System to Measure the Pressure Distribution on Fan Aerofoil Surfaces During Flutter Conditions

1980 ◽  
Vol 102 (4) ◽  
pp. 427-432
Author(s):  
John W. H. Chivers
Keyword(s):  
Surface Pressure ◽  
High Speed ◽  
Cross Correlation ◽  
Test Results ◽  
Blade Surface ◽  
Pressure Data ◽  
Pressure Transducers ◽  
Induced Stress ◽  
Blade Tip ◽  
Typical Test

In order to assist in the understanding of high speed flutter, a series of tests has been conducted on a research fan in which the blade surface pressures have been measured by means of miniature silicon diaphragm pressure transducers embedded in selected fan blades. Prior to this investigation a program of rig tests was conducted to examine the effects of centrifugal force and vibration on the transducer performance and a transducer mounting technique was developed to minimize blade induced stress in the transducer. Instantaneous measurements of the tip stagger angles of the pressure instrumented fan blades have enabled a cross correlation to be performed on the blade surface pressure data and the blade tip angles. Some typical test results are shown.

Surface Pressure Distribution on a Blade of a 10 m Diameter HAWT (Field Measurements versus Wind Tunnel Measurements)

2005 ◽  
Vol 127 (2) ◽  
pp. 185-191 ◽  
Author(s):  
T. Maeda ◽  
E. Ismaili ◽  
H. Kawabuchi ◽  
Y. Kamada
Keyword(s):  
Wind Tunnel ◽  
Surface Pressure ◽  
Field Measurements ◽  
Reynolds Numbers ◽  
Blade Surface ◽  
Pressure Data ◽  
Surface Pressure Distribution ◽  
Pressure Distributions ◽  
Wind Tunnel Data ◽  
Local Angle

This paper exploits blade surface pressure data acquired by testing a three-bladed upwind turbine operating in the field. Data were collected for a rotor blade at spanwise 0.7R with the rotor disc at zero yaw. Then, for the same blade, surface pressure data were acquired by testing in a wind tunnel. Analyses compared aerodynamic forces and surface pressure distributions under field conditions against analogous baseline data acquired from the wind tunnel data. The results show that aerodynamic performance of the section 70%, for local angle of attack below static stall, is similar for free stream and wind tunnel conditions and resemblances those commonly observed on two-dimensional aerofoils near stall. For post-stall flow, it is presumed that the exhibited differences are attributes of the differences on the Reynolds numbers at which the experiments were conducted.

A Novel Approach to Surge Control: High-Frequency Pressure Variance As an Indicator of Impending Surge in Centrifugal Compressors

2018 ◽  
Author(s):  
Meera Day Towler ◽  
Tim Allison ◽  
Paul Krueger ◽  
Karl Wygant
Keyword(s):  
High Speed ◽  
Fast Response ◽  
Time Signal ◽  
Multiple Time ◽  
Pressure Data ◽  
Pressure Transducers ◽  
Surge Margin ◽  
Novel Approach ◽  
Surge Control ◽  
Response Pressure

This investigation studies fast-response pressure measurements as an indicator of the onset of surge in a single-stage centrifugal compressor. The objective is to determine an online monitoring approach for surge control that does not rely on surge margin relative to maps from predictions or factory testing. Fast-response pressure transducers are installed in the suction piping, inducer, diffuser, and discharge piping. A speed line is mapped, and high-speed pressure data are collected across the compressor map. The compressor is driven into surge several times to collect pressure data between during surge and between surge events. Following testing, these data are post-processed via filtration and statistical analyses. It is determined that, when taken together, the mean and range of the standard deviation of the time signal for multiple time steps can be used to determine whether the compressor’s operating point is approaching surge for the conditions tested.

Time-Averaged and Time-Accurate Aero-Dynamics for the Recessed Tip Cavity of a High-Pressure Turbine Blade and the Outer Stationary Shroud: Comparison of Computational and Experimental Results

2004 ◽  
Author(s):  
Brian R. Green ◽  
John W. Barter ◽  
Charles W. Haldeman ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Turbine Blade ◽  
Computational Models ◽  
Turbine Rotor ◽  
Single Stage ◽  
Cfd Modeling ◽  
Blade Surface ◽  
High Pressure Turbine ◽  
Pressure Transducers ◽  
Blade Tip

The unsteady aero-dynamics of a single-stage high-pressure turbine blade operating at design corrected conditions has been the subject of a thorough study involving detailed measurements and computations. The experimental configuration consisted of a single-stage high-pressure turbine and the adjacent, downstream, low-pressure turbine nozzle row. All three blade-rows were instrumented at three spanwise locations with flush-mounted, high frequency response pressure transducers. The rotor was also instrumented with the same transducers on the blade tip and platform and the stationary shroud was instrumented with pressure transducers at specific locations above the rotating blade. Predictions of the time-dependent flow field around the rotor were obtained using MSU-TURBO, a 3D, non-linear, computational fluid dynamics (CFD) code. Using an isolated blade-row unsteady analysis method, the unsteady surface pressure for the high-pressure turbine rotor due to the upstream high-pressure turbine nozzle was calculated. The predicted unsteady pressure on the rotor surface was compared to the measurements at selected spanwise locations on the blade, in the recessed cavity, and on the shroud. The rig and computational models included a flat and recessed blade tip geometry and were used for the comparisons presented in the paper. Comparisons of the measured and predicted static pressure loading on the blade surface show excellent correlation from both a time-average and time-accurate standpoint. This paper concentrates on the tip and shroud comparisons between the experiments and the predictions and these results also show good correlation with the time-resolved data. These data comparisons provide confidence in the CFD modeling and its ability to capture unsteady flow physics on the blade surface, in the flat and recessed tip regions of the blade, and on the stationary shroud.

scholarly journals Unsteady Pressure Measurements in a Rotating Centrifugal Impeller

1992 ◽  
Author(s):  
G. Roth
Keyword(s):  
Surface Pressure ◽  
Suction Side ◽  
Rotating Stall ◽  
Centrifugal Impeller ◽  
Pressure Measurements ◽  
Blade Surface ◽  
Pressure Transducers ◽  
Engine Order ◽  
Analysis Technique ◽  
Stable Operating

The design of a shrouded radial test impeller which enables the application of miniature pressure transducers inside the blades is presented. An explanation of the measurement and analysis technique is given. The results of suction side blade surface pressure measurements at several points of a performance line are presented. Two different types of diffuser rotating stall were detected. The pressure behaviour at impeller stall and surge inception is demonstrated. Furthermore, the periodic engine order blade surface pressure signals at a stable operating point are shown.

Structures and Interactions Underlying Rotational Augmentation of Blade Aerodynamic Response

2003 ◽  
Author(s):  
S. Schreck ◽  
M. Robinson
Keyword(s):  
Surface Pressure ◽  
Normal Force ◽  
Unsteady Aerodynamics ◽  
Boundary Layer Separation ◽  
Time Dependent ◽  
Blade Surface ◽  
Pressure Data ◽  
Pressure Distributions ◽  
Standard Deviations ◽  
Tunnel Time

Blade rotation routinely and significantly augments aerodynamic forces during zero yaw HAWT operation. To better understand the flow physics underlying this phenomenon, time dependent blade surface pressure data were acquired from the NREL Unsteady Aerodynamics Experiment, a full-scale HAWT tested in the NASA Ames 80 ft × 120 Ft wind tunnel. Time records of surface pressures and normal force were processed to obtain means and standard deviations. Surface pressure means and standard deviations were analyzed to identify boundary layer separation and reattachment locations. Separation and reattachment kinematics were then correlated with normal force behavior. Results showed that rotational augmentation was linked to specific separation and reattachment behaviors, and to associated three-dimensionality in surface pressure distributions.

Averaged and Time-Dependent Aerodynamics of a High Pressure Turbine Blade Tip Cavity and Stationary Shroud: Comparison of Computational and Experimental Results

2004 ◽  
Vol 127 (4) ◽  
pp. 736-746 ◽  
Author(s):  
Brian R. Green ◽  
John W. Barter ◽  
Charles W. Haldeman ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Turbine Blade ◽  
Computational Models ◽  
Single Stage ◽  
Time Dependent ◽  
Cfd Modeling ◽  
Blade Surface ◽  
High Pressure Turbine ◽  
Pressure Transducers ◽  
Blade Tip

The unsteady aero-dynamics of a single-stage high-pressure turbine blade operating at design corrected conditions has been the subject of a thorough study involving detailed measurements and computations. The experimental configuration consisted of a single-stage high-pressure turbine and the adjacent, downstream, low-pressure turbine nozzle row. All three blade-rows were instrumented at three spanwise locations with flush-mounted, high-frequency response pressure transducers. The rotor was also instrumented with the same transducers on the blade tip and platform and the stationary shroud was instrumented with pressure transducers at specific locations above the rotating blade. Predictions of the time-dependent flow field around the rotor were obtained using MSU-TURBO, a three-dimensional (3D), nonlinear, computational fluid dynamics (CFD) code. Using an isolated blade-row unsteady analysis method, the unsteady surface pressure for the high-pressure turbine rotor due to the upstream high-pressure turbine nozzle was calculated. The predicted unsteady pressure on the rotor surface was compared to the measurements at selected spanwise locations on the blade, in the recessed cavity, and on the shroud. The rig and computational models included a flat and recessed blade tip geometry and were used for the comparisons presented in the paper. Comparisons of the measured and predicted static pressure loading on the blade surface show excellent correlation from both a time-average and time-accurate standpoint. This paper concentrates on the tip and shroud comparisons between the experiments and the predictions and these results also show good correlation with the time-resolved data. These data comparisons provide confidence in the CFD modeling and its ability to capture unsteady flow physics on the blade surface, in the flat and recessed tip regions of the blade, and on the stationary shroud.

Three Dimensional Unsteady Pressure Measurements for an Oscillating Turbine Blade

1997 ◽  
Author(s):  
D. L. Bell ◽  
L. He
Keyword(s):  
Turbine Blade ◽  
Surface Pressure ◽  
Three Dimensional ◽  
Test Facility ◽  
Pressure Measurements ◽  
Blade Surface ◽  
Low Speed ◽  
Pressure Transducers ◽  
Bending Mode ◽  
Oscillation Frequencies

A complete set of unsteady blade surface pressure measurements is presented for a single turbine blade oscillating in a three dimensional bending mode. Results are provided for five spanwise sections at 10%, 30%, 50%, 70% and 90% of span. Steady blade pressure measurements and five-hole probe traverses at the inlet and exit planes of the test section, are also included. The test facility operates at low speed and the working section consists of a single turbine blade mounted in a profiled duct. A rigid blade with constant section was used, and a three dimensional bending mode realised by hinging the blade at root and driving the tip section. The low speed and scale of the test facility allowed low oscillation frequencies (5 to 20 Hz) to be employed, in order to match realistic reduced frequencies. This enabled the unsteady blade surface pressure response to be recorded with externally mounted pressure transducers. The validity of this technique is examined. Results from the test facility demonstrate a noticeable three dimensional behaviour of the unsteady flow.

Pressure-Sensitive Paint Investigation for Turbomachinery Application

1995 ◽  
Author(s):  
K. Sabroske ◽  
D. Rabe ◽  
C. Williams
Keyword(s):  
Surface Pressure ◽  
Rotor Blade ◽  
Ccd Camera ◽  
Pressure Sensitive Paint ◽  
Blade Surface ◽  
Pressure Data ◽  
Operational Environment ◽  
Suction Surface ◽  
Transonic Compressor ◽  
Pressure Sensitive

Two preliminary tests are discussed which investigate the feasibility of using pressure-sensitive paint (PSP) technology to acquire blade surface pressures in turbomachinery. The first test determined the prospect of using PSP in an operational environment. In this test, PSP was applied to a first stage rotor blade of a state-of-the-art transonic compressor. The paint survived the normal operating temperature, pressure, and centrifugal forces present in this compressor at rotational speeds up to 13,000 RPM. The second test investigated techniques to acquire blade surface pressure data. Suction surface intensity measurements were acquired from a low speed, high-aspect ratio compressor using a back illuminated charge coupled device (CCD) camera while the compressor was rotating at 1500 RPM. An optical derotating mechanism was used to hold the rotor blade image stationary while acquiring PSP data. Both experiments demonstrate that PSP is a viable technique to acquire blade surface pressure data in full scale compressor testing. Special considerations required in applying PSP techniques to turbomachinery are also reported.

High-Speed Noncontacting Instrumentation for Jet Engine Testing

1980 ◽  
Vol 102 (4) ◽  
pp. 912-917 ◽  
Author(s):  
M. J. Scotto ◽  
M. E. Eismeier
Keyword(s):  
Experimental Data ◽  
High Speed ◽  
Tip Clearance ◽  
Jet Engines ◽  
Blade Surface ◽  
Operating Characteristics ◽  
Jet Engine ◽  
Blade Tip ◽  
Engine Testing ◽  
Blade Tip Clearance

This paper discusses high-speed, noncontacting instrumentation systems for measuring the operating characteristics of jet engines. The discussion includes optical pyrometers for measuring blade surface temperatures, capacitance clearanceometers for measuring blade tip clearance and vibration, and optoelectronic systems for measuring blade flex and torsion. In addition, engine characteristics that mandate the use of such unique instrumentation are pointed out as well as the shortcomings of conventional noncontacting devices. Experimental data taken during engine testing are presented and recommendations for future development discussed.

Sign in / Sign up

Export Citation Format

Share Document