Time Resolved Experimental Investigations of an Axial Compressor With Casing Treatment

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
R. Emmrich ◽  
H. Hönen ◽  
R. Niehuis
Keyword(s):  
Physical Phenomenon ◽  
Flow Analysis ◽  
Axial Compressor ◽  
Suction Side ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Pressure Probe ◽  
Time Resolved ◽  
Casing Treatment ◽  
Compressor Rotor

A casing treatment with axial and radial skewed slots ending in a plenum chamber has experimentally been investigated at a highly subsonic axial compressor stage. The aim was to investigate the physical phenomenon of this treatment family that is responsible for the stabilization of the blade passage flow and the drop in efficiency mostly observed. The experimentally gained performance results of this configuration showed an extension of the operating range by approximately 50%, while the efficiency for design conditions is reduced by 1.4%. Apart from this, operating points at part load conditions have been observed nearly without any loss in efficiency. The detailed flow analysis is performed by means of results from a 3D pneumatic probe with temperature sensor and a dynamic total pressure probe. The focus of the investigations is on the incidence flow to the compressor rotor, the tip clearance vortex flow in combination with the wall stall separation region and the blade stall due to suction side separation. The casing treatment configuration is investigated with a special interest in detecting those effects which have an impact on the stability and the compressor overall efficiency, including the interaction of the rotor and the stator flow fields.

Time Resolved Investigations of an Axial Compressor With Casing Treatment: Part 1 — Experiment

2007 ◽  
Author(s):  
R. Emmrich ◽  
H. Ho¨nen ◽  
R. Niehuis
Keyword(s):  
Physical Phenomenon ◽  
Flow Analysis ◽  
Axial Compressor ◽  
Suction Side ◽  
Tip Clearance ◽  
Pressure Probe ◽  
Time Resolved ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
The Stability

A casing treatment with axial and radial skewed slots ending in a plenum chamber has experimentally been investigated at a highly subsonic axial compressor stage. The aim was to investigate the physical phenomenon of this treatment family that is responsible for the stabilization of the blade passage flow and the drop in efficiency mostly observed. The experimentally gained performance results of this configuration showed an extension of the operating range by approximately 50%, while the efficiency for design conditions is reduced by 1.4%. Apart from this, operating points at part load conditions have been observed nearly without any loss in efficiency. The detailed flow analysis is performed by means of results from a 3D pneumatic probe with temperature sensor and a dynamic total pressure probe. The focus of the investigations is on the incidence flow to the compressor rotor, the tip clearance vortex flow in combination with the wall stall separation region and the blade stall due to suction side separation. The casing treatment configuration is investigated with a special interest in detecting those effects which have an impact on the stability and the compressor overall efficiency, including the interaction of the rotor and the stator flow fields.

Effect of Various Trench Designs on Axial Compressor Blade Tip Aerodynamics

2019 ◽  
Author(s):  
Ashwin Ashok ◽  
Patur Ananth Vijay Sidhartha ◽  
Shine Sivadasan
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Suction Side ◽  
Horseshoe Vortex ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Tip Leakage Vortex ◽  
Stall Margin ◽  
Casing Treatment ◽  
Tip Leakage

Abstract Tip clearance of axial compressor blades allows leakage of the flow, generates significant losses and reduces the compressor efficiency. The present paper aims to discuss the axial compressor tip aerodynamics for various configurations of tip gap with trench. The various configurations are obtained by varying the clearance, trench depth, step geometry and casing contouring. In this paper the axial compressor aerodynamics for various configurations of tip gap with trench have been studied. The leakage flow structure, vorticity features and entropy generations are analyzed using RANS based CFD. The linear compressor cascade comprises of NACA 651810 blade with clearance height varied from 0.5% to 2% blade span. Trail of the tip leakage vortex and the horseshoe vortex on the blade suction side are clearly seen for the geometries with and without casing treatments near the stalling point. Since the trench side walls are similar to forward/backing steps, a step vortex is observed near the leading edge as well as trailing edge of the blade and is not seen for the geometry without the casing treatment. Even though the size of the tip leakage vortex seams to be reduces by providing a trench to the casing wall over the blade, the presence of additional vortices like the step vortex leads to comparatively higher flow losses. An increase in overall total pressure loss due to the application of casing treatment is observed. However an increase in stall margin for the geometries with casing is noted.

Experimental and Numerical Investigation of Effect of Center Offset Degree on Compressor Stability With Circumferential Grooved Casing Treatment

2016 ◽  
Author(s):  
HaoGuang Zhang ◽  
Feng Tan ◽  
YanHui Wu ◽  
WuLi Chu ◽  
Wei Wang ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Groove Depth ◽  
Tip Clearance ◽  
Central Difference ◽  
Stall Margin ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
Stall Margin Improvement ◽  
Blade Tip

For compressor blade tip stall, one effective way of extending stable operating range is with the application of circumferential grooved casing treatment and its validity was proved by a lot of experimental and numerical investigations. The emphases of most circumferential grooved investigations are focused on the influence of groove depth and groove number on compressor stability, and there is few investigations dealt with the center offset degree of circumferential grooves casing treatment. Hence, an axial compressor rotor with casing treatment (CT) was investigated with experimental and numerical methods to explore the effect of center offset degree on compressor stability and performance. In the work reported here, The center offset degree is defined as the ratio of the central difference between rotor tip axial chord and CT to the axial chord length of rotor tip. When the center of CT is located within the upstream direction of the center of rotor tip axial chord, the value of center offset degree is positive. The experimental and numerical results show that stall margin improvement gained with CT is reduced as the value of center offset degree varies from 0 to 0.33 or −0.33, and the CT with −0.33 center offset degree achieves the lowest value of stall margin improvement at 53% and 73% design rotational speed. The detailed analysis of the flow-field in compressor tip indicates that there is not positive effect made by grooves on leading edge of rotor blade tip when the value of center offset degree is −0.33. As the mass flow of compressor reduces further, tip clearance leakage flow results in the outlet blockage due to the absence of the positive action of grooves near blade tip tail when the value of center offset degree is 0.33. Blockage does not appear in rotor tip passage owing to utilizing the function of all grooves with CT of 0 center offset degree.

Numerical Study on the Effects of Casing Treatment on Unsteadiness of Tip Leakage Flow in an Axial Compressor

2012 ◽  
Author(s):  
Yoojun Hwang ◽  
Shin-Hyoung Kang
Keyword(s):  
Numerical Study ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Casing Treatment ◽  
Tip Leakage ◽  
Operating Range ◽  
Compressor Rotor ◽  
Flow Through

A low speed axial compressor with casing treatment of axial slots was numerically investigated. Time-accurate numerical calculations were performed to simulate unsteady flow in the rotor tip region and the effects of casing treatment on the flow. Since the compressor rotor had a large tip clearance, it was found that the tip leakage flow had an inherent unsteady feature that was not associated with rotor rotation. The unsteadiness of the tip leakage flow was induced by changes in the blade loading due to the pressure distribution formed by the tip leakage flow. This characteristic is called rotating instability or self-induced unsteadiness. The frequency of the flow oscillation was found to decrease as the flow rate was reduced. On the other hand, as expected, the operating range was improved by casing treatment, as shown by calculations in good agreement with the experimentally measured data. The unsteadiness of the tip leakage flow was alleviated by the casing treatment. The interaction between the flow in the tip region and the re-circulated flow through the axial slots was observed in detail. The removal and injection of flow through the axial slots were responsible not only for the extension of the operating range but also for the alleviation of the unsteadiness. Analyses of instantaneous flow fields explained the mechanism of the interaction between the casing treatment and the unsteady oscillation of the tip leakage flow. Furthermore, the effects of changes in the amount of re-circulation and the location of the removal and injection flow on the unsteadiness of the tip leakage flow were examined.

Study of Sloped Trench Casing Treatment on Performance and Stability of a Transonic Axial Compressor

2007 ◽  
Author(s):  
Hui Zhang ◽  
Hongwei Ma
Keyword(s):  
Performance Improvement ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Smooth Transition ◽  
Nasa Lewis Research ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
Transonic Axial Compressor ◽  
Simulation Results ◽  
A Performance

This paper presents a numerical investigation of effects of sloped trench casing treatment over the rotor tip on the aerodynamic performance and stability of a transonic axial compressor rotor (NASA Rotor 37). The axially cutting tip of blade is the marked characteristic of the casing treatment which is differ with casing treatments without adjustment of the blade tip. The numerical method has been verified by experimental results in the case of the smooth casing with the tip clearance of 0.356 mm at the design wheel speed (17188.7 rpm). The simulation results are well consistent with the measurement results. The experiment results of NASA Rotor 37 cite from NASA Lewis Research Center. The simulation results show a performance improvement of the compressor on the sloped trench casing. The flow fields of the smooth and sloped trench casings were compared, and results show the sloped trench geometry provides a barrier to minimize the forward flow from the tip clearance vortex. In addition, the sloped trench allows the forward facing step at the aft end to be replaced by an aerodynamically smooth transition to guide the flow from the recess into the mainstream. These results show a performance improvement of the compressor.

Performance Desensitization for a High-Speed Axial Compressor

2018 ◽  
Author(s):  
Yassine Souleimani ◽  
Huu Duc Vo ◽  
Hong Yu
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Lower Sensitivity ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Casing Treatment ◽  
Compressor Rotor

The increase in compressor tip clearance over the lifespan of an aero-engine leads to a long-term degradation in its fuel consumption and operating envelope. A highly promising recent numerical study on a theoretical high-speed axial compressor rotor proposed a novel casing treatment to decrease performance and stall margin sensitivity to tip clearance increase. This paper aims to apply and analyze, through CFD simulations, this casing treatment concept to a representative production axial compressor rotor with inherently lower sensitivity to tip clearance increase and complement the explanation on the mechanism behind the reduction in sensitivity. Simulations of the baseline rotor showed that the lower span region contribute as much to the pressure ratio sensitivity as the tip region which is dominated by tip leakage flow. In contrast, the efficiency sensitivity is mainly driven by losses occurring in the tip region. The novel casing treatment was successfully applied to the baseline rotor through a design refinement. Although the casing treatment causes some penalty in nominal performance, it completely reversed the pressure ratio sensitivity (i.e. pressure ratio increases with tip clearance) and reduced the efficiency sensitivity. The reversed pressure ratio sensitivity is explained by a rotation in the core flow in the lower span region indirectly induced by the flow injection from the casing treatment. The lower efficiency sensitivity comes from a reduction in the amount of fluid that crosses the tip clearance of two adjacent blades, known as double leakage. The casing treatment’s beneficial effect on stall margin sensitivity is less obvious because of the stall inception type of the baseline rotor and its change in the presence of the casing treatment.

Part-Circumference Casing Treatment and the Effect on Compressor Stall

1989 ◽  
Author(s):  
N. A. Cumpsty
Keyword(s):  
Axial Compressor ◽  
Tip Clearance ◽  
Start Time ◽  
Stall Inception ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Stall Margin Improvement

Results are presented and discussed from an axial compressor rotor operated with an axial skewed slot casing treatment over part of the circumference. The compressor was one for which stall was initiated in the tip region and for this type there is some potential for stall margin improvement with lower loss using this. The main significance of the experiments is, however, the possibility of looking at aspects of stall inception. Normally stall inception is a brief transient with an unknown start time and is difficult to study but with the partial casing treatment it was possible to make the untreated section operate continuously in such a way that it underwent the processes normally leading to stall. For a tip stalling rotor the experiments identify the annulus boundary layer as the crucial region of the flow and spillage of the tip-clearance flow forward of the blades as a process leading to the rapid build up of blockage prior to instability and stall.

Study of Effects of Rotor Tip Tailoring in Axial Flow Compressors

2015 ◽  
Author(s):  
Chaitanya V. Halbe ◽  
Yashovardhan S. Chati ◽  
Jubin Tom George ◽  
A. M. Pradeep ◽  
Bhaskar Roy ◽  
...  
Keyword(s):  
Flow Analysis ◽  
Axial Compressor ◽  
Axial Flow ◽  
Leading Edge ◽  
Tip Clearance ◽  
Baseline Design ◽  
Low Speed ◽  
Compressor Rotor ◽  
Multistage Compressor ◽  
Novel Design

The performance of an axial compressor rotor is known to be affected by the variations in tip clearance during its operation. This effect is pronounced for the rear stages of a multistage compressor. This paper describes a novel design that is shown to aerodynamically desensitize the rotor tip to the tip clearance variations. The effect of tip clearance variations on the performance of a baseline low speed, high hub-to-tip ratio axial compressor rotor is studied using CFD. Based on the understanding developed from this flow analysis, the baseline rotor is redesigned by tailoring the tip and redistributing the blade loading over the span. The tip tailoring results in a blade with split dihedral, i.e. of applied dihedral variable from the leading edge to the trailing edge. CFD analysis of the tip tailored configuration shows lower pressure drop with increasing tip clearance as compared to the baseline design. The simulation results are validated through testing in a low speed axial compressor rig, thereby giving experimental support to the desensitization of the rotor to the studied tip clearance variations by tip tailoring.

Surface Roughness Impact on Secondary Flow and Losses in a Turbine Exhaust Casing

2018 ◽  
Author(s):  
Isak Jonsson ◽  
Valery Chernoray ◽  
Borja Rojo
Keyword(s):  
Surface Roughness ◽  
Secondary Flow ◽  
Suction Side ◽  
Pressure Probe ◽  
Time Resolved ◽  
Pressure Distributions ◽  
Turbulence Decay ◽  
Inlet Swirl ◽  
High Level ◽  
The Impact

This paper experimentally addresses the impact of surface roughness on losses and secondary flow in a Turbine Rear Structure (TRS). Experiments were performed in the Chalmers LPT-OGV facility, at an engine representative Reynolds number with a realistic shrouded rotating low-pressure turbine (LPT). Outlet Guide Vanes (OGV) were manufactured to achieve three different surface roughnesses tested at two Reynolds numbers, Re = 235000 and Re = 465000. The experiments were performed at on-design inlet swirl conditions. The inlet and outlet flow of the TRS were measured in 2D planes with a 5-hole probe and 7-hole probe accordingly. The static pressure distributions on the OGVs were measured and boundary layer studies were performed at the OGV midspan on the suction side with a time-resolved total pressure probe. Turbulence decay was measured within the TRS with a single hot-wire. The results showed a surprisingly significant increase in the losses for the high level of surface roughness (25–30 Ra) of the OGVs and Re = 465000. The increased losses were primary revealed as a result of the flow separation on the OGV suction side near the hub. The loss increase was seen but was less substantial for the intermediate roughness case (4–8 Ra). Experimental results presented in this work provide support for the further development of more advanced TRS and data for the validation of new CFD prediction methods for TRS.

Visualization and Time-Resolved Particle Image Velocimetry Measurements of the Flow in the Tip Region of a Subsonic Compressor Rotor

2014 ◽  
Vol 137 (4) ◽  
Author(s):  
David Tan ◽  
Yuanchao Li ◽  
Ian Wilkes ◽  
Rinaldo L. Miorini ◽  
Joseph Katz
Keyword(s):  
Flow Rate ◽  
High Speed ◽  
Axial Compressor ◽  
Time Resolved ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Direct Measurements ◽  
Image Velocimetry ◽  
The One ◽  
And Behavior

A new optically index matched facility has been constructed to investigate tip flows in compressor-like settings. The blades of the one and a half stage compressor have the same geometry, but lower aspect ratio as the inlet guide vanes (IGVs) and the first stage of the low-speed axial compressor (LSAC) facility at NASA Glenn. With transparent blades and casings, the new setup enables unobstructed velocity measurements at any point within the tip region and is designed to facilitate direct measurements of effects of casing treatments on the flow structure. We start with a smooth endwall casing. High speed movies of cavitation and time-resolved PIV measurements have been used to characterize the location, trajectory, and behavior of the tip leakage vortex (TLV) for two flow rates, the lower one representing prestall conditions. Results of both methods show consistent trends. As the flow rate is reduced, TLV rollup occurs further upstream, and its initial orientation becomes more circumferential. At prestall conditions, the TLV is initially aligned slightly upstream of the rotor passage, and subsequently forced downstream. Within the passage, the TLV breaks up into a large number of vortex fragments, which occupy a broad area. Consequently, the cavitation in the TLV core disappears. With decreasing flow rate, this phenomenon becomes more abrupt, occurs further upstream, and the fragments occupy a larger area.

Sign in / Sign up

Export Citation Format

Share Document