DIN EN 60191-6-13:2017-06, Mechanische Normung von Halbleiterbauelementen_- Teil_6-13: Konstruktionsleitfaden für Open-top-Fassungen für Feinraster-Ball-Grid-Array und Feinraster-Land-Grid-Array (FBGA/FLGA) (IEC_60191-6-13:2016); Deutsche Fassung EN_60191-6-13:2016

2017 ◽  
Keyword(s):  
Ball Grid Array

Backside Application of Acoustic Micro Imaging (AMI) on Plastic Ball Grid Array (PBGA) and Plastic Quad Flat Pack (PQFP) Packages

2004 ◽  
Author(s):  
Luis A. Curiel ◽  
Andrew J. Komrowski ◽  
Daniel J.D. Sullivan
Keyword(s):  
Ball Grid Array ◽  
Acoustic Microscopy ◽  
Electronic Packages ◽  
Nondestructive Technique ◽  
Molding Compound ◽  
Microscopy Technique ◽  
Plastic Ball ◽  
Die Surface ◽  
Plastic Ball Grid Array ◽  
Bond Pads

Abstract Acoustic Micro Imaging (AMI) is an established nondestructive technique for evaluation of electronic packages. Non-destructive evaluation of electronic packages is often a critical first step in the Failure Analysis (FA) process of semiconductor devices [1]. The molding compound to die surface interface of the Plastic Ball Grid Array (PBGA) and Plastic Quad Flat Pack (PQFP) packages is an important interface to acquire for the FA process. Occasionally, with these packages, the standard acoustic microscopy technique fails to identify defects at the molding compound to die surface interface. The hard to identify defects are found at the edge of the die next to the bond pads or under the bonds wires. This paper will present a technique, Backside Acoustic Micro Imaging (BAMI) analysis, which can better resolve the molding compound to die surface interface at the die edge by sending the acoustic signal through the backside of the PBGA and PQFP packages.

The Effect of Ball Pad Metallurgy and Ball Composition on Solder Ball Integrity of Plastic Ball Grid Array Packages

1998 ◽  
Author(s):  
C.H. Zhong ◽  
Sung Yi
Keyword(s):  
Failure Mode ◽  
Barrier Layer ◽  
Shear Force ◽  
Solder Ball ◽  
Ball Grid Array ◽  
Reliability Test ◽  
Shear Forces ◽  
Ball Shear ◽  
Plastic Ball ◽  
Plastic Ball Grid Array

Abstract Ball shear forces of plastic ball grid array (PBGA) packages are found to decrease after reliability test. Packages with different ball pad metallurgy form different intermetallic compounds (IMC) thus ball shear forces and failure modes are different. The characteristic and dynamic process of IMC formed are decided by ball pad metallurgy which includes Ni barrier layer and Au layer thickness. Solder ball composition also affects IMC formation dynamic process. There is basically no difference in ball shear force and failure mode for packages with different under ball pad metallurgy before reliability test. However shear force decreased and failure mode changed after reliability test, especially when packages exposed to high temperature. Major difference in ball shear force and failure mode was found for ball pad metallurgy of Ni barrier layer including Ni-P, pure Ni and Ni-Co. Solder ball composition was found to affect the IMC formation rate.

Impact of the Ball Grid Array Connection Failures on Signal Integrity

2020 ◽  
Author(s):  
Kaixuan Song ◽  
Jinchun Gao ◽  
George T. Flowers ◽  
Ziren Wang ◽  
Qingya Li ◽  
...  
Keyword(s):  
Signal Integrity ◽  
Ball Grid Array

The Study of Underfill Epoxy Hardness in Reducing Curing Process Time for Flip Chip Packaging

2011 ◽  
Vol 462-463 ◽  
pp. 1194-1199
Author(s):  
Zainudin Kornain ◽  
Azman Jalar ◽  
Rozaidi Rashid ◽  
Shahrum Abdullah
Keyword(s):  
Thermal Expansion ◽  
Flip Chip ◽  
Ball Grid Array ◽  
Process Time ◽  
Curing Process ◽  
Curing Time ◽  
Hold Temperature ◽  
Flip Chip Packaging ◽  
Time Cycle ◽  
The Impact

Underfilling is the vital process to reduce the impact of the thermal stress that results from the mismatch in the co-efficient of thermal expansion (CTE) between the silicon chip and the substrate in Flip Chip Packaging. This paper reported the pattern of underfill’s hardness during curing process for large die Ceramic Flip Chip Ball Grid Array (FC-CBGA). A commercial amine based underfill epoxy was dispensed into HiCTE FC-CBGA and cured in curing oven under a new method of two-step curing profile. Nano-identation test was employed to investigate the hardness of underfill epoxy during curing steps. The result has shown the almost similar hardness of fillet area and centre of the package after cured which presented uniformity of curing states. The total curing time/cycle in production was potentially reduced due to no significant different of hardness after 60 min and 120 min during the period of second hold temperature.

Sign in / Sign up

Export Citation Format

Share Document