Axial Compressor Stall, Circumferential Groove Casing Treatment, and the Tip-Clearance Momentum Flux

2018 ◽  
Vol 34 (1) ◽  
pp. 146-152
Author(s):  
Mark H. Ross ◽  
Joshua D. Cameron ◽  
Scott C. Morris ◽  
Haixin Chen ◽  
Ke Shi
Keyword(s):  
Momentum Flux ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Casing Treatment ◽  
Circumferential Groove

Experimental and Numerical Investigation of a Circumferential Groove Casing Treatment in a Low Speed Axial Research Compressor at Different Tip Clearances

2017 ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Konrad Vogeler ◽  
Ronald Mailach
Keyword(s):  
Total Pressure ◽  
Solid Wall ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Chord Length ◽  
Single Stage ◽  
Tip Clearance ◽  
Low Speed ◽  
Operating Range ◽  
Circumferential Groove

The demand of increasing pressure ratios for modern high pressure compressors leads to decreasing blade heights in the last stages. As tip clearances cannot be reduced to any amount and minimum values might be necessary for safety reasons, the tip clearance ratios of the last stages can reach values notably higher than current norms. This can be intensified by a compressor running in transient operations where thermal differences can lead to further growing clearances. For decades, the detrimental effects of large clearances on an axial compressor’s operating range and efficiency are known and investigated. The ability of circumferential casing grooves in the rotor casing to improve the compressor’s operating range has also been in the focus of research for many years. Their simplicity and ease of installation are one reason for their continuing popularity nowadays, where advanced methods to increase the operating range of an axial compressor are known. In a previous paper [1], three different circumferential groove casing treatments were investigated in a single stage environment in the Low Speed Axial Research Compressor at TU Dresden. One of these grooves was able to notably improve the operating range and the efficiency of the single stage compressor at very large rotor tip clearances (5% of chord length). In this paper, the results of tests with this particular groove type in a three stage environment in the Low Speed Axial Research Compressor are presented. Two different rotor tip clearance sizes of 1.2% and 5% of tip chord length were investigated. At the small tip clearance, the grooves are almost neutral. Only small reductions in total pressure ratio and efficiency compared to the solid wall can be observed. If the compressor runs with large tip clearances it notably benefits from the casing grooves. Both, total pressure and efficiency can be improved by the grooves in a similar extent as in single stage tests. Five-hole probe measurements and unsteady wall pressure measurements show the influence of the groove on the flow field. With the help of numerical investigations the different behavior of the grooves at the two tip clearance sizes will be discussed.

Experimental Investigation of the Steady and Unsteady Flow Field in a Single Stage Low Pressure Axial Compressor With a Circumferential Groove Casing Treatment

2010 ◽  
Author(s):  
N. Van de Wyer ◽  
B. Farkas ◽  
J. Desset ◽  
J. F. Brouckaert ◽  
J.-F. Thomas ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Unsteady Flow ◽  
Axial Compressor ◽  
Low Pressure ◽  
Fast Response ◽  
Single Stage ◽  
Compressor Stage ◽  
Casing Treatment ◽  
Circumferential Groove

This paper deals with the experimental investigation of the influence of a circumferential groove casing treatment on the performance and stability margin of a single stage low pressure axial compressor. The design of the compressor stage is representative of a booster stage for the new counter-rotating turbofan engine architecture and is characterized by unusually high loading and flow coefficients. The choice of the circumferential groove is described on the basis of a numerical parametric study on the number of grooves, the axial position, the depth and width of the groove. The experiments were performed at a Reynolds number corresponding to cruise conditions in the von Karman Institute closed loop high speed compressor test rig R4. The detailed performance characterization of the compressor stage with casing treatment was mapped at four operating points from choke to stall at design speed. The compressor stall limit was determined at several other off-design speeds. Detailed steady and unsteady measurements were performed to determine the flow field characteristics of the rotor and of the complete stage. Conventional pressure, temperature and directional probes were used along with fast response pressure sensors in the rotor casing and in the groove. Simultaneous traverses with a fast response total pressure probe were used to map the unsteady flow field at the rotor exit allowing an experimental capture of the tip leakage vortex path and extension through the rotor passage. A comparison of the flow features with and without casing treatment was performed and the results are discussed against 3D viscous computational predictions. The casing treatment did not present any improvement of the compressor stall margin but no significant performance degradation was observed either. The CFD predictions showed a good agreement with the measurements and their analysis supported the experimental results.

The Influence of Tip Clearance Momentum Flux on Stall Inception in a High-Speed Axial Compressor

2013 ◽  
Vol 135 (5) ◽  
Author(s):  
Joshua D. Cameron ◽  
Matthew A. Bennington ◽  
Mark H. Ross ◽  
Scott C. Morris ◽  
Juan Du ◽  
...  
Keyword(s):  
Momentum Flux ◽  
High Speed ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Axial Position ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage

Experimental and numerical studies were conducted to investigate tip-leakage flow and its relationship to stall in a transonic axial compressor. The computational fluid dynamics (CFD) results were used to identify the existence of an interface between the approach flow and the tip-leakage flow. The experiments used a surface-streaking visualization method to identify the time-averaged location of this interface as a line of zero axial shear stress at the casing. The axial position of this line, denoted xzs, moved upstream with decreasing flow coefficient in both the experiments and computations. The line was consistently located at the rotor leading edge plane at the stalling flow coefficient, regardless of inflow boundary condition. These results were successfully modeled using a control volume approach that balanced the reverse axial momentum flux of the tip-leakage flow with the momentum flux of the approach fluid. Nonuniform tip clearance measurements demonstrated that movement of the interface upstream of the rotor leading edge plane leads to the generation of short length scale rotating disturbances. Therefore, stall was interpreted as a critical point in the momentum flux balance of the approach flow and the reverse axial momentum flux of the tip-leakage flow.

Effect of Various Trench Designs on Axial Compressor Blade Tip Aerodynamics

2019 ◽  
Author(s):  
Ashwin Ashok ◽  
Patur Ananth Vijay Sidhartha ◽  
Shine Sivadasan
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Suction Side ◽  
Horseshoe Vortex ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Tip Leakage Vortex ◽  
Stall Margin ◽  
Casing Treatment ◽  
Tip Leakage

Abstract Tip clearance of axial compressor blades allows leakage of the flow, generates significant losses and reduces the compressor efficiency. The present paper aims to discuss the axial compressor tip aerodynamics for various configurations of tip gap with trench. The various configurations are obtained by varying the clearance, trench depth, step geometry and casing contouring. In this paper the axial compressor aerodynamics for various configurations of tip gap with trench have been studied. The leakage flow structure, vorticity features and entropy generations are analyzed using RANS based CFD. The linear compressor cascade comprises of NACA 651810 blade with clearance height varied from 0.5% to 2% blade span. Trail of the tip leakage vortex and the horseshoe vortex on the blade suction side are clearly seen for the geometries with and without casing treatments near the stalling point. Since the trench side walls are similar to forward/backing steps, a step vortex is observed near the leading edge as well as trailing edge of the blade and is not seen for the geometry without the casing treatment. Even though the size of the tip leakage vortex seams to be reduces by providing a trench to the casing wall over the blade, the presence of additional vortices like the step vortex leads to comparatively higher flow losses. An increase in overall total pressure loss due to the application of casing treatment is observed. However an increase in stall margin for the geometries with casing is noted.

Time Resolved Experimental Investigations of an Axial Compressor With Casing Treatment

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
R. Emmrich ◽  
H. Hönen ◽  
R. Niehuis
Keyword(s):  
Physical Phenomenon ◽  
Flow Analysis ◽  
Axial Compressor ◽  
Suction Side ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Pressure Probe ◽  
Time Resolved ◽  
Casing Treatment ◽  
Compressor Rotor

A casing treatment with axial and radial skewed slots ending in a plenum chamber has experimentally been investigated at a highly subsonic axial compressor stage. The aim was to investigate the physical phenomenon of this treatment family that is responsible for the stabilization of the blade passage flow and the drop in efficiency mostly observed. The experimentally gained performance results of this configuration showed an extension of the operating range by approximately 50%, while the efficiency for design conditions is reduced by 1.4%. Apart from this, operating points at part load conditions have been observed nearly without any loss in efficiency. The detailed flow analysis is performed by means of results from a 3D pneumatic probe with temperature sensor and a dynamic total pressure probe. The focus of the investigations is on the incidence flow to the compressor rotor, the tip clearance vortex flow in combination with the wall stall separation region and the blade stall due to suction side separation. The casing treatment configuration is investigated with a special interest in detecting those effects which have an impact on the stability and the compressor overall efficiency, including the interaction of the rotor and the stator flow fields.

Experimental and Numerical Investigation of Effect of Center Offset Degree on Compressor Stability With Circumferential Grooved Casing Treatment

2016 ◽  
Author(s):  
HaoGuang Zhang ◽  
Feng Tan ◽  
YanHui Wu ◽  
WuLi Chu ◽  
Wei Wang ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Groove Depth ◽  
Tip Clearance ◽  
Central Difference ◽  
Stall Margin ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
Stall Margin Improvement ◽  
Blade Tip

For compressor blade tip stall, one effective way of extending stable operating range is with the application of circumferential grooved casing treatment and its validity was proved by a lot of experimental and numerical investigations. The emphases of most circumferential grooved investigations are focused on the influence of groove depth and groove number on compressor stability, and there is few investigations dealt with the center offset degree of circumferential grooves casing treatment. Hence, an axial compressor rotor with casing treatment (CT) was investigated with experimental and numerical methods to explore the effect of center offset degree on compressor stability and performance. In the work reported here, The center offset degree is defined as the ratio of the central difference between rotor tip axial chord and CT to the axial chord length of rotor tip. When the center of CT is located within the upstream direction of the center of rotor tip axial chord, the value of center offset degree is positive. The experimental and numerical results show that stall margin improvement gained with CT is reduced as the value of center offset degree varies from 0 to 0.33 or −0.33, and the CT with −0.33 center offset degree achieves the lowest value of stall margin improvement at 53% and 73% design rotational speed. The detailed analysis of the flow-field in compressor tip indicates that there is not positive effect made by grooves on leading edge of rotor blade tip when the value of center offset degree is −0.33. As the mass flow of compressor reduces further, tip clearance leakage flow results in the outlet blockage due to the absence of the positive action of grooves near blade tip tail when the value of center offset degree is 0.33. Blockage does not appear in rotor tip passage owing to utilizing the function of all grooves with CT of 0 center offset degree.

Parametric Study of Tip Clearance – Casing Treatment on Performance and Stability of a Transonic Axial Compressor

2004 ◽  
Author(s):  
Behnam H. Beheshti ◽  
Joao A. Teixeira ◽  
Paul C. Ivey ◽  
Kaveh Ghorbanian ◽  
Bijan Farhanieh
Keyword(s):  
Parametric Study ◽  
Effective Means ◽  
Axial Compressor ◽  
Axial Flow ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Negative Effects ◽  
Compressor Blades ◽  
Casing Treatment ◽  
Tip Leakage

The control of tip leakage flow (TLF) through the clearance gap between the moving and stationary components of rotating machines is still a high-leverage area for improvement of stability and performance of aircraft engines. Losses in the form of flow separation, stall, and reduced rotor work efficiency are results of the tip leakage vortex (TLV) generated by interaction of the main flow and the tip leakage jet induced by the blade pressure difference. The effects are more detrimental in transonic compressors due to the interaction of shock-TLV. It has been previously shown that the use of slots and grooves in the casing over tip of the compressor blades, known as casing treatment, can substantially increase the stable flow range and therefore the safety of the system but generally with some efficiency penalties. This paper presents a numerical parametric study of tip clearance coupled with casing treatment for a transonic axial-flow compressor NASA Rotor 37. Compressor characteristics have been compared to the experimental results for smooth casing with a 0.356 mm tip clearance and show fairly good agreement. Casing treatments were found to be an effective means of reducing the negative effects of tip gap flow and vortex, resulting in improved performance and stability. The present work provides guidelines for improvement of steady-state performance of the transonic axial-flow compressors and improvement of the stable operating range of the system.

A CFD Study of Circumferential Groove Casing Treatments in a Transonic Axial Compressor

2010 ◽  
Author(s):  
Haixin Chen ◽  
Xudong Huang ◽  
Ke Shi ◽  
Song Fu ◽  
Matthew A. Bennington ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Data Sampling ◽  
Stall Margin ◽  
Casing Treatment ◽  
Circumferential Groove ◽  
Compressor Rotor ◽  
Radial Profiles ◽  
Flow Mechanisms ◽  
Transonic Axial Compressor ◽  
And Performance

Numerical investigations were conducted to predict the performance of a transonic axial compressor rotor with circumferential groove casing treatment. The Notre Dame Transonic Axial Compressor (ND-TAC) was simulated by Tsinghua University with an in-house CFD code (NSAWET) for this work. Experimental data from the ND-TAC were used to define the geometry, boundary conditions and data sampling method for the numerical simulation. These efforts, combined with several unique simulation approaches, such as non-matched grid boundary technology to treat the periodic boundaries and interfaces between groove grids and the passage grid, resulted in good agreement between the numerical and experimental results for overall compressor performance and radial profiles of exit total pressure. Efforts were made to study blade level flow mechanisms to determine how the casing treatment impacts the compressor’s stall margin and performance. The flow structures in the passage, the tip gap and the grooves as well as their mutual interactions were plotted and analyzed. The flow and momentum transport across the tip gap in the smooth wall and the casing treatment configurations were quantitatively compared.

Sign in / Sign up

Export Citation Format

Share Document