D numerical simulation, the deformation law and grain refinement behavior for 162 ton hollow steel ingot upsetting at different reduction ratios, pressing speeds and friction factors were investigated, and the formation rule of inner-wall defects in upsetting of hollow steel ingots with different shape factors was further analyzed. Simulation results show that the severest deformation occurs in the shear zone of meridian plane in the upsetting process of hollow steel ingot, and the average grain size in the shear zone is the smallest. As pressing speed increases, the forming load gradually increases and the deformation uniformity gets worse, while the average grain size decreases. An increase in friction factor can increase the peak value of effective strain, but it significantly reduces the deformation uniformity, increases the forming load and goes against grain refinement. Moreover, the four kinds of defects on the inner wall of steel ingot can be eliminated effectively by referring to the plotted defect control curve for hollow steel ingot during high temperature upsetting.

Development of Analytical Force Model for End Milling of Magnesium Matrix Composites

2020 ◽  
Author(s):  
Nishita Anandan ◽  
M. Ramulu
Keyword(s):  
End Milling ◽  
Coefficient Of Thermal Expansion ◽  
Cutting Edge ◽  
Force Model ◽  
Matrix Composites ◽  
Magnesium Metal ◽  
Magnesium Matrix Composites ◽  
The Matrix ◽  
Thrust Forces ◽  
Good Agreement

Abstract An analytical approach to predict the cutting forces in end milling of magnesium metal matrix composite is presented in this study. The model was developed by identifying three events that occur when the cutting edge encounters the composite, when an element of the cutting edge encounters just the particles, it may fracture the particle, when the element encounters pure ductile matrix, plastic deformation occurs and when the element is in contact with both the particle and matrix, particle debonding occurs due to mismatch in coefficient of thermal expansion. The probability of these events was estimated using the particle concentration and the distribution in the matrix. A cutting force model is developed by considering the stresses and forces experienced by the cutting edge contributed by these events. The predicted feed forces and the measured forces are in good agreement for most of the cutting conditions. While, the predictive thrust forces were found to diverge at higher feed of 1 mm/rev.

scholarly journals Grain Refinement of a Powder Nickel-Base Superalloy Using Hot Deformation and Slow-Cooling

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1978 ◽  
Author(s):  
Xianqiang Fan ◽  
Zhipeng Guo ◽  
Xiaofeng Wang ◽  
Jie Yang ◽  
Jinwen Zou
Keyword(s):  
Grain Size ◽  
Grain Refinement ◽  
Hot Deformation ◽  
Nickel Base Superalloy ◽  
Polycrystalline Nickel ◽  
Slow Cooling ◽  
Homogeneous Microstructure ◽  
Average Grain Size ◽  
Nickel Base ◽  
Base Superalloy

A pre-hot-deformation process was applied for a polycrystalline nickel-base superalloy to active deformation twins and dislocations, and subsequent slow cooling treatment was used to achieve grain refinement and microstructure homogenization. The microstructural evolution of the alloy was investigated, and the corresponding underlying mechanism was discussed. It was found that twinning mainly occurred in large grains during pre-hot-deformation owing to the stress concentration surrounding the large grains. High density dislocations were found in large grains, and the dislocation density increased approaching the grain boundary. The average grain size was refined from 30 μm to 13 μm after slow cooling with a standard deviation of grain size decreasing from 10.8 to 2.8, indicating a homogeneous microstructure. The grain refinement and microstructure homogenization during cooling process could be achieved via (i) static recrystallization (SRX), (ii) interaction of twin tips and γ’ precipitates, and (iii) grain coarsening hindered by γ’ precipitates in grain boundaries.

scholarly journals Rocess Design of Fiber Reinforced Magnesium Matrix Composites

2018 ◽  
Vol 1 (1) ◽  
Author(s):  
Ding Hualun
Keyword(s):  
Composite Materials ◽  
Matrix Composites ◽  
Deposition Method ◽  
Fiber Reinforced ◽  
Casting Method ◽  
Magnesium Matrix ◽  
Preparation Methods ◽  
Magnesium Matrix Composites ◽  
The Matrix ◽  
And Performance

This paper chooses magnesium as the matrix of composite materials, selects carbon fi ber as reinforcement, anddesigns the composite scheme according to the structure and performance of Mg-based composites. The performancecharacteristics and application prospect of fiber-reinforced magnesium matrix composites are introduced. Wait. Inthis paper, the process of preparing carbon fi ber magnesium matrix composites by compression casting method andspray deposition method is designed. The process fl ow chart of these two design schemes is determined by analyzingthe principle of these two kinds of preparation methods, and the specifi c problems of the process are analyzed andsummarized.

scholarly journals Crystallography of grain refinement in cast zinc–copper alloys

2015 ◽  
Vol 48 (3) ◽  
pp. 890-900 ◽  
Author(s):  
Zhilin Liu ◽  
Dong Qiu ◽  
Feng Wang ◽  
John A. Taylor ◽  
Mingxing Zhang
Keyword(s):  
Grain Size ◽  
Grain Refinement ◽  
Copper Alloys ◽  
Diffraction Method ◽  
Electron Backscattered Diffraction ◽  
Grain Coarsening ◽  
Cu Content ◽  
Edge Matching ◽  
Average Grain Size ◽  
Cast Alloys

Adding the peritectic forming element Cu effectively reduced the average grain size of cast Zn by over 85%. At a specified cast condition, the smallest grain size was obtained at 2 wt% Cu addition. A further increase in Cu content led to grain coarsening in the cast Zn–Cu alloys. Although the solute effect of Cu was predominately responsible for the grain refinement through restriction of the grain growth, it was found that the variation of grain size is also closely related to the formation of the pro-peritectic phase, ∊-CuZn4. Crystallographic calculations using the edge-to-edge matching model showed low interatomic misfit and interplanar mismatch between Zn and the ∊-CuZn4phase. In addition, a reproducible h.c.p.–h.c.p. (h.c.p. denotes hexagonal close-packed) orientation relationship between Zn and the ∊-CuZn4particles (located within the Zn grain centres) was also experimentally determined using the electron backscattered diffraction method. This indicated the high potency of the pro-peritectic ∊-CuZn4particles as effective heterogeneous nucleation sites for η-Zn, which further refined the Zn grains. However, when the Cu content was over 2.0 wt%, formation of large ∊-CuZn4particles resulted in grain coarsening of the cast alloys.

scholarly journals Strong Interactions between Austenite and the Matrix of Medium-Mn Steel during Intercritical Annealing

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3366 ◽  
Author(s):  
Tianpeng Zhou ◽  
Cunyu Wang ◽  
Chang Wang ◽  
Wenquan Cao ◽  
Zejun Chen
Keyword(s):  
Grain Size ◽  
Annealing Temperature ◽  
Ferrite Matrix ◽  
Strong Interactions ◽  
Recrystallization Process ◽  
Austenite Grain Size ◽  
Recrystallization Kinetics ◽  
Average Grain Size ◽  
The Matrix ◽  
Austenite Grains

The effects of heat treatment on the microstructure evolution was studied in regards to austenite nucleation and grain growth. It was found that the austenite nucleation and matrix recrystallization kinetics of samples annealed at 675 °C for different times were revealed, implying a strong interaction between the ferrite matrix and austenite. The recrystallization of the matrix during annealing provided favorable conditions for austenite nucleation and growth, and the formation of austenite during this process reduced the matrix recrystallization kinetics, thus delaying the recrystallization process of the matrix around the austenite grains. The statistical results for the austenite grain size under different annealing temperatures indicated that the average grain size of the austenite slightly increases with increasing of the annealing temperature, but the austenite with the largest grain size grows faster at the same temperature. This difference is attributed to the strict Kurdjumov Sachs (KS) orientation relationship (OR) between the austenite grains and the matrix, because the growth of austenite with a strict KS OR with the matrix is often inhibited during annealing. In contrast, the austenite maintains a non-strict KS OR with the matrix and can grow preferentially with increasing annealing temperature and time.

Sign in / Sign up

Export Citation Format

Share Document