Maximum Mistuned Bladed Disk Forced Response with Frequency Veering

2004 ◽  
Author(s):  
James Kenyon
Keyword(s):  
Forced Response ◽  
Bladed Disk

A Method for Use of Cyclic Symmetry Properties in Analysis of Nonlinear Multiharmonic Vibrations of Bladed Disks

2004 ◽  
Vol 126 (1) ◽  
pp. 175-183 ◽  
Author(s):  
E. P. Petrov
Keyword(s):  
High Efficiency ◽  
Equations Of Motion ◽  
Linear Part ◽  
Forced Response ◽  
Mode Shapes ◽  
Solution Technique ◽  
Disk Model ◽  
Sector Model ◽  
Bladed Disk ◽  
Symmetry Properties

An effective method for analysis of periodic forced response of nonlinear cyclically symmetric structures has been developed. The method allows multiharmonic forced response to be calculated for a whole bladed disk using a periodic sector model without any loss of accuracy in calculations and modeling. A rigorous proof of the validity of the reduction of the whole nonlinear structure to a sector is provided. Types of bladed disk forcing for which the method may be applied are formulated. A multiharmonic formulation and a solution technique for equations of motion have been derived for two cases of description for a linear part of the bladed disk model: (i) using sector finite element matrices and (ii) using sector mode shapes and frequencies. Calculations validating the developed method and a numerical investigation of a realistic high-pressure turbine bladed disk with shrouds have demonstrated the high efficiency of the method.

The Effect of Non-Uniform Aerodynamic Loading on the Blade Responses

2007 ◽  
Author(s):  
Abdelgadir M. Mahmoud ◽  
Mohd S. Leong
Keyword(s):  
Turbine Blades ◽  
Forced Response ◽  
Flow Section ◽  
Flow Distortion ◽  
Inlet Flow ◽  
Bladed Disk ◽  
Aerodynamic Loading ◽  
Bladed Disk Assembly ◽  
Flow Generator ◽  
Inlet Flow Distortion

Turbine blades are always subjected to severe aerodynamic loading. The aerodynamic loading is uniform and Of harmonic nature. The harmonic nature depends on the rotor speed and number of nozzles (vanes counts). This harmonic loading is the main sources responsible for blade excitation. In some circumstances, the aerodynamic loading is not uniform and varies circumferentially. This paper discussed the effect of the non-uniform aerodynamic loading on the blade vibrational responses. The work involved the experimental study of forced response amplitude of model blades due to inlet flow distortion in the presence of airflow. This controlled inlet flow distortion therefore represents a nearly realistic environment involving rotating blades in the presence of airflow. A test rig was fabricated consisting of a rotating bladed disk assembly, an inlet flow section (where flow could be controlled or distorted in an incremental manner), flow conditioning module and an aerodynamic flow generator (air suction module with an intake fan) for investigations under laboratory conditions. Tests were undertaken for a combination of different air-flow velocities and blade rotational speeds. The experimental results showed that when the blades were subjected to unsteady aerodynamic loading, the responses of the blades increased and new frequencies were excited. The magnitude of the responses and the responses that corresponding to these new excited frequencies increased with the increase in the airflow velocity. Moreover, as the flow velocity increased the number of the newly excited frequency increased.

Experimental and Numerical Assessment of Mistuning Effects on Vibratory Response of a Bladed Disk with Underplatform Dampers

2021 ◽  
Author(s):  
S. Mehrdad Pourkiaee ◽  
Teresa Berruti ◽  
Stefano Zucca ◽  
Geoffrey Neuville
Keyword(s):  
Model Identification ◽  
Forced Response ◽  
Response Level ◽  
Static Test ◽  
Bladed Disk ◽  
Experimental Campaign ◽  
Proposed Model ◽  
Numerical Assessment ◽  
Linearized Model ◽  
Forced Responses

Abstract This paper presents experimental and numerical investigation of mistuned forced responses of an integrally bladed disk with full set of underplatform dampers (UPDs). This research aims at providing: 1. An experimental benchmark for nonlinear dynamics of a mistuned bladed disks with UPDs. 2. A numerical model that can account for features of a mistuned forced response level. Accordingly, a detailed experimental campaign is conducted on a static test rig called Octopus. This rig is specifically designed to investigate the dynamics of a full-scale integrally bladed disk (blisk) with UPDs in a noncontact manner so that the dynamic response of the system is not modified. The effect of mistuning on experimental forced response levels is assessed and a linearized model is proposed to predict the modulation of frequency response functions (FRFs) due to the frequency splitting. In the development of the model, the mistuning pattern identified from the linear blisk without UPDs is used and it is assumed that adding the dampers does not change the structural mistuning of the blisk. In this study, the fundamental mistuning model identification (FMM ID) was employed to identify the mistuning pattern of the blisk. It is shown that the proposed model successfully predicts the modulation of linear mistuned FRFs. The linearized model is also able to predict the modulation of nonlinear mistuned FRFs in stick condition (when nonlinear friction damping is negligible) with a good accuracy validating this assumption that adding the dampers does not change the mistuning pattern.

Blade Root Joint Modelling and Analysis of Effects of Their Geometry Variability on the Nonlinear Forced Response of Tuned and Mistuned Bladed Disks

2020 ◽  
Author(s):  
Adam Koscso ◽  
E. P. Petrov
Keyword(s):  
Harmonic Balance Method ◽  
Forced Response ◽  
High Fidelity ◽  
Contact Interactions ◽  
Bladed Disks ◽  
Element Mesh ◽  
Disk Model ◽  
Bladed Disk ◽  
Nonlinear Contact ◽  
Manufacturing Tolerances

Abstract One of the major sources of the damping of the forced vibration for bladed disk structures is the micro-slip motion at the contact interfaces of blade-disk joints. In this paper, the modeling strategies of nonlinear contact interactions at blade roots are examined using high-fidelity modelling of bladed disk assemblies and the nonlinear contact interactions at blade-disk contact patches. The analysis is performed in the frequency domain using multiharmonic harmonic balance method and analytically formulated node-to-node contact elements modelling frictional and gap nonlinear interactions. The effect of the number, location and distribution of nonlinear contact elements are analyzed using cyclically symmetric bladed disks. The possibility of using the number of the contact elements noticeably smaller than the total number of nodes in the finite element mesh created at the contact interface for the high-fidelity bladed disk model is demonstrated. The parameters for the modeling of the root damping are analysed for tuned and mistuned bladed disks. The geometric shapes of blade roots and corresponding slots in disks cannot be manufactured perfectly and there is inevitable root joint geometry variability within the manufacturing tolerances. Based on these tolerances, the extreme cases of the geometry variation are defined and the assessment of the possible effects of the root geometry variation on the nonlinear forced response are performed based on a set of these extreme cases.

The Combined Closed Form-Perturbation Approach to the Analysis of Mistuned Bladed Disks

1993 ◽  
Vol 115 (4) ◽  
pp. 771-780 ◽  
Author(s):  
M. P. Mignolet ◽  
C.-C. Lin
Keyword(s):  
Probability Density Function ◽  
Probability Density ◽  
Density Function ◽  
Approximate Solutions ◽  
Forced Response ◽  
Perturbation Approach ◽  
Perturbation Techniques ◽  
Step Method ◽  
Bladed Disk

A two-step method is presented for the determination of reliable approximations of the probability density function of the forced response of a randomly mistuned bladed disk. Under the assumption of linearity, an integral representation of the probability density function of the blade amplitude is first derived. Then, deterministic perturbation techniques are employed to produce simple approximations of this function. The adequacy of the method is demonstrated by comparing several approximate solutions with simulation results.

Parametric Dynamics of Mistuned Bladed Disk

2014 ◽  
Author(s):  
Peiyi Wang ◽  
Lin Li
Keyword(s):  
Coupling Strength ◽  
Amplification Factor ◽  
Dynamic Properties ◽  
Forced Response ◽  
Design Parameters ◽  
Classical Dynamic ◽  
Mode Localization ◽  
Bladed Disk ◽  
Saddle Surface ◽  
Wear And Tear

The mistuning of bladed disk comes from manufacturing tolerances and in-service wear and tear. Consequently the cyclic symmetry has been destroyed by mistuning, even small mistuning levels could result in drastic changes in the dynamics of bladed disks. Specifically, mistuning can cause mode localization and an increase of the maximum forced response. It has been known that frequency veering, modal localization and magnification of response are three most classical dynamic properties of bladed disk. However few researches has focused on the relationships between dynamic characters and design parameters, because the proper variation ranges of the design parameters are difficult to be determined. The aim of this paper is to investigate the relationship between designed parameters and dynamic properties of mistuned bladed disk. Based on a lumped parametric model of bladed disk and utilizing parameterized eigenvalue solution, a reasonable range of designed parameter corresponding to specific nodal diameter index was provided. The numerical results showed that the curves of the gap of frequency veering versus coupling strength or blade stiffness have bowel-style. It was also found that there exists a quasi-saddle-surface while the vibration amplification factor varies with coupling strength and mistuning strength. The quasi-saddle-surface reveals that the existence of threshold of vibration amplification factor depends on the value of coupling strength. The result means that a proper choice of combination of coupling strength and mistuning strength could lead to a suppression of mistuned vibration amplification.

Investigation of Damping Potential of Strip Damper on a Real Turbine Blade

2016 ◽  
Author(s):  
M. Afzal ◽  
I. Lopez Arteaga ◽  
L. Kari ◽  
V. Kharyton
Keyword(s):  
Boundary Conditions ◽  
Dynamic Properties ◽  
Equations Of Motion ◽  
Iterative Solution ◽  
Element Model ◽  
Forced Response ◽  
Contact Forces ◽  
Response Analysis ◽  
Bladed Disk ◽  
Different Types

This paper investigates the damping potential of strip dampers on a real turbine bladed disk. A 3D numerical friction contact model is used to compute the contact forces by means of the Alternate Frequency Time domain method. The Jacobian matrix required during the iterative solution is computed in parallel with the contact forces, by a quasi-analytical method. A finite element model of the strip dampers, that allows for an accurate description of their dynamic properties, is included in the steady-state forced response analysis of the bladed disk. Cyclic symmetry boundary conditions and the multiharmonic balance method are applied in the formulation of the equations of motion in the frequency domain. The nonlinear forced response analysis is performed with two different types of boundary conditions on the strip: (a) free-free and (b) elastic, and their influence is analyzed. The effect of the strip mass, thickness and the excitation levels on the forced response curve is investigated in detail.

The Interaction Between Mistuning and Friction in the Forced Response of Bladed Disk Assemblies

1985 ◽  
Vol 107 (1) ◽  
pp. 205-211 ◽  
Author(s):  
J. H. Griffin ◽  
A. Sinha
Keyword(s):  
Gas Turbine ◽  
Turbine Blades ◽  
Forced Response ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Resonant Response ◽  
Friction Dampers ◽  
Bladed Disk ◽  
The Impact ◽  
Slip Force

This paper summarizes the results of an investigation to establish the impact of mistuning on the performance and design of blade-to-blade friction dampers of the type used to control the resonant response of turbine blades in gas turbine engines. In addition, it discusses the importance of friction slip force variations on the dynamic response of shrouded fan blades.

Alternate Mistuning of Turbine Bladings Coupled by Underplatform Dampers

2012 ◽  
Author(s):  
S. Tatzko ◽  
L. Panning-von Scheidt ◽  
J. Wallaschek ◽  
A. Kayser
Keyword(s):  
Turbine Blades ◽  
Steady State Solution ◽  
Computational Effort ◽  
Forced Response ◽  
Nonlinear Coupling ◽  
Cyclic Symmetry ◽  
Periodic Excitation ◽  
Blade Vibration ◽  
Mode Localization ◽  
Bladed Disk

In turbo machinery design it is important to avoid vibrations that can destroy the turbine in the last resort. The rotating structure is exposed to periodic excitation forces. Two main types of periodic excitation can be distinguished. Flutter is the effect when mass flow forces couple with a natural vibration mode. The result is a negative damping coefficient and amplitudes will rise up to malfunction of the structure. The engine order excitation is a periodic excitation where the force signal is directly related to the speed of the rotor. A forced response calculation gives information about the blade vibration. Nonlinear coupling, i.e. friction coupling, between blades is used to increase damping of the bladed disk. Dynamic analysis of turbine blades with nonlinear coupling is a complex task and computer simulations are inevitable. Various techniques have been developed to reduce computational effort. The cyclic symmetry approach assumes each blade around the disk to be identical. Thus only one sector of the disk is sufficient to compute the steady state solution of the whole turbine blading. However, it has been observed that mistuning of blades reduces the flutter instability. On the other hand statistical mistuning can lead to dangerously high forced response amplitudes due to mode localization. A compromise is intentional mistuning. The simplest approach is alternate mistuning with every other blade exhibiting identical mechanical properties. This work explains in detail how a turbine bladed disk can be modeled when alternate mistuning is applied intentionally. Cyclic symmetry is used and each sector comprises two blades. This untypical choice of the sector size has significant impact on results of a cyclic modal analysis. Simulation results show the influence of alternate mistuned turbine bladings which are coupled by underplatform damper elements.

Transient Forced Response Analysis of Mistuned Steam Turbine Blades During Startup and Coastdown

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Christian Siewert ◽  
Heinrich Stüer
Keyword(s):  
Mechanical Model ◽  
Turbine Blades ◽  
Forced Vibrations ◽  
Forced Response ◽  
The Self ◽  
Response Analysis ◽  
Computationally Efficient ◽  
Bladed Disk ◽  
Steam Turbine Blades ◽  
Number Of Publications

It is well known that the vibrational behavior of a mistuned bladed disk differs strongly from that of a tuned bladed disk. A large number of publications dealing with the dynamics of mistuned bladed disks are available in the literature. The vibrational phenomena analyzed in these publications are either forced vibrations or self-excited flutter vibrations. Nearly, all published literature on the forced vibrations of mistuned blades disks considers harmonic, i.e., steady-state, vibrations, whereas the self-excited flutter vibrations are analyzed by the evaluation of the margin against instabilities by means of a modal, or rather than eigenvalue, analysis. The transient forced response of mistuned bladed disk is not analyzed in detail so far. In this paper, a computationally efficient mechanical model of a mistuned bladed disk to compute the transient forced response is presented. This model is based on the well-known fundamental model of mistuning (FMM). With this model, the statistics of the transient forced response of a mistuned bladed disk is analyzed and compared to the results of harmonic forced response analysis.

Sign in / Sign up

Export Citation Format

Share Document