scholarly journals The Effect of Reinforcement, Expanded Polystyrene (EPS) and The Effect of Reinforcement, Expanded Polystyrene (EPS) andThe Effect of Reinforcement, Expanded Polystyrene (EPS) and Fly Ash On The Strength of Foam Concrete

2016 ◽  
Vol 2 (2) ◽  
pp. 1-7 ◽  
Author(s):  
Rosli M. F. ◽  
Rashidi A. ◽  
Ahmed E. ◽  
Sarudu N. H
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Lightweight Concrete ◽  
Expanded Polystyrene ◽  
Wire Mesh ◽  
Replacement Level ◽  
Foam Concrete ◽  
Dead Load ◽  
Mesh Reinforcement

 Foam concrete is a type of lightweight concrete. The main characteristics of foam concrete are its low density and thermal conductivity. Its advantages are that there is a reduction of dead load, faster building rates in construction and lower haulage and handling costs. This research was conducted to investigate the compressive strength and flexural strength of reinforced foam concrete. The use of fly ash and Expanded Polystyrene (EPS) as cement and sand replacement were also included in the production of reinforced foam concrete. There were two types of reinforcements used to reinforce the foam concrete namely plastic and wire mesh. Physical failure mode, compressive strength and flexural strength of samples were compared and analyzed. The replacement percentages for both fly ash and EPS were varied between 0-50% and 0-40% respectively. The study showed that it is feasible to reinforce the foam concrete and the best result was obtained from wire mesh reinforcement. The study also showed that the optimum replacement level for both fly ash and EPS was 30% based on compressive and flexural strength results.

Influence of Foaming Agent on the Properties of High Density Foam Concrete

2011 ◽  
Vol 399-401 ◽  
pp. 1214-1217 ◽  
Author(s):  
Xin Gang Yu ◽  
Yan Na Gao ◽  
Lin Lin ◽  
Fang Li
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Concrete ◽  
Drying Shrinkage ◽  
High Strength ◽  
High Density ◽  
Low Density ◽  
Dilution Ratio ◽  
Foam Concrete ◽  
Foaming Agent

Lightweight concrete has been used for structural purposes for many years and it is developed very fast in resent years due to its lightweight and favourable for insulation properties. High strength foam concrete is a fairly new kind of lightweight concrete with excellent properties of outstanding workability, low density and high strength. Responsible for these properties are the macro-, meso- and micro- porosity of the foam concrete which are mainly affected by the foaming agent. The influence of foaming agent’s dilution ratio and foam dosage on the fluidity, compressive strength, flexural strength and drying shrinkage of high density foam concrete designed for structural materials is investigated in this paper.

The Study of Oil Palm Shell (OPS) Lightweight Concrete Using Superplasticizer, Silica Fume, and Fly Ash

2017 ◽  
Vol 902 ◽  
pp. 65-73 ◽  
Author(s):  
Elly Tjahjono ◽  
Ayudia M. Fani ◽  
Dodorus D. Dodi ◽  
Erinda P. Purnamasari ◽  
Feny A. Silaban ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Oil Palm ◽  
Coarse Aggregate ◽  
Lightweight Concrete ◽  
Crude Palm Oil ◽  
Concrete Technology ◽  
Palm Shell ◽  
Oil Palm Shell

The concrete technology has been growing significantly since years ago especially in Indonesia’s construction. Therefore, Indonesia needs new innovation of concrete technology to solve the problem for the availability of concrete material. Indonesia is known as the largest producer of crude palm oil (CPO) in the world. Oil palm shell (OPS) is one of the solid wastes produced in crude palm oil industry that can be used as concrete materials. This paper presents the experimental results of a research project to produce structural lightweight concrete using oil palm shell (OPS), as a coarse aggregate. This experimental was investigating the effects of adding silica fume, fly ash, and superplasticizer for the compressive strength and flexural strength of the OPS lightweight concrete. It was found that OPS lightweight concrete has compressive strength up to 23.90 MPa in 28-days and flexural strength up to 2.54 MPa in 28-days. This experimental concluded that OPS lightweight concrete has a good potential as a lightweight coarse aggregate and low-cost housing construction in Indonesia.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

scholarly journals Strength Time–Varying and Freeze–Thaw Durability of Sustainable Pervious Concrete Pavement Material Containing Waste Fly Ash

2018 ◽  
Vol 11 (1) ◽  
pp. 176 ◽  
Author(s):  
Hanbing Liu ◽  
Guobao Luo ◽  
Longhui Wang ◽  
Yafeng Gong
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Pervious Concrete ◽  
Early Age ◽  
Pavement Materials ◽  
Freeze Thaw ◽  
Replacement Method ◽  
Porosity And Permeability ◽  
Volume Method

Pervious concretes, as sustainable pavement materials, have great advantages in addressing a number of environmental issues. Fly ash, as the industrial by-product waste, is the most commonly used as cement substitute in concrete. The objective of this paper is to study the effects of waste fly ash on properties of pervious concrete. Fly ash was used to replace cement with equivalent volume method at different levels (3%, 6%, 9%, and 12%). The control pervious concrete and fly ash modified pervious concrete were prepared in the laboratory. The porosity, permeability, compressive strength, flexural strength, and freeze–thaw resistance of all mixtures were tested. The results indicated that the addition of fly ash decreased the early-age (28 d) compressive strength and flexural strength, but the long-term (150 d) compressive strength and flexural strength of fly ash modified pervious concrete were higher than that of the early-age. The adverse effect of fly ash on freeze–thaw resistance of pervious concrete was observed when the fly ash was added. The porosity and permeability of all pervious concrete mixtures changed little with the content of fly ash due to the use of equal volume replacement method. Although fly ash is not positive to the properties of pervious concrete, it is still feasible to apply fly ash as a substitute for cement in pervious concrete.

scholarly journals Kajian Karakteristik Beton Memadat Sendiri yang Menggunakan Serat Ijuk (Hal. 54-65)

2018 ◽  
Vol 4 (4) ◽  
pp. 54
Author(s):  
Iis Nurjamilah ◽  
Abinhot Sihotang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
High Strength ◽  
Self Compacting Concrete ◽  
Palm Fiber ◽  
Fiber Concrete ◽  
Dilute Mixture

ABSTRAKKajian karakteristik beton memadat sendiri yang menggunakan serat ijuk merupakan sebuah kajian yang dilakukan untuk mengetahui pengaruh penambahan serat ijuk terhadap karakteristik beton memadat sendiri (SCC). Beton memadat sendiri yang menggunakan serat ijuk (PFSCC) didesain memiliki campuran yang encer, bermutu tinggi (= 40 MPa) dan memiliki persentase kekuatan lentur yang lebih baik. PFSCC  didapatkan dari hasil pencampuran antara semen sebanyak 85%, fly ash 15%, superplastizicer 1,5%, serat ijuk 0%, 0,5%; 1%; 1,5%; 2% dan 3% dari berat binder (semen + fly ash), kadar air 190 kg/m3, agregat kasar 552,47 kg/m3 dan pasir 1.063 kg/m3. Semakin banyak persentase penambahan serat ijuk ke dalam campuran berdampak terhadap menurunnya workability beton segar. Penambahan serat ijuk yang paling baik adalah sebanyak 1%, penambahan tersebut dapat meningkatkan kekuatan tekan beton sebesar 13% dan lentur sebesar 1,8%.Kata kunci: beton memadat sendiri (SCC), beton berserat, beton memadat sendiri yang menggunakan serat ijuk (PFSCC), serat ijuk ABSTRACTThe study of characteristics self compacting concrete using palm fibers is a study conducted to determine the effect of adding palm fibers to characteristics of self compacting concrete (SCC). palm fibers self compacting concrete (PFSCC) is designed to have a dilute mixture, high strength (= 40 MPa), and have better precentage flexural strength. PFSCC was obtained from mixing of 85% cement, 15% fly ash, 1.5% superplastizicer, 0%, 0.5%, 1%, 1.5%, 2% and 3% palm fibers from the weight of binder  (cement + fly ash), water content 190 kg/m3, coarse aggregate 552.47 kg/m3 and sand 1,063 kg/m3. The more persentage palm fibers content added to the mixture makes workability of fresh concrete decreases. The best addition of palm fiber is 1%, this addition can increases the compressive strength 13% and flexural strength 1.8%.Keywords: self compacting concrete (SCC), fiber concrete, Palm fiber self compacting concrete (PFSCC), palm fiber

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

scholarly journals Effects of the Amount of Fly Ash Modified by Stearic Acid Compound on Mechanical Properties, Flame Retardant Ability, and Structure of the Composites

2020 ◽  
Vol 2020 ◽  
pp. 1-6 ◽  
Author(s):  
Tuan Anh Nguyen
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Stearic Acid ◽  
Flame Retardant ◽  
Burning Rate ◽  
Thermal Power ◽  
Waste Product ◽  
Fire Retardant

Fly ash, a waste product from thermal power plants, is one of the good alternatives for use as a filler in polymers, especially in flame retardants. Fly ash is an environmentally friendly fire retardant additive for composites, used in place of conventional flame retardant additives such as halogenated organic compounds, thus promoting environmental safety. In this study, fly ash was modified with stearic acid to improve adhesion at the polymers interface and increase compatibility. Fly ash was studied at various volumes (5, 10, and 20 wt.% fly ash) used in this study to synthesize fly ash-epoxy composites. The results show that the tensile strength, flexural strength, compressive strength, and impact strength of these synthetic materials increase when fly ash is modified to the surface, compressive strength: 197.87 MPa, flexural strength: 75.20 MPa, impact resistance: 5.77 KJ/m2, and tensile strength: 47.89 MPa. Especially, the fire retardant properties are improved at a high level, with a modified 20% fly ash content: the burning rate of 16.78 mm/min, minimum oxygen index of 23.2%, and meet the fire protection standard according to UL 94HB with a burning rate of 8.09 mm/min. Scanning electron microscopy (SEM) and infrared spectroscopy were used to analyze the morphological structure of fly ash after being modified and chemically bonded with epoxy resin background.

Effects of Fly Ash Addition on Compressive Strength and Flexural Strength of Foamed Cement Composites

2013 ◽  
Vol 795 ◽  
pp. 664-668 ◽  
Author(s):  
Roshasmawi Abdul Wahab ◽  
Mohd Noor Mazlee ◽  
Shamsul Baharin Jamaludin ◽  
Khairul Nizar Ismail
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Cement Composites ◽  
Volume Percent ◽  
Foaming Agent ◽  
Cement Ratio ◽  
Water To Cement Ratio

In this study, the mixing of polystyrene (PS) beads and fly ash as a sand replacement material in foamed cement composites (FCC) has been investigated. Specifically, the mechanical properties such as compressive strength and flexural strength were measured. Different proportions of fly ash were added in cement composites to replace the sand proportion at 3 wt. %, 6 wt. %, 9 wt. % and 12 wt. % respectively. The water to cement ratio was fixed at 0.65 meanwhile ratios of PS beads used was 0.25 volume percent of samples as a foaming agent. All samples at different mixed were cured at 7 and 28 days respectively. Based on the results of compressive strength, it was found that the compressive strength was increased with the increasing addition of fly ash. Meanwhile, flexural strength was decreased with the increasing addition of fly ash up to 9 wt. %. The foamed cement composites with 12 wt. % of fly ash produced the highest strength of compressive strength meanwhile 3 wt. % of fly ash produced the highest strength of flexural strength.

Influence of Foaming Agent on Properties of Red Mud Lightweight Baking-Free Brick

2014 ◽  
Vol 541-542 ◽  
pp. 388-391
Author(s):  
Long Ma ◽  
Guo Zhong Li
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Red Mud ◽  
Micro Structure ◽  
Foaming Agent ◽  
Scanning Electron

Red mud lightweight baking-free brick was prepared by red mud, fly ash and cement, mixed with a certain amount of activator agent and foaming agent. The influence of foaming agent on properties of red mud lightweight baking-free brick was studied. The micro-structure of red mud lightweight baking-free brick was characterized by scanning electron microscopy (SEM). The results show that when the foaming agent content is 10ml, the sample with better performance obtained and the density is 423kg/m3, flexural strength is 0.49MPa and compressive strength is 1.87MPa.

Sign in / Sign up

Export Citation Format

Share Document