scholarly journals The stall inceptions in an axial compressor with single circumferential groove casing treatment at different axial locations

2016 ◽  
Vol 59 ◽  
pp. 145-154 ◽  
Author(s):  
Le Liu ◽  
Jichao Li ◽  
Xi Nan ◽  
Feng Lin
Keyword(s):  
Axial Compressor ◽  
Casing Treatment ◽  
Circumferential Groove

Experimental Investigation of the Steady and Unsteady Flow Field in a Single Stage Low Pressure Axial Compressor With a Circumferential Groove Casing Treatment

2010 ◽  
Author(s):  
N. Van de Wyer ◽  
B. Farkas ◽  
J. Desset ◽  
J. F. Brouckaert ◽  
J.-F. Thomas ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Unsteady Flow ◽  
Axial Compressor ◽  
Low Pressure ◽  
Fast Response ◽  
Single Stage ◽  
Compressor Stage ◽  
Casing Treatment ◽  
Circumferential Groove

This paper deals with the experimental investigation of the influence of a circumferential groove casing treatment on the performance and stability margin of a single stage low pressure axial compressor. The design of the compressor stage is representative of a booster stage for the new counter-rotating turbofan engine architecture and is characterized by unusually high loading and flow coefficients. The choice of the circumferential groove is described on the basis of a numerical parametric study on the number of grooves, the axial position, the depth and width of the groove. The experiments were performed at a Reynolds number corresponding to cruise conditions in the von Karman Institute closed loop high speed compressor test rig R4. The detailed performance characterization of the compressor stage with casing treatment was mapped at four operating points from choke to stall at design speed. The compressor stall limit was determined at several other off-design speeds. Detailed steady and unsteady measurements were performed to determine the flow field characteristics of the rotor and of the complete stage. Conventional pressure, temperature and directional probes were used along with fast response pressure sensors in the rotor casing and in the groove. Simultaneous traverses with a fast response total pressure probe were used to map the unsteady flow field at the rotor exit allowing an experimental capture of the tip leakage vortex path and extension through the rotor passage. A comparison of the flow features with and without casing treatment was performed and the results are discussed against 3D viscous computational predictions. The casing treatment did not present any improvement of the compressor stall margin but no significant performance degradation was observed either. The CFD predictions showed a good agreement with the measurements and their analysis supported the experimental results.

A CFD Study of Circumferential Groove Casing Treatments in a Transonic Axial Compressor

2010 ◽  
Author(s):  
Haixin Chen ◽  
Xudong Huang ◽  
Ke Shi ◽  
Song Fu ◽  
Matthew A. Bennington ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Data Sampling ◽  
Stall Margin ◽  
Casing Treatment ◽  
Circumferential Groove ◽  
Compressor Rotor ◽  
Radial Profiles ◽  
Flow Mechanisms ◽  
Transonic Axial Compressor ◽  
And Performance

Numerical investigations were conducted to predict the performance of a transonic axial compressor rotor with circumferential groove casing treatment. The Notre Dame Transonic Axial Compressor (ND-TAC) was simulated by Tsinghua University with an in-house CFD code (NSAWET) for this work. Experimental data from the ND-TAC were used to define the geometry, boundary conditions and data sampling method for the numerical simulation. These efforts, combined with several unique simulation approaches, such as non-matched grid boundary technology to treat the periodic boundaries and interfaces between groove grids and the passage grid, resulted in good agreement between the numerical and experimental results for overall compressor performance and radial profiles of exit total pressure. Efforts were made to study blade level flow mechanisms to determine how the casing treatment impacts the compressor’s stall margin and performance. The flow structures in the passage, the tip gap and the grooves as well as their mutual interactions were plotted and analyzed. The flow and momentum transport across the tip gap in the smooth wall and the casing treatment configurations were quantitatively compared.

scholarly journals A Study of Casing Treatment Stall Margin Improvement Phenomena

1975 ◽  
Author(s):  
D. C. Prince ◽  
D. C. Wisler ◽  
D. E. Hilvers
Keyword(s):  
Rotor Blade ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Blade Angle ◽  
Normal Surface ◽  
Peak Efficiency ◽  
Stall Margin ◽  
Casing Treatment ◽  
Circumferential Groove ◽  
Wall Boundary Layer

The results of a program of experimental and analytical research in casing treatments over axial compressor rotor blade tips are presented. Circumferential groove, axial-skewed slot, and blade angle slot treatments were tested at low speeds. With the circumferential groove treatment the stalling flow was reduced 5.8 percent at negligible efficiency sacrifice. The axial-skewed slot treatment improved the stalling flow by 15.3 percent; 1.8 points in peak efficiency were sacrificed. The blade angle slot treatment improved the stalling flow by 15.0 percent; 1.4 points in peak efficiency were sacrificed. These values are consistent with previous experience at transonic speeds. The favorable stalling flow situations correlated well with observations of higher-than-normal surface pressures on the rotor blade pressure surfaces in the tip region, and with increased maximum diffusions on the suction surfaces. Annulus wall pressure gradients, especially in the 50 to 75 percent chord region, are also increased and blade surface pressure loadings are shifted toward the trailing edge for treated configurations. Rotor blade wakes may be somewhat thinner in the presence of good treatments, particularly under operating conditions close to the baseline stall. Annulus wall boundary layer profiles are only slightly influenced by casing treatment.

scholarly journals Toward Optimum Configuration of Circumferential Groove Casing Treatment in Transonic Compressor Rotors

2011 ◽  
Author(s):  
Chunill Hah
Keyword(s):  
Optimum Design ◽  
Flow Measurement ◽  
High Speed ◽  
Axial Compressor ◽  
Significant Advance ◽  
Future Research ◽  
Flow Physics ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Circumferential Groove

The current paper first reviews experimental and numerical investigations to understand flow physics and to develop optimum configurations of circumferential grooves in compressor rotors. Circumferential grooves are used mainly to increase stall margin in axial compressors with small decrease in aerodynamic efficiency. Although circumferential groove casing treatment has been used widely, flow mechanisms of the circumferential grooves at near stall conditions are not well understood yet. Detailed time-dependent flow measurement inside tip gap in a high speed compressor is still a big challenge even though significant advance has been made in non-intrusive flow measurement technique. Therefore numerical approaches have been used to study relevant flow physics. However, optimum design of circumferential grooves to a given compressor with the computational tools is not practical yet. In the present paper, various investigations to study flow physics of circumferential groove casing treatment in axial compressor are reviewed first. Possible missing flow physics are identified and future research efforts for the optimum design are discussed.

Experimental and Numerical Investigation of a Circumferential Groove Casing Treatment in a Low-Speed Axial Research Compressor at Different Tip Clearances

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Konrad Vogeler ◽  
Ronald Mailach
Keyword(s):  
Total Pressure ◽  
Solid Wall ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Chord Length ◽  
Single Stage ◽  
Low Speed ◽  
Casing Treatment ◽  
Operating Range ◽  
Circumferential Groove

The demand of increasing pressure ratios for modern high pressure compressors leads to decreasing blade heights in the last stages. As tip clearances (TC) cannot be reduced to any amount and minimum values might be necessary for safety reasons, the TC ratios of the last stages can reach values notably higher than current norms. This can be intensified by a compressor running in transient operations where thermal differences can lead to further growing clearances. For decades, the detrimental effects of large clearances on an axial compressor's operating range and efficiency are known and investigated. The ability of circumferential casing grooves in the rotor casing to improve the compressor's operating range has also been in the focus of research for many years. Their simplicity and ease of installation are one reason for their continuing popularity nowadays, where advanced methods to increase the operating range of an axial compressor are known. In the authors' previous paper, three different circumferential groove casing treatments were investigated in a single-stage environment in the low-speed axial research compressor at TU Dresden. One of these grooves was able to notably improve the operating range and the efficiency of the single stage compressor at very large rotor TC (5% of chord length). In this paper, the results of tests with this particular groove type in a three stage environment in the low-speed axial research compressor are presented. Two different rotor TC sizes of 1.2% and 5% of tip chord length were investigated. At the small TC, the grooves are almost neutral. Only small reductions in total pressure ratio and efficiency compared to the solid wall can be observed. If the compressor runs with large TC, it notably benefits from the casing grooves. Both, total pressure and efficiency can be improved by the grooves in a similar extent as in single stage tests. Five-hole probe measurements and unsteady wall pressure measurements show the influence of the groove on the flow field. With the help of numerical investigations, the different behavior of the grooves at the two TC sizes will be discussed.

Axial Compressor Stall, Circumferential Groove Casing Treatment, and the Tip-Clearance Momentum Flux

2018 ◽  
Vol 34 (1) ◽  
pp. 146-152
Author(s):  
Mark H. Ross ◽  
Joshua D. Cameron ◽  
Scott C. Morris ◽  
Haixin Chen ◽  
Ke Shi
Keyword(s):  
Momentum Flux ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Casing Treatment ◽  
Circumferential Groove

A Computational Fluid Dynamics Study of Circumferential Groove Casing Treatment in a Transonic Axial Compressor

2013 ◽  
Vol 136 (3) ◽  
Author(s):  
Haixin Chen ◽  
Xudong Huang ◽  
Ke Shi ◽  
Song Fu ◽  
Mark Ross ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Axial Compressor ◽  
Data Sampling ◽  
Stall Margin ◽  
Casing Treatment ◽  
Circumferential Groove ◽  
Compressor Rotor ◽  
Radial Profiles ◽  
Transonic Axial Compressor

Numerical investigations were conducted to predict the performance of a transonic axial compressor rotor with circumferential groove casing treatment. The Notre Dame Transonic Axial Compressor (ND-TAC) was simulated at Tsinghua University with an in-house computational fluid dynamics (CFD) code (NSAWET) for this work. Experimental data from the ND-TAC were used to define the geometry, boundary conditions, and data sampling method for the numerical simulation. These efforts, combined with several unique simulation approaches, such as nonmatched grid boundary technology to treat the periodic boundaries and interfaces between groove grids and the passage grid, resulted in good agreement between the numerical and experimental results for overall compressor performance and radial profiles of exit total pressure. Efforts were made to study blade level flow mechanisms to determine how the casing treatment impacts the compressor's stall margin and performance. The flow structures in the passage, the tip gap, and the grooves as well as their mutual interactions were plotted and analyzed. The flow and momentum transport across the tip gap in the smooth wall and the casing treatment configurations were quantitatively compared.

Recirculation-groove coupled casing treatment for a transonic axial compressor

2021 ◽  
Vol 111 ◽  
pp. 106556
Author(s):  
Tien-Dung Vuong ◽  
Kwang-Yong Kim ◽  
Cong-Truong Dinh
Keyword(s):  
Axial Compressor ◽  
Casing Treatment ◽  
Transonic Axial Compressor

scholarly journals Effects of Endwall Suction and Blowing on Compressor Stability Enhancement

1989 ◽  
Author(s):  
N. K. W. Lee ◽  
E. M. Greitzer
Keyword(s):  
Flow Injection ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Primary Objective ◽  
Stall Margin ◽  
Casing Treatment ◽  
Blade Row ◽  
Stall Margin Improvement ◽  
Stability Enhancement ◽  
Suction And Blowing

An experimental investigation was carried out to examine the effects on stall margin of flow injection into, and flow removal out of, the endwall region of an axial compressor blade row. A primary objective of the investigation was clarification of the mechanism by which casing treatment (which involves both removal and injection) suppresses stall in turbomachines. To simulate the relative motion between blade and treatment, the injection and removal took place through a slotted hub rotating beneath a cantilevered stator row. Overall performance data and detailed (time-averaged) flowfield measurements were obtained. Flow injection and removal both increased the stalling pressure rise, but neither was as effective as the wall treatment. Removal of high blockage flow is thus not the sole reason for the observed stall margin improvement in casing or hub treatment, as injection can also contribute significantly to stall suppression. The results also indicate that the increase in stall pressure rise with injection is linked to the streamwise momentum of the injected flow, and it is suggested that this should be the focus of further studies.

Sign in / Sign up

Export Citation Format

Share Document