scholarly journals Multimode Guided Wave Detection for Various Composite Damage Types

2020 ◽  
Vol 10 (2) ◽  
pp. 484 ◽  
Author(s):  
Hanfei Mei ◽  
Robin James ◽  
Mohammad Faisal Haider ◽  
Victor Giurgiutiu
Keyword(s):  
Composite Plate ◽  
Guided Waves ◽  
Impact Damage ◽  
Guided Wave ◽  
Wave Detection ◽  
Composite Damage ◽  
Cfrp Composite ◽  
The Impact ◽  
Damage Types ◽  
Wave Modes

This paper presents a new methodology for detecting various types of composite damage, such as delamination and impact damage, through the application of multimode guided waves. The basic idea is that various wave modes have different interactions with various types of composite damage. Using this method, selective excitations of pure-mode guided waves were achieved using adjustable angle beam transducers (ABTs). The tuning angles of various wave modes were calculated using Snell’s law applied to the theoretical dispersion curves of composite plates. Pitch–catch experiments were conducted on a 2-mm quasi-isotropic carbon fiber-reinforced polymer (CFRP) composite plate to validate the excitations of pure fundamental symmetric mode (S0) and shear horizontal mode (SH0). The generated pure S0 mode and SH0 mode were used to detect and separate the simulated delamination and actual impact damage. It was observed that S0 mode was only sensitive to the impact damage, while SH0 mode was sensitive to both simulated delamination and impact damage. The use of pure S0 and SH0 modes allowed for damage separation. In addition, the proposed method was applied to a 3-mm-thick quasi-isotropic CFRP composite plate using multimode guided wave detection to distinguish between delamination and impact damage. The experimental results demonstrated that the proposed method has a good capability to detect and separate various damage types in composite structures.

scholarly journals Assessment of low-velocity impact damage in composites by the measure of second-harmonic guided waves with the phase-reversal approach

2019 ◽  
Vol 103 (1) ◽  
pp. 003685041988107 ◽  
Author(s):  
Weibin Li ◽  
Chang Jiang ◽  
Xinlin Qing ◽  
Liangbing Liu ◽  
Mingxi Deng
Keyword(s):  
Guided Waves ◽  
Second Harmonic ◽  
Impact Damage ◽  
Guided Wave ◽  
Second Order ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
Phase Reversal ◽  
The Impact

Structural strength and integrity of composites can be considerably affected by the low-velocity impact damage due to the unique characteristics of composites, such as layering bonded by adhesive and the weakness to impact. For such damage, there is an urgent need to develop advanced nondestructive testing approaches. Despite the fact that the second harmonics could provide information sensitive to the structural health condition, the diminutive amplitude of the measured second-order harmonic guided wave still limits the applications of the second-harmonic generation–based nonlinear guided wave approach. Herein, laminated composites suffered from low-velocity impact are characterized by use of nonlinear guided waves. An enhancement in the signal-to-noise ratio for the measure of second harmonics is achieved by a phase-reversal method. Results obtained indicate a monotonic correlation between the impact-induced damage in composites and the relative acoustic nonlinear indicator of guided waves. The experimental finding in this study shows that the measure of second-order harmonic guided waves with a phase-reversal method can be a promising indicator to impact damage rendering in an improved and reliable manner.

scholarly journals 3D Modelling of the Scattering of the Fundamental Anti-Symmetric Lamb Mode (A0) Propagating within a Point-Impacted Transverse-Isotropic Composite Plate

2021 ◽  
Vol 11 (16) ◽  
pp. 7276
Author(s):  
Dilbag Singh ◽  
Mourad Bentahar ◽  
Charfeddine Mechri ◽  
Rachid El Guerjouma
Keyword(s):  
Composite Plate ◽  
Impact Damage ◽  
Elastic Stiffness ◽  
Wave Mode ◽  
Guided Wave ◽  
Domain Model ◽  
Isotropic Composite ◽  
Damaged Zone ◽  
The Impact ◽  
Lamb Mode

The present paper deals with an effort to model impact damage in 3D-FE simulation. In this work, we studied the scattering behavior of an incident A0 guided wave mode propagating towards an impacted damaged zone created within a quasi-isotropic composite plate. Besides, barely visible impact damage of the desired energy was created and imaged using ultrasonic bulk waves in order to measure the size of the damage. The 3D-FE frequency domain model is then used to simulate the scattering of an incident guided wave at a frequency below an A1 cut-off with a wavelength comparable to the size of the damaged zone. The damage inside the plate is modeled as a conical-shaped geometry with decayed elastic stiffness properties. The model was first validated by comparing the directivity of the scattered fields for the A0 Lamb mode predicted numerically with the experimental measurements. The modeling of the impact zone with conical-shape geometry showed that the scattering directivity of the displacement field depends significantly on the size (depth and width) of the conical damage created during the point-impact of the composite with potential applications allowing the determination of the geometric characteristics of the impacted areas.

Guided Wave Generation and Propagation in Self-Sensing Piezoelectric Composite Plates for Structural Health Monitoring

2018 ◽  
Author(s):  
Junzhen Wang ◽  
Yanfeng Shen
Keyword(s):  
Finite Element ◽  
Impact Damage ◽  
Composite Plates ◽  
Wave Generation ◽  
Absorbing Boundary Conditions ◽  
Guided Wave ◽  
Piezoelectric Composite ◽  
Finite Element Software ◽  
The Impact ◽  
Wave Modes

This paper presents a systematic numerical investigation of guided wave generation, propagation, interaction with damage, and reception in anisotropic piezoelectric composite plates. This approach employs piezoelectric composite materials as both load bearing and sensing elements. Finite element modal analysis of a plate unit cell with Bloch-Floquet boundary condition is performed to understand the guided wave propagation characteristics in piezoelectric composite plates. The guided wave generation and tuning characteristics are investigated using the harmonic analysis model with absorbing boundary conditions. The relationship between the generated wave modes and the laminate layup orientations is studied. Subsequently, an impact damage is introduced and modeled as a group of cone shape delaminated layers and stiffness losses within the layers through the thickness direction. 2D and 3D transient dynamic coupled-field finite element models are constructed to simulate the procedure of guided wave generation, propagation, interaction with the impact damage, and reception in an orthotropic piezoelectric composite plate using the commercial finite element software (ANSYS). In addition, Contact Acoustic Nonlinearity (CAN) is simulated via time domain transient analysis. Advanced signal processing techniques are used to extract the distinctive nonlinear features. The frequency-wavenumber analysis is further adopted to decipher wave modes and frequency components in the scattered wave field. This paper finishes with concluding remarks and suggestions for future work.

scholarly journals Influence of Location and Thickness Variations on Guided Waves in Defective Carbon/Epoxy Plate

2019 ◽  
Vol 9 (1) ◽  
pp. 5736-5740
Keyword(s):  
Guided Waves ◽  
Wave Attenuation ◽  
Impact Damage ◽  
Plate Thickness ◽  
Element Model ◽  
Guided Wave ◽  
Ultrasonic Waves ◽  
Time Signal ◽  
Matrix Cracks ◽  
The Impact

This paper addresses the effects of plate thickness and defect location on guided wave propagation in carbon/epoxy plates. A three-dimensional (3D) finite element model (FEM) of the plate was developed using MATLAB program codes, and simulated in Abaqus/Explicit. Referring to experimental ultrasonic C-scan images, the complex impact damage was modelled with irregular-shaped delamination and through-thickness matrix cracks. The simulated results show that a slower arrival time signal and amplitude drop of guided wave captured behind the defective region can be used as an indicator of the impact damage. A largOer scattering occurred when delamination was located closer to the plate surface. The extent of scattering gets larger, especially in the direction of 345o from the excitation point. It is also observed that the impact damage can still be detected through a line scan method across the impact damage, although the wave attenuation is greater in a thicker composite plate. By investigating these factors independently, the trends of the scattered guided ultrasonic waves can be classified and perhaps will revolutionize a smart non-destructive method for composite structure in the future.

Contribution of Lamb wave modes in the formation of higher order modes cluster (HOMC) guided waves

2021 ◽  
pp. 095440622110424
Author(s):  
Z Abbasi ◽  
F Honarvar
Keyword(s):  
Finite Element ◽  
Wave Packet ◽  
Lamb Wave ◽  
Guided Waves ◽  
Element Model ◽  
Higher Order ◽  
Guided Wave ◽  
Cross Sectional ◽  
Higher Order Modes ◽  
Wave Modes

In recent years, Higher Order Modes Cluster (HOMC) guided waves have been considered for ultrasonic testing of plates and pipes. HOMC guided waves consist of higher order Lamb wave modes that travel together as a single nondispersive wave packet. The objective of this paper is to investigate the effect of frequency-thickness value on the contribution of Lamb wave modes in an HOMC guided wave. This is an important issue that has not been thoroughly investigated before. The contribution of each Lamb wave mode in an HOMC guided wave is studied by using a two-dimensional finite element model. The level of contribution of various Lamb wave modes to the wave cluster is verified by using a 2D FFT analysis. The results show that by increasing the frequency-thickness value, the order of contributing modes in the HOMC wave packet increases. The number of modes that comprise a cluster also increases up to a specific frequency-thickness value and then it starts to decrease. Plotting of the cross-sectional displacement patterns along the HOMC guided wave paths confirms the shifting of dominant modes from lower to higher order modes with increase of frequency-thickness value. Experimental measurements conducted on a mild steel plate are used to verify the finite element simulations. The experimental results are found to be in good agreement with simulations and confirm the changes observed in the level of contribution of Lamb wave modes in a wave cluster by changing the frequency-thickness value.

scholarly journals Fatigue crack detection in pipes with multiple mode nonlinear guided waves

2018 ◽  
Vol 18 (1) ◽  
pp. 180-192 ◽  
Author(s):  
Ruiqi Guan ◽  
Ye Lu ◽  
Kai Wang ◽  
Zhongqing Su
Keyword(s):  
Fatigue Crack ◽  
Crack Detection ◽  
Guided Waves ◽  
Second Harmonic ◽  
Experimental Testing ◽  
Harmonic Wave ◽  
Guided Wave ◽  
Element Analysis ◽  
Fatigue Crack Detection ◽  
Wave Modes

This study elaborates fundamental differences in fatigue crack detection using nonlinear guided waves between plate and pipe structures and provides an effective approach for analysing nonlinearity in pipe structures. For this purpose, guided wave propagation and interaction with microcrack in a pipe structure, which introduced a contact acoustic nonlinearity, was analysed through a finite element analysis in which the material nonlinearity was also included. To validate the simulation results, experimental testing was performed using piezoelectric transducers to generate guided waves in a specimen with a fatigue crack. Both methods revealed that the second harmonic wave generated by the breathing behaviour of the microcrack in a pipe had multiple wave modes, unlike the plate scenario using nonlinear guided waves. Therefore, a proper index which considered all the generated wave modes due to the microcrack was developed to quantify the nonlinearity, facilitating the identification of microscale damage and further assessment of the severity of the damage in pipe structures.

Ultrasonic Guided Wave Testing of Finned Tubing

2015 ◽  
Author(s):  
Owen M. Malinowski ◽  
Matthew S. Lindsey ◽  
Jason K. Van Velsor
Keyword(s):  
Wave Propagation ◽  
Guided Waves ◽  
Tube Wall ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Complex Nature ◽  
Inspection Method ◽  
Ultrasonic Guided Wave ◽  
Guided Wave Propagation ◽  
Wave Modes

In the past few decades, ultrasonic guided waves have been utilized more frequently Non-Destructive Testing (NDT); most notably, in the qualitative screening of buried piping. However, only a fraction of their potential applications in NDT have been fully realized. This is due, in part, to their complex nature, as well as the high level of expertise required to understand and utilize their propagation characteristics. The mode/frequency combinations that can be generated in a particular structure depend on geometry and material properties and are represented by the so-called dispersion curves. Although extensive research has been done in ultrasonic guided wave propagation in various geometries and materials, the treatment of ultrasonic guided wave propagation in periodic structures has received little attention. In this paper, academic aspects of ultrasonic guided wave propagation in structures with periodicity in the wave vector direction are investigated, with the practical purpose of developing an ultrasonic guided wave based inspection technique for finned tubing. Theoretical, numerical, and experimental methods are employed. The results of this investigation show excellent agreement between theory, numerical modeling, and experimentation; all of which indicate that ultrasonic guided waves will propagate coherently in finned tube only if the proper wave modes and frequencies are selected. It is shown that the frequencies at which propagating wave modes exist can be predicted theoretically and numerically, and depend strongly on the fin geometry. Furthermore, the results show that these propagating wave modes are capable of screening for and identifying the axial location of damage in the tube wall, as well as separation of the fins from the tube wall. The conclusion drawn from these results is that Guided Wave Testing (GWT) is a viable inspection method for screening finned tubing.

scholarly journals Modeling Analysis of Guided Ultrasonic Waves in Composite Plates with Impact Damage

2018 ◽  
Vol 7 (4.26) ◽  
pp. 175
Author(s):  
Noorfaten Asyikin Ibrahim ◽  
Bibi Intan Suraya Murat
Keyword(s):  
Composite Structures ◽  
Impact Damage ◽  
Composite Plates ◽  
Guided Wave ◽  
Ultrasonic Waves ◽  
Fe Model ◽  
Element Analysis ◽  
Damage Area ◽  
Guided Ultrasonic Waves ◽  
The Impact

This paper investigates the propagation of guided ultrasonic waves and the interaction with impact damage in composite plates using a full three-dimensional Finite Element analysis. Impact damage in the composite plate was modeled as rectangular- and T-shaped delaminations. In order to provide guidelines for extending the modeling of realistic multimode impact damage, the impact damage was modeled as a combination of the delamination and reduced materials properties. The information obtained from these methods was compared to the experimental results around the damage area for a validation. There was a reasonable similarity between the experimental and FE results. The FE simulations can effectively model the scattering characteristics of the A0 mode wave propagation in anisotropic composite plates. This suggests that the simplified and easy-to-implement FE model could be used to represent the complex impact damage in composite plates. This could be useful for the improvement of the FE modeling and performance of guided wave methods for the in-situ NDE of large composite structures. 

scholarly journals Numerical Investigation of Excitation of Various Lamb Waves Modes in Thin Plastic Films

2022 ◽  
Vol 12 (2) ◽  
pp. 849
Author(s):  
Rymantas Jonas Kazys ◽  
Justina Sestoke ◽  
Egidijus Zukauskas
Keyword(s):  
Numerical Investigation ◽  
Lamb Wave ◽  
Guided Waves ◽  
Phased Array ◽  
Ultrasonic Transducer ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Plastic Films ◽  
Thin Plastic ◽  
Wave Modes

Ultrasonic-guided waves are widely used for the non-destructive testing and material characterization of plates and thin films. In the case of thin plastic polyvinyl chloride (PVC), films up to 3.2 MHz with only two Lamb wave modes, antisymmetrical A0 and symmetrical S0, may propagate. At frequencies lower that 240 kHz, the velocity of the A0 mode becomes slower than the ultrasonic velocity in air which makes excitation and reception of such mode complicated. For excitation of both modes, we propose instead a single air-coupled ultrasonic transducer to use linear air-coupled arrays, which can be electronically readjusted to optimally excite and receive the A0 and S0 guided wave modes. The objective of this article was the numerical investigation of feasibility to excite different types of ultrasonic-guided waves, such as S0 and A0 modes in thin plastic films with the same electronically readjusted linear phased array. Three-dimensional and two-dimensional simulations of A0 and S0 Lamb wave modes using a single ultrasonic transducer and a linear phased array were performed. The obtained results clearly demonstrate feasibility to excite efficiently different guided wave modes in thin plastic films with readjusted phased array.

Sign in / Sign up

Export Citation Format

Share Document