scholarly journals Signal Strength Enhancement of Magnetostrictive Patch Transducers for Guided Wave Inspection by Magnetic Circuit Optimization

2019 ◽  
Vol 9 (7) ◽  
pp. 1477 ◽  
Author(s):  
Jianjun Wu ◽  
Zhifeng Tang ◽  
Keji Yang ◽  
Fuzai Lv
Keyword(s):  
Magnetic Field ◽  
Magnetic Circuit ◽  
Energy Conversion Efficiency ◽  
Wave Generation ◽  
Guided Wave ◽  
Shear Mode ◽  
Circuit Optimization ◽  
Affecting Factors ◽  
Long Distance ◽  
Dynamic Magnetic Field

Magnetostrictive patch transducers (MPT) with planar coils are ideal candidates for shear mode generation and detection in pipe and plate inspection with the advantages of flexibility, lightness and good directivity. However, the low energy conversion efficiency limits the application of the MPT in long distance inspection. In this article, a method for the enhancement of the MPT was proposed by dynamic magnetic field optimization using a soft magnetic patch (SMP). The SMP can reduce the magnetic resistance of the magnetic circuit, which increases the dynamic magnetic field intensity in the magnetostrictive patch during wave generation and restricts the induced dynamic magnetic field within the area around the coils for sensing during wave detection. Numerical simulations carried out at different frequencies verified the improvement of the dynamic magnetic fields by the SMP and influence of different affecting factors. The experimental validations of the signal enhancement in wave generation and detection were performed in an aluminum plate. The amplitude magnification could reach 12.7 dB when the MPTs were covered by the SMPs. Based on the numerical and experimental results, the SMP with a large relative permeability and thickness and close fitting between the SMP and coils were recommended when other application conditions were met.

scholarly journals Experimental Study of the Guided Wave Directivity Patterns of Thin Removable Magnetostrictive Patches

Sensors ◽  
2020 ◽  
Vol 20 (24) ◽  
pp. 7189
Author(s):  
Akram Zitoun ◽  
Steven Dixon ◽  
Graham Edwards ◽  
David Hutchins
Keyword(s):  
Magnetic Field ◽  
Experimental Study ◽  
Guided Waves ◽  
Permanent Magnets ◽  
Guided Wave ◽  
Metallic Plate ◽  
Static Magnetic Fields ◽  
Directivity Patterns ◽  
Spiral Coils ◽  
Dynamic Magnetic Field

The characteristics of removable magnetostrictive thin patches are investigated for the generation of guided waves in plates. The directivity patterns of SH, S0 and A0 modes have been measured in a thin metallic plate for different combinations of static and dynamic magnetic field directions. This used different coil geometries such as racetrack and spiral coils to generate the dynamic magnetic field, as well as separate biasing static magnetic fields from permanent magnets. This arrangement generated signals via both Lorentz and magnetostrictive forces, and the resultant emitted guided waves were studied for different dynamic and static magnetic field directions and magnitudes. It is demonstrated that different guided wave modes can be produced by controlling these parameters.

scholarly journals A Comparative Study of Three Types Shear Mode Piezoelectric Wafers in Shear Horizontal Wave Generation and Reception

Sensors ◽  
2018 ◽  
Vol 18 (8) ◽  
pp. 2681 ◽  
Author(s):  
Qiang Huan ◽  
Mingtong Chen ◽  
Faxin Li
Keyword(s):  
Energy Conversion ◽  
Conversion Efficiency ◽  
Energy Conversion Efficiency ◽  
Wave Generation ◽  
Shear Mode ◽  
Sh Wave ◽  
The Face ◽  
Piezoelectric Wafers ◽  
Shear Horizontal ◽  
Thickness Shear

Guided wave-based inspection has emerged as a promising tool to evaluate the reliability of key components in modern industries. The fundamental shear horizontal (SH0) wave is always of great interests for plate-like structures because of its non-dispersion characteristics. However, the generation and reception of SH0 wave using piezoelectric wafers is not straightforward. In this paper, we firstly define three types shear mode piezoelectric wafers, i.e., the conventional in-plane poled thickness-shear (d15) mode, the thickness-poled thickness-shear (d15) mode, and the face-shear (d24) mode. Then, finite element simulations were conducted to demonstrate their performance in SH wave generation and reception. The results indicated that the face shear d24 wafer can generate almost single mode SH0 wave, while both types of d15 wafers would generate Lamb waves and SH0 wave simultaneously. Finally, experiments were carried out to check the efficiency of different shear mode piezoelectric wafers in SH0 wave generation and reception. The results indicated that the d24 wafer can generate and receive SH0 wave of high signal to noise ratio (SNR) with high energy conversion efficiency, while the in-plane poled d15 wafer would generate SH0 wave of high amplitude and acceptable SNR but with relatively low energy conversion efficiency. The performances of thickness-poled d15 wafer was not as good as the other two in both SH wave generation and reception. This work will be helpful for the applications of SH waves in plate-like structures.

Axial guided wave characteristics in functionally graded one-dimensional hexagonal piezoelectric quasi-crystal cylinders

2021 ◽  
pp. 108128652110134
Author(s):  
B. Zhang ◽  
X.H. Wang ◽  
L. Elmaimouni ◽  
J.G. Yu ◽  
X.M. Zhang
Keyword(s):  
Coupling Effect ◽  
Energy Conversion Efficiency ◽  
Guided Wave ◽  
Functionally Graded ◽  
Phonon Modes ◽  
One Dimensional ◽  
Longitudinal Modes ◽  
Wave Characteristics ◽  
Piezoelectric Effects ◽  
Hollow Cylinders

In one-dimensional hexagonal piezoelectric quasi-crystals, there exist the phonon–phason, electro–phonon, and electro–phason couplings. Therefore, the phonon–phason coupling and piezoelectric effects on axial guided wave characteristics in one-dimensional hexagonal functionally graded piezoelectric quasi-crystal (FGPQC) cylinders are investigated by utilizing the Legendre polynomial series method. The dispersion curves and cut-off frequencies are illustrated. Wave characteristics in three hollow cylinders with different quasi-periodic directions are comparatively studied. Some new wave phenomena are revealed: the phonon–phason coupling and piezoelectric effects on the longitudinal and torsional phonon modes ( N = 0) vary as the quasi-periodic direction changes; the phonon–phason coupling effect on flexural–torsional modes in the r-, z-FGPQC hollow cylinders, and on flexural–longitudinal modes in ϑ-FGPQC hollow cylinders increases as N increases. The corresponding results obtained in this work lay the theoretical foundation for the design and manufacture of piezoelectric transducers with high resolution and energy-conversion efficiency.

scholarly journals Finite Element Analysis of Magnetic Field Exciter for Direct Testing of Magnetocaloric Materials’ Properties

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2792
Author(s):  
Wieslaw Lyskawinski ◽  
Wojciech Szelag ◽  
Cezary Jedryczka ◽  
Tomasz Tolinski
Keyword(s):  
Magnetic Field ◽  
Finite Element ◽  
Magnetic Circuit ◽  
Homogeneous Magnetic Field ◽  
Element Analysis ◽  
Mcm Testing ◽  
Testing Region ◽  
Magnetocaloric Materials ◽  
Field Excitation ◽  
The Magnetic Field

The paper presents research on magnetic field exciters dedicated to testing magnetocaloric materials (MCMs) as well as used in the design process of magnetic refrigeration systems. An important element of the proposed test stand is the system of magnetic field excitation. It should provide a homogeneous magnetic field with a controllable value of its intensity in the MCM testing region. Several concepts of a magnetic circuit when designing the field exciters have been proposed and evaluated. In the MCM testing region of the proposed exciters, the magnetic field is controlled by changing the structure of the magnetic circuit. A precise 3D field model of electromagnetic phenomena has been developed in the professional finite element method (FEM) package and used to design and analyze the exciters. The obtained results of the calculations of the magnetic field distribution in the working area were compared with the results of the measurements carried out on the exciter prototype. The conclusions resulting from the conducted research are presented and discussed.

scholarly journals Geomagnetic imprinting predicts spatio-temporal variation in homing migration of pink and sockeye salmon

2014 ◽  
Vol 11 (99) ◽  
pp. 20140542 ◽  
Author(s):  
Nathan F. Putman ◽  
Erica S. Jenkins ◽  
Catherine G. J. Michielsens ◽  
David L. G. Noakes
Keyword(s):  
Magnetic Field ◽  
Temporal Variation ◽  
Ocean Circulation ◽  
Sockeye Salmon ◽  
Movement Patterns ◽  
Oncorhynchus Gorbuscha ◽  
Migration Routes ◽  
Long Distance ◽  
Spatio Temporal ◽  
Olfactory Imprinting

Animals navigate using a variety of sensory cues, but how each is weighted during different phases of movement (e.g. dispersal, foraging, homing) is controversial. Here, we examine the geomagnetic and olfactory imprinting hypotheses of natal homing with datasets that recorded variation in the migratory routes of sockeye ( Oncorhynchus nerka ) and pink ( Oncorhynchus gorbuscha ) salmon returning from the Pacific Ocean to the Fraser River, British Columbia. Drift of the magnetic field (i.e. geomagnetic imprinting) uniquely accounted for 23.2% and 44.0% of the variation in migration routes for sockeye and pink salmon, respectively. Ocean circulation (i.e. olfactory imprinting) predicted 6.1% and 0.1% of the variation in sockeye and pink migration routes, respectively. Sea surface temperature (a variable influencing salmon distribution but not navigation, directly) accounted for 13.0% of the variation in sockeye migration but was unrelated to pink migration. These findings suggest that geomagnetic navigation plays an important role in long-distance homing in salmon and that consideration of navigation mechanisms can aid in the management of migratory fishes by better predicting movement patterns. Finally, given the diversity of animals that use the Earth's magnetic field for navigation, geomagnetic drift may provide a unifying explanation for spatio-temporal variation in the movement patterns of many species.

Inspection of Concrete-Metal Rod Interface Using Guided Waves

2000 ◽  
Author(s):  
Won-Bae Na ◽  
Tribikram Kundu ◽  
Mohammad R. Ehsani
Keyword(s):  
Lamb Wave ◽  
Guided Waves ◽  
Lamb Waves ◽  
Guided Wave ◽  
Ultrasonic Transducers ◽  
Interface Debonding ◽  
Long Distance ◽  
Steel Rebar ◽  
Steel Bars ◽  
Steel Rebars

Abstract The feasibility of detecting interface degradation and separation of steel rebars in concrete beams using Lamb waves is investigated in this paper. It is shown that Lamb waves can easily detect these defects. A special coupler between the steel rebar and ultrasonic transducers has been used to launch non-axisymmetric guided waves in the steel rebar. This investigation shows that the Lamb wave inspection technique is an efficient and effective tool for health monitoring of reinforced concrete structures because the Lamb wave can propagate a long distance along the reinforcing steel bars embedded in concrete as the guided wave and is sensitive to the interface debonding between the steel rebar and concrete.

THE ROTATIONAL EFFECT OF MAGNETIC PARTICLES ON CELLULAR APOPTOSIS BASED ON FOUR ELECTROMAGNET FEEDBACK CONTROL SYSTEM

2021 ◽  
pp. 2150045
Author(s):  
Jia Ji Lee ◽  
Chang Hong Pua ◽  
Misni Misran ◽  
Poh Foong Lee
Keyword(s):  
Magnetic Field ◽  
Electromagnetic Field ◽  
Control System ◽  
Feedback Control ◽  
Cell Apoptosis ◽  
Magnetic Particles ◽  
Drug Carriers ◽  
Feedback Control System ◽  
Rotational Effect ◽  
Dynamic Magnetic Field

Objectives: Magnetic drug targeting offers the latest popular alternative option to deliver magnetic drug carriers into targeting region body parts through manipulation of an external magnetic field. However, the effectiveness of using an electromagnetic field to manipulate and directing magnetic particles is yet to be established. Methods: In this paper, a homemade cost-effective electromagnet system was built for the purpose of studying the control and directing the magnetic drug carriers. The electromagnet system was built with four electromagnetic sources and tested the capability in directing the particles’ movement in different geometry patterns. Besides that, the creation of the self-rotation of individual magnetic particle clusters was achieved by using fast switching between magnetic fields. This self-rotation allows the possibility of cell apoptosis study to carry out. The system was constructed with four electromagnets integrated with a feedback control system and built to manipulate a droplet of commercially available iron (II, III) oxide nanoparticles to steer the magnetic droplet along different arbitrary trajectories (square, circle, triangle, slanted line) in 2-dimensional. Results: A dynamic magnetic field of 25 Hz was induced for magnetic nanoparticles rotational effect to observe the cell apoptosis. A profound outcome shows that the declining cell viability of the cell lines by 40% and the morphology of shrinking cells after the exposure of the dynamic magnetic field. Conclusion: The outcome from the pilot study gives an idea on the laboratory setup serves as a fundamental model for studying the electromagnetic field strength in applying mechanical force to target and to rotate for apoptosis on cancer cell line study.

Influence of Load and Air Gap Dimension on Magnetic Field and Magnetic Circuit Design of a Hightorque Stepmotor

1995 ◽  
pp. 343-346
Author(s):  
Wagner Juraj ◽  
Maga Dušan ◽  
Guba Roman ◽  
Führichová Renáta ◽  
Opaterný Jozef
Keyword(s):  
Magnetic Field ◽  
Circuit Design ◽  
Magnetic Circuit ◽  
Air Gap
Sign in / Sign up

Export Citation Format

Share Document