Development of generalized process models for superplastic forming of titanium structures

1985 ◽  
Author(s):  
D. BHATT
Keyword(s):  
Superplastic Forming ◽  
Process Models

Identifying suboptimalities with factorial model comparison

2018 ◽  
Vol 41 ◽  
Author(s):  
Wei Ji Ma
Keyword(s):  
Experimental Design ◽  
Model Comparison ◽  
Process Models ◽  
Multiple Forms ◽  
Factorial Experimental Design ◽  
Factorial Model ◽  
Multiple Components ◽  
The Many

AbstractGiven the many types of suboptimality in perception, I ask how one should test for multiple forms of suboptimality at the same time – or, more generally, how one should compare process models that can differ in any or all of the multiple components. In analogy to factorial experimental design, I advocate for factorial model comparison.

A very rapid in situ Kikuchi technique to determine relative crystal misorientation

1988 ◽  
Vol 46 ◽  
pp. 830-831
Author(s):  
J. I. Bennetch
Keyword(s):  
Electron Beam ◽  
Analytical Techniques ◽  
Superplastic Forming ◽  
The Other ◽  
Kikuchi Pattern ◽  
Kikuchi Line ◽  
Line Analysis

In a recent study of the superplastic forming (SPF) behavior of certain Al-Li-X alloys, the relative misorientation between adjacent (sub)grains proved to be an important parameter. It is well established that the most accurate way to determine misorientation across boundaries is by Kikuchi line analysis. However, the SPF study required the characterization of a large number of (sub)grains in each sample to be statistically meaningful, a very time-consuming task even for comparatively rapid Kikuchi analytical techniques.In order to circumvent this problem, an alternate, even more rapid in-situ Kikuchi technique was devised, eliminating the need for the developing of negatives and any subsequent measurements on photographic plates. All that is required is a double tilt low backlash goniometer capable of tilting ± 45° in one axis and ± 30° in the other axis. The procedure is as follows. While viewing the microscope screen, one merely tilts the specimen until a standard recognizable reference Kikuchi pattern is centered, making sure, at the same time, that the focused electron beam remains on the (sub)grain in question.

“Cavity” formation in superplastically deformed aluminium alloys

1990 ◽  
Vol 48 (4) ◽  
pp. 958-959
Author(s):  
A. Cziráki ◽  
E. Ková-csetényi ◽  
T. Torma ◽  
T. Turmezey
Keyword(s):  
Grain Boundaries ◽  
Aluminium Alloys ◽  
Superplastic Deformation ◽  
Volume Fraction ◽  
Superplastic Forming ◽  
Polished Surface ◽  
Cavity Formation ◽  
Stress Concentrations ◽  
Electron Microscopic ◽  
Commercial Aluminium

It is known that the formation of cavities during superplastic deformation can be correlated with the development of stress concentrations at irregularities along grain boundaries such as particles, ledges and triple points. In commercial aluminium alloys Al-Fe-Si particles or other coarse constituents may play an important role in cavity formation.Cavity formation during superplastic deformation was studied by optical metallography and transmission scanning electron microscopic investigations on Al-Mg-Si and Al-Mg-Mn alloys. The structure of particles was characterized by selected area diffraction and X-ray micro analysis. The volume fraction of “voids” was determined on mechanically polished surface.It was found by electron microscopy that strongly deformed regions are formed during superplastic forming at grain boundaries and around coarse particles.According to electron diffraction measurements these areas consist of small micro crystallized regions. See Fig.l.Comparing the volume fraction and morphology of cavities found by optical microscopy a good correlation was established between that of micro crystalline regions.

Re-examining dominance of categories in impression formation: A test of dual-process models.

2018 ◽  
Vol 115 (1) ◽  
pp. 1-30 ◽  
Author(s):  
Brian M. Monroe ◽  
Bryan L. Koenig ◽  
Kum Seong Wan ◽  
Tei Laine ◽  
Swati Gupta ◽  
...  
Keyword(s):  
Impression Formation ◽  
Process Models ◽  
Dual Process ◽  
Dual Process Models

Habitat use of toothed whales in a marine protected area based on point process models

2019 ◽  
Vol 609 ◽  
pp. 239-256 ◽  
Author(s):  
TL Silva ◽  
G Fay ◽  
TA Mooney ◽  
J Robbins ◽  
MT Weinrich ◽  
...  
Keyword(s):  
Habitat Use ◽  
Point Process ◽  
Protected Area ◽  
Marine Protected Area ◽  
Process Models ◽  
Point Process Models

From Process Models to Concurrent Systems in Alvis Language

Informatica ◽  
2017 ◽  
Vol 28 (3) ◽  
pp. 525-545 ◽  
Author(s):  
Marcin Szpyrka ◽  
Grzegorz J. Nalepa ◽  
Krzysztof Kluza
Keyword(s):  
Concurrent Systems ◽  
Process Models
Sign in / Sign up

Export Citation Format

Share Document