Leading Edge Vortex Development on a Pitching Flat Plate at Low Reynolds Number

2012 ◽  
Author(s):  
Adam Hart ◽  
Lawrence Ukeiley
Keyword(s):  
Reynolds Number ◽  
Flat Plate ◽  
Low Reynolds Number ◽  
Leading Edge ◽  
Leading Edge Vortex ◽  
Edge Vortex ◽  
Low Reynolds

scholarly journals Surging and plunging oscillations of an airfoil at low Reynolds number

2014 ◽  
Vol 763 ◽  
pp. 237-253 ◽  
Author(s):  
Jeesoon Choi ◽  
Tim Colonius ◽  
David R. Williams
Keyword(s):  
Reynolds Number ◽  
Low Reynolds Number ◽  
Leading Edge ◽  
Unsteady Motion ◽  
Flow Structures ◽  
Wake Instability ◽  
Edge Vortex ◽  
Vortex Shedding Frequency ◽  
The Mean ◽  
Low Reynolds

AbstractWe investigate the forces and unsteady flow structures associated with harmonic oscillations of an airfoil in the streamwise (surging) and transverse (plunging) directions in two-dimensional simulations at low Reynolds number. For the surging case, we show that there are specific frequencies where the wake instability synchronizes with the unsteady motion of the airfoil, leading to significant changes in the mean forces. Resonant behaviour of the time-averaged forces is observed near the vortex shedding frequency and its subharmonic; the behaviour is reminiscent of the dynamics of the generic nonlinear oscillator known as the Arnol’d tongue or the resonance horn. Below the wake instability frequency, there are two regimes where the fluctuating forces are amplified and attenuated, respectively. A detailed study of the flow structures associated with leading-edge vortex (LEV) growth and detachment are used to relate this behaviour with the LEV acting either in phase with the quasi-steady component of the forces for the amplification case, or out of phase for the attenuation case. Comparisons with wind tunnel measurements show that phenomenologically similar dynamics occur at higher Reynolds number. Finally, we show that qualitatively similar phenomena occur during both surging and plunging.

Heat Transfer and Flowfield Measurements in the Leading Edge Region of a Stator Vane Endwall

1999 ◽  
Vol 121 (3) ◽  
pp. 558-568 ◽  
Author(s):  
M. B. Kang ◽  
A. Kohli ◽  
K. A. Thole
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Edge Region ◽  
Leading Edge Vortex ◽  
Stator Vane ◽  
Edge Vortex ◽  
The Mean

The leading edge region of a first-stage stator vane experiences high heat transfer rates, especially near the endwall, making it very important to get a better understanding of the formation of the leading edge vortex. In order to improve numerical predictions of the complex endwall flow, benchmark quality experimental data are required. To this purpose, this study documents the endwall heat transfer and static pressure coefficient distribution of a modern stator vane for two different exit Reynolds numbers (Reex = 6 × 105 and 1.2 × 106). In addition, laser-Doppler velocimeter measurements of all three components of the mean and fluctuating velocities are presented for a plane in the leading edge region. Results indicate that the endwall heat transfer, pressure distribution, and flowfield characteristics change with Reynolds number. The endwall pressure distributions show that lower pressure coefficients occur at higher Reynolds numbers due to secondary flows. The stronger secondary flows cause enhanced heat transfer near the trailing edge of the vane at the higher Reynolds number. On the other hand, the mean velocity, turbulent kinetic energy, and vorticity results indicate that leading edge vortex is stronger and more turbulent at the lower Reynolds number. The Reynolds number also has an effect on the location of the separation point, which moves closer to the stator vane at lower Reynolds numbers.

Vortex Shedding Analysis in the Wake of a Flat Plate at Low Incidence and Low Reynolds Number

2021 ◽  
Author(s):  
Bastav Borah ◽  
Anand Verma ◽  
Vinayak Kulkarni ◽  
Ujjwal K. Saha
Keyword(s):  
Reynolds Number ◽  
Velocity Field ◽  
Flat Plate ◽  
Vortex Shedding ◽  
Low Reynolds Number ◽  
General Tendency ◽  
Flat Plates ◽  
Trailing Edge ◽  
Low Reynolds ◽  
Low Incidence

Abstract Vortex shedding phenomenon leads to a number of different features such as flow induced vibrations, fluid mixing, heat transfer and noise generation. With respect to aerodynamic application, the intensity of vortex shedding and the size of vortices play an essential role in the generation of lift and drag forces on an airfoil. The flat plates are known to have a better lift-to-drag ratio than conventional airfoils at low Reynolds number (Re). A better understanding of the shedding behavior will help aerodynamicists to implement flat plates at low Re specific applications such as fixed-wing micro air vehicle (MAV). In the present study, the shedding of vortices in the wake of a flat plate at low incidence has been studied experimentally in a low-speed subsonic wind tunnel at a Re of 5 × 104. The velocity field in the wake of the plate is measured using a hot wire anemometer. These measurements are taken at specific points in the wake across the flow direction and above the suction side of the flat plate. The velocity field is found to oscillate with one dominant frequency of fluctuation. The Strouhal number (St), calculated from this frequency, is computed for different angles of attack (AoA). The shedding frequency of vortices from the trailing edge of the flat plate has a general tendency to increase with AoA. In this paper, the generation and subsequent shedding of leading edge and trailing edge vortices in the wake of a flat plate are discussed.

Sign in / Sign up

Export Citation Format

Share Document