scholarly journals Blade surface pressure distributions in a rocket engine turbine - Experimental work with on-blade pressure transducers

2000 ◽  
Author(s):  
Susan Hudson ◽  
Thomas Zoladz ◽  
Lisa Griffin
Keyword(s):  
Surface Pressure ◽  
Experimental Work ◽  
Rocket Engine ◽  
Blade Surface ◽  
Pressure Transducers ◽  
Pressure Distributions

scholarly journals Rocket Engine Turbine Blade Surface Pressure Distributions: Experiment and Computations

2003 ◽  
Vol 19 (3) ◽  
pp. 364-373 ◽  
Author(s):  
Susan T. Hudson ◽  
Thomas F. Zoladz ◽  
Daniel J. Dorney
Keyword(s):  
Turbine Blade ◽  
Surface Pressure ◽  
Rocket Engine ◽  
Blade Surface ◽  
Pressure Distributions

Time-Averaged Heat Transfer and Pressure Measurements and Comparison With Prediction for a Two-Stage Turbine

1994 ◽  
Vol 116 (1) ◽  
pp. 14-22 ◽  
Author(s):  
M. G. Dunn ◽  
J. Kim ◽  
K. C. Civinskas ◽  
R. J. Boyle
Keyword(s):  
Surface Pressure ◽  
Space Shuttle ◽  
Three Dimensional ◽  
Stanton Number ◽  
Navier Stokes ◽  
Pressure Measurements ◽  
Two Stage ◽  
Pressure Transducers ◽  
Pressure Distributions ◽  
Main Engine

Time-averaged Stanton number and surface-pressure distributions are reported for the first-stage vane row and the first-stage blade row of the Rocketdyne Space Shuttle Main Engine two-stage fuel-side turbine. These measurements were made at 10, 50, and 90 percent span on both the pressure and suction surfaces of the component. Stanton-number distributions are also reported for the second-stage vane at 50 percent span. A shock tube is used as a short-duration source of heated and pressurized air to which the turbine is subjected. Platinum thin-film gages are used to obtain the heat-flux measurements and miniature silicone-diaphragm pressure transducers are used to obtain the surface pressure measurements. The first-stage vane Stanton number distributions are compared with predictions obtained using a quasi-three dimensional Navier–Stokes solution and a version of STAN5. This same N–S technique was also used to obtain predictions for the first blade and the second vane.

Surface Pressure Distribution on a Blade of a 10 m Diameter HAWT (Field Measurements versus Wind Tunnel Measurements)

2005 ◽  
Vol 127 (2) ◽  
pp. 185-191 ◽  
Author(s):  
T. Maeda ◽  
E. Ismaili ◽  
H. Kawabuchi ◽  
Y. Kamada
Keyword(s):  
Wind Tunnel ◽  
Surface Pressure ◽  
Field Measurements ◽  
Reynolds Numbers ◽  
Blade Surface ◽  
Pressure Data ◽  
Surface Pressure Distribution ◽  
Pressure Distributions ◽  
Wind Tunnel Data ◽  
Local Angle

This paper exploits blade surface pressure data acquired by testing a three-bladed upwind turbine operating in the field. Data were collected for a rotor blade at spanwise 0.7R with the rotor disc at zero yaw. Then, for the same blade, surface pressure data were acquired by testing in a wind tunnel. Analyses compared aerodynamic forces and surface pressure distributions under field conditions against analogous baseline data acquired from the wind tunnel data. The results show that aerodynamic performance of the section 70%, for local angle of attack below static stall, is similar for free stream and wind tunnel conditions and resemblances those commonly observed on two-dimensional aerofoils near stall. For post-stall flow, it is presumed that the exhibited differences are attributes of the differences on the Reynolds numbers at which the experiments were conducted.

System to Measure the Pressure Distribution on Fan Aerofoil Surfaces During Flutter Conditions

1980 ◽  
Vol 102 (4) ◽  
pp. 427-432
Author(s):  
John W. H. Chivers
Keyword(s):  
Surface Pressure ◽  
High Speed ◽  
Cross Correlation ◽  
Test Results ◽  
Blade Surface ◽  
Pressure Data ◽  
Pressure Transducers ◽  
Induced Stress ◽  
Blade Tip ◽  
Typical Test

In order to assist in the understanding of high speed flutter, a series of tests has been conducted on a research fan in which the blade surface pressures have been measured by means of miniature silicon diaphragm pressure transducers embedded in selected fan blades. Prior to this investigation a program of rig tests was conducted to examine the effects of centrifugal force and vibration on the transducer performance and a transducer mounting technique was developed to minimize blade induced stress in the transducer. Instantaneous measurements of the tip stagger angles of the pressure instrumented fan blades have enabled a cross correlation to be performed on the blade surface pressure data and the blade tip angles. Some typical test results are shown.

scholarly journals Unsteady Pressure Measurements in a Rotating Centrifugal Impeller

1992 ◽  
Author(s):  
G. Roth
Keyword(s):  
Surface Pressure ◽  
Suction Side ◽  
Rotating Stall ◽  
Centrifugal Impeller ◽  
Pressure Measurements ◽  
Blade Surface ◽  
Pressure Transducers ◽  
Engine Order ◽  
Analysis Technique ◽  
Stable Operating

The design of a shrouded radial test impeller which enables the application of miniature pressure transducers inside the blades is presented. An explanation of the measurement and analysis technique is given. The results of suction side blade surface pressure measurements at several points of a performance line are presented. Two different types of diffuser rotating stall were detected. The pressure behaviour at impeller stall and surge inception is demonstrated. Furthermore, the periodic engine order blade surface pressure signals at a stable operating point are shown.

Structures and Interactions Underlying Rotational Augmentation of Blade Aerodynamic Response

2003 ◽  
Author(s):  
S. Schreck ◽  
M. Robinson
Keyword(s):  
Surface Pressure ◽  
Normal Force ◽  
Unsteady Aerodynamics ◽  
Boundary Layer Separation ◽  
Time Dependent ◽  
Blade Surface ◽  
Pressure Data ◽  
Pressure Distributions ◽  
Standard Deviations ◽  
Tunnel Time

Blade rotation routinely and significantly augments aerodynamic forces during zero yaw HAWT operation. To better understand the flow physics underlying this phenomenon, time dependent blade surface pressure data were acquired from the NREL Unsteady Aerodynamics Experiment, a full-scale HAWT tested in the NASA Ames 80 ft × 120 Ft wind tunnel. Time records of surface pressures and normal force were processed to obtain means and standard deviations. Surface pressure means and standard deviations were analyzed to identify boundary layer separation and reattachment locations. Separation and reattachment kinematics were then correlated with normal force behavior. Results showed that rotational augmentation was linked to specific separation and reattachment behaviors, and to associated three-dimensionality in surface pressure distributions.

Time-Averaged Heat Transfer and Pressure Measurements and Comparison With Prediction for a Two-Stage Turbine

1992 ◽  
Author(s):  
M. G. Dunn ◽  
J. Kim ◽  
K. C. Civinskas ◽  
R. J. Boyle
Keyword(s):  
Surface Pressure ◽  
Space Shuttle ◽  
Stanton Number ◽  
Navier Stokes ◽  
Pressure Measurements ◽  
Two Stage ◽  
Pressure Transducers ◽  
Pressure Distributions ◽  
Flux Measurements ◽  
Main Engine

Time-averaged Stanton number and surface-pressure distributions are reported for the first-stage vane row and the first-stage blade row of the Rocketdyne Space Shuttle Main Engine two-stage fuel-side turbine. These measurements were made at 10%, 50%, and 90% span on both the pressure and suction surfaces of the component. Stanton-number distributions are also reported for the second-stage vane at 50% span. A shock tube is used as a short-duration source of heated and pressurized air to which the turbine is subjected. Platinum thin-film pages are used to obtain the heat-flux measurements and miniature silicone-diaphragm pressure transducers are used to obtain the surface pressure measurements. The first-stage vane Stanton number distributions are compared with predictions obtained using a quasi-3D Navier-Stokes solution and a version of STAN5. This same N-S technique was also used to obtain predictions for the first blade and the second vane.

Three Dimensional Unsteady Pressure Measurements for an Oscillating Turbine Blade

1997 ◽  
Author(s):  
D. L. Bell ◽  
L. He
Keyword(s):  
Turbine Blade ◽  
Surface Pressure ◽  
Three Dimensional ◽  
Test Facility ◽  
Pressure Measurements ◽  
Blade Surface ◽  
Low Speed ◽  
Pressure Transducers ◽  
Bending Mode ◽  
Oscillation Frequencies

A complete set of unsteady blade surface pressure measurements is presented for a single turbine blade oscillating in a three dimensional bending mode. Results are provided for five spanwise sections at 10%, 30%, 50%, 70% and 90% of span. Steady blade pressure measurements and five-hole probe traverses at the inlet and exit planes of the test section, are also included. The test facility operates at low speed and the working section consists of a single turbine blade mounted in a profiled duct. A rigid blade with constant section was used, and a three dimensional bending mode realised by hinging the blade at root and driving the tip section. The low speed and scale of the test facility allowed low oscillation frequencies (5 to 20 Hz) to be employed, in order to match realistic reduced frequencies. This enabled the unsteady blade surface pressure response to be recorded with externally mounted pressure transducers. The validity of this technique is examined. Results from the test facility demonstrate a noticeable three dimensional behaviour of the unsteady flow.

Sign in / Sign up

Export Citation Format

Share Document