scholarly journals Optimization of esterification activity of lipase from Candida rugosa immobilized using microwave irradiation

2012 ◽  
Vol 66 (1) ◽  
pp. 9-19
Author(s):  
Mladen Mihailovic ◽  
Zorica Knezevic-Jugovic ◽  
Dusan Mijin ◽  
Dejan Bezbradica
Keyword(s):  
Microwave Irradiation ◽  
Lipase Activity ◽  
Candida Rugosa ◽  
Water Concentration ◽  
Pharmaceutical Products ◽  
Enzyme Concentration ◽  
Molar Ratio ◽  
Immobilization Time ◽  
Substrate Conversion ◽  
Substrate Molar Ratio

Lipases are very efficient biocatalysts with wide application in synthesis of important ingredients of food, cosmetics and pharmaceutical products, due to their capacity to catalyze both, ester synthesis and ester hydrolysis. The preparation of stable and active immobilized derivatives of lipases is necessity for their application in industrial enzymatic processes. In this work, the optimization of lipase from C. rugosa immobilization by microwave irradiation was performed, since it was previously reported that immobilization process can be drastically accelerated by means of microwave irradiation, even resulting with slight increase of lipase activity. Eupergit?, commercial support with active epoxy groups, was used as immobilization support. In first stage of our study, the immobilization time and ionic strength of immobilization buffer were optimized. It was found out that the highest immobilized activity can be achieved at high ionic strengths (1 M buffer) after 3 min, while further increase of immobilization time led to decrease of lipase activity. Then, the immobilized derivative obtained at optimum conditions was applied in synthesis of amyl isobutyrate in organic solvent. Key reaction factors (temperature, water concentration, immobilized lipase concentration, and substrate molar ratio) were optimized using response surface methodology. The substrate conversion higher above 85% was achieved in our study. The statistical analysis revealed that each of analyzed factors had significant effect on yield of ester, with initial enzyme concentration and substrate molar ratio being the most prominent factors. The second-order regression model that describes the effect of all four factors on substrate conversion was established. The optimum values of factors were: temperature 50?C, initial immobilized enzyme concentration 220 mg ml-1, added water concentration 0.1% (v/v), and molar ratio acid/alcohol 2.5.

scholarly journals Immobilization of lipase on sepabeads and its application in pentyl octanoate synthesis in a low aqueous system

2008 ◽  
pp. 139-152 ◽  
Author(s):  
Zorica Knezevic-Jugovic ◽  
SvetlanaV. Saponjic ◽  
Dejan Bezbradica ◽  
Dusan Mijin
Keyword(s):  
Molecular Sieves ◽  
Immobilized Lipase ◽  
Candida Rugosa ◽  
Aqueous System ◽  
Molar Ratio ◽  
Process Conditions ◽  
Initial Water Content ◽  
Initial Water ◽  
Initial Substrate ◽  
Substrate Molar Ratio

The object of the study was to investigate the process conditions relevant for the pentyl octanoate production with the lipase from Candida rugosa immobilized on Sepabeads EC-EP carrier. This is an epoxide-containing commercial polymethacrylic carrier with suitable characteristics for enzyme immobilization. The immobilized lipase suitable for pentyl octanoate synthesis has been prepared by a direct lipase binding to polymers via their epoxide groups. The enzymatic activity was determined by both hydrolysis of olive oil in an aqueous system and esterification of n-pentanol with octanoic acid in a low aqueous system. The influence of several important reaction parameters such as temperature, initial water content, initial substrate molar ratio, enzyme loading and time of adding of molecular sieves in the system is carefully analyzed by means of an experimental design. Production of the ester was optimized and an ester production response equation was obtained, making it possible to predict ester yields from known values of the five main factors. Almost complete conversion (>99%) of the substrate to ester could be realized, using lipase loading as low as 37 mg/g dry support and in a relatively short time (24 h) at 45?C, when high initial substrate molar ratio of 2.2 is used.

scholarly journals Rapid and Efficient Synthesis ofω-Alkylenediphosphoric Acids from Phosphorus Oxychloride

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Dalila Meziane ◽  
Abdelhamid Elias ◽  
Erwann Guénin
Keyword(s):  
Microwave Irradiation ◽  
Reaction Temperature ◽  
Phosphorus Oxychloride ◽  
Molar Ratio ◽  
Efficient Synthesis ◽  
Selective Method

The aim of this investigation was to develop an efficient, rapid, and selective method for the synthesis ofω-alkylenediphosphoric acids (HO)2(O)P-O-CH2n-O-P(O)(OH)2from reaction of several diols with phosphorus oxychloride. The reaction was investigated using three methodologies: (i) presence of a base, (ii) classical heating, and (iii) use of microwave irradiation. Influence of reaction temperature and molar ratio of reagents, as well as the nature of the solvent, was studied using these three different methods.

scholarly journals Continuous Production of Lipase-Catalyzed Biodiesel in a Packed-Bed Reactor: Optimization and Enzyme Reuse Study

2011 ◽  
Vol 2011 ◽  
pp. 1-6 ◽  
Author(s):  
Hsiao-Ching Chen ◽  
Hen-Yi Ju ◽  
Tsung-Ta Wu ◽  
Yung-Chuan Liu ◽  
Chih-Chen Lee ◽  
...  
Keyword(s):  
Flow Rate ◽  
Immobilized Lipase ◽  
Continuous Production ◽  
Packed Bed ◽  
Packed Bed Reactor ◽  
Molar Ratio ◽  
System Response ◽  
Biodiesel Synthesis ◽  
Substrate Molar Ratio ◽  
Molar Conversion

An optimal continuous production of biodiesel by methanolysis of soybean oil in a packed-bed reactor was developed using immobilized lipase (Novozym 435) as a catalyst in atert-butanol solvent system. Response surface methodology (RSM) and Box-Behnken design were employed to evaluate the effects of reaction temperature, flow rate, and substrate molar ratio on the molar conversion of biodiesel. The results showed that flow rate and temperature have significant effects on the percentage of molar conversion. On the basis of ridge max analysis, the optimum conditions were as follows: flow rate 0.1 mL/min, temperature52.1∘C, and substrate molar ratio 1 : 4. The predicted and experimental values of molar conversion were83.31±2.07% and82.81±.98%, respectively. Furthermore, the continuous process over 30 days showed no appreciable decrease in the molar conversion. The paper demonstrates the applicability of using immobilized lipase and a packed-bed reactor for continuous biodiesel synthesis.

Optimization of biodiesel synthesis under simultaneous ultrasound-microwave irradiation using response surface methodology (RSM)

2015 ◽  
Vol 4 (4) ◽  
Author(s):  
Seyed Mohammad Safieddin Ardebili ◽  
Teymor Tavakoli Hashjin ◽  
Barat Ghobadian ◽  
Gholamhasan Najafi ◽  
Stefano Mantegna ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Microwave Irradiation ◽  
Response Surface ◽  
Palm Oil ◽  
Catalyst Concentration ◽  
Irradiation Time ◽  
Operating Conditions ◽  
Molar Ratio ◽  
Reaction Conditions ◽  
Biodiesel Synthesis

AbstractThis work investigates the effect of simultaneous ultrasound-microwave irradiation on palm oil transesterification and uncovers optimal operating conditions. Response surface methodology (RSM) has been used to analyze the influence of reaction conditions, including methanol/palm oil molar ratio, catalyst concentration, reaction temperature and irradiation time on biodiesel yield. RSM analyses indicate 136 s and 129 s as the optimal sonication and microwave irradiation times, respectively. Optimized parameters for full conversion (97.53%) are 1.09% catalyst concentration and a 7:3.1 methanol/oil molar ratio at 58.4°C. Simultaneous ultrasound-microwave irradiation dramatically accelerates the palm oil transesterification reaction. Pure biodiesel was obtained after only 2.2 min while the conventional method requires about 1 h.

Lipase-Catalyzed Acyl-L-Carnitines Synthesis in [Bmim]PF6 Ionic Liquid

2009 ◽  
Vol 5 (1) ◽  
Author(s):  
Jin-qiang Tian ◽  
Qiang Wang ◽  
Zhong-yuan Zhang
Keyword(s):  
Ionic Liquid ◽  
Lipase Activity ◽  
Molecular Sieves ◽  
Reaction Medium ◽  
Molar Ratio ◽  
Reaction Conditions ◽  
Optimal Reaction ◽  
Better Than

In order to significantly improve the biosynthesis of acyl-L-carnitines catalyzed by lipase, there must be an efficient and suitable reaction medium that is not only polar but also hydrophobic. [Bmim]PF6, which satisfies the above two requirements, was applied as the medium. The optimal reaction conditions were: for isovaleryl-L-carnitine, 0.22aW, 200mg molecular sieves, 60ºC, 4:1 of molar ratio (fatty acid:L-carnitine), 150rpm and 60h; for octanoyl-L-carnitine and palmitoyl-L-carnitine, 0.22aW, 250 mg molecular sieves, 5:1 of molar ratio (fatty acid:L-carnitine), 200rpm, 48h, 60ºC (octanoyl-L-carnitine) and 65ºC (palmitoyl-L-carnitine). Their overall yields could reach 59.14%, 90.79% and 98.03%, respectively. The yields of isovaleryl-L-carnitine, octanoyl-L-carnitine and palmitoyl-L-carnitine in [Bmim]PF6 were 16.21%, 73.67% and 44.22 % more than those in acetonitrile, respectively. [Bmim]PF6 as the medium was better than acetonitrile. It could not only enhance the yields of acyl-L-carnitines, but also protect the lipase activity.

Microwave Assisted Synthesis of Schiff Bases: A Green Approach

2012 ◽  
Vol 10 (1) ◽  
Author(s):  
Mousumi Chakraborty ◽  
Sanjay Baweja ◽  
Sunita Bhagat ◽  
TejpalSingh Chundawat
Keyword(s):  
Microwave Irradiation ◽  
Microwave Power ◽  
Mass Spectra ◽  
Molar Ratio ◽  
Microwave Assisted Synthesis ◽  
Schiff’S Bases ◽  
Microwave Assisted ◽  
Green Approach ◽  
Schiff's Bases ◽  
Effects Of Temperature

Abstract In the present study Schiff’s bases are synthesized by the conventional as well as by microwave irradiation. Excellent yield within short reaction time is obtained using microwave irradiation along with other advantages like mild reaction condition, non-hazardous and safer environmental conditions. The effects of temperature, reactant molar ratio, and microwave power variation on yield are observed. Mathematical model has been developed using matlab software to obtain the yield as a function of microwave power. Kinetic study of the reaction has also been attempted. Schiff’s bases structures are confirmed by IR, 1HNMR, Mass Spectra and elemental analysis.

Heterogeneous Microwave Irradiation Biodiesel Processing of Jatropha Oil

2014 ◽  
Vol 554 ◽  
pp. 500-504 ◽  
Author(s):  
Farid Nasir Ani ◽  
Ahmed Bakheit Elhameed
Keyword(s):  
Reaction Time ◽  
Methyl Ester ◽  
Microwave Irradiation ◽  
Calcium Oxide ◽  
Production Cost ◽  
Catalyst Concentration ◽  
Molar Ratio ◽  
Biodiesel Fuel ◽  
Jatropha Oil ◽  
Reaction Parameters

This paper investigated the three critical reaction parameters including catalyst concentration, microwave exit power and reaction time for the transesterification process of jatropha curcas oil using microwave irradiation. The work is an attempt to reduce the production cost of biodiesel. Similar quantities of methanol to oil molar ratio 6:1 and calcium oxide as a heterogeneous catalyst were used. The results showed that the best yield percentage 96% was obtained using 300W microwave exit power, 8 %wt CaO and 7 min. The methyl ester FAME obtained was within the standard of biodiesel fuel.

scholarly journals Optimization of Enzymatic Synthesis of Betulinic Acid Amide in Organic Solvent by Response Surface Methodology (RSM)

2019 ◽  
Vol 19 (4) ◽  
pp. 849
Author(s):  
Nurul Atikah Amin Yusof ◽  
Nursyamsyila Mat Hadzir ◽  
Siti Efliza Ashari ◽  
Nor Suhaila Mohamad Hanapi ◽  
Rossuriati Dol Hamid
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Reaction Temperature ◽  
Betulinic Acid ◽  
Enzymatic Synthesis ◽  
Acid Amide ◽  
Molar Ratio ◽  
Percentage Yield ◽  
Substrate Molar Ratio

Optimization of the lipase catalyzed enzymatic synthesis of betulinic acid amide in the presence of immobilized lipase, Novozym 435 from Candida antartica as a biocatalyst was studied. Response surface methodology (RSM) and 5-level-4-factor central-composite rotatable design (CCRD) were employed to evaluate the effects of the synthesis parameters, such as reaction time (20–36 h), reaction temperature (37–45 °C), substrate molar ratio of betulinic acid to butylamine (1:1–1:3), and enzyme amounts (80–120 mg) on the percentage yield of betulinic acid amide by direct amidation reaction. The optimum conditions for synthesis were: reaction time of 28 h 33 min, reaction temperature of 42.92 °C, substrate molar ratio of 1:2.21, and enzyme amount of 97.77 mg. The percentage yield of actual experimental values obtained 65.09% which compared well with the maximum predicted value of 67.23%. The obtained amide was characterized by GC, GCMS and 13C NMR. Betulinic acid amide (BAA) showed a better cytotoxicity compared to betulinic acid as the concentration inhibited 50% of the cell growth (IC50) against MDA-MB-231 cell line (IC50 < 30 µg/mL).

scholarly journals Sol-Gel Immobilisation of Lipases: Towards Active and Stable Biocatalysts for the Esterification of Valeric Acid

Molecules ◽  
2018 ◽  
Vol 23 (9) ◽  
pp. 2283 ◽  
Author(s):  
Soledad Cebrián-García ◽  
Alina Balu ◽  
Araceli García ◽  
Rafael Luque
Keyword(s):  
Microwave Irradiation ◽  
Sol Gel ◽  
Valeric Acid ◽  
Added Value ◽  
Conventional Heating ◽  
Molar Ratio ◽  
Highly Active ◽  
Industrial Sectors ◽  
Wide Range ◽  
Acid Esterification

Alkyl esters are high added value products useful in a wide range of industrial sectors. A methodology based on a simple sol-gel approach (biosilicification) is herein proposed to encapsulate enzymes in order to design highly active and stable biocatalysts. Their performance was assessed through the optimization of valeric acid esterification evaluating the effect of different parameters (biocatalyst load, presence of water, reaction temperature and stirring rate) in different alcoholic media, and comparing two different methodologies: conventional heating and microwave irradiation. Ethyl valerate yields were in the 80–85% range under optimum conditions (15 min, 12% m/v biocatalyst, molar ratio 1:2 of valeric acid to alcohol). Comparatively, the biocatalysts were slightly deactivated under microwave irradiation due to enzyme denaturalisation. Biocatalyst reuse was attempted to prove that good reusability of these sol-gel immobilised enzymes could be achieved under conventional heating.

scholarly journals Interesterification of Egg-Yolk Phosphatidylcholine with p-Methoxycinnamic Acid Catalyzed by Immobilized Lipase B from Candida Antarctica

Catalysts ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1181
Author(s):  
Magdalena Rychlicka ◽  
Anna Gliszczyńska
Keyword(s):  
Reaction Time ◽  
Design Method ◽  
Immobilized Lipase ◽  
Reaction Medium ◽  
Solvent System ◽  
Novozym 435 ◽  
Molar Ratio ◽  
Binary Solvent ◽  
Methoxycinnamic Acid ◽  
Substrate Molar Ratio

The p-methoxycinnamic acid (p-MCA) is one of the most popular phenylpropanoids, the beneficial impact of which on the human health is well documented in the literature. This compound has shown many valuable activities including anticancer, antidiabetic, and neuro- and hepatoprotective. However, its practical application is limited by its low bioavailability resulting from rapid metabolism in the human body. The latest strategy, aimed at overcoming these limitations, is based on the production of more stability in systemic circulation bioconjugates with phospholipids. Therefore, the aim of this research was to develop the biotechnological method for the synthesis of phospholipid derivatives of p-methoxycinnamic acid, which can play a role of new nutraceuticals. We developed and optimized enzymatic interesterification of phosphatidylcholine (PC) with ethyl p-methoxycinnamate (Ep-MCA). Novozym 435 and a binary solvent system of toluene/chloroform 9:1 (v/v) were found to be the effective biocatalyst and reaction medium for the synthesis of structured p-MCA phospholipids, respectively. The effects of the other reaction parameters, such as substrate molar ratio, enzyme dosage, and reaction time, on the degree of incorporation of p-MCA into PC were evaluated by use of an experimental factorial design method. The results showed that substrate molar ratio and biocatalyst load have significant effects on the synthesis of p-methoxycinnamoylated phospholipids. The optimum conditions were: Reaction time of three days, 30% (w/w) of Novozym 435, and 1/10 substrate molar ratio PC/Ep-MCA. Under these parameters, p-methoxycinnamoylated lysophosphatidylcholine (p-MCA-LPC) and p-methoxycinnamoylated phosphatidylcholine (p-MCA-PC) were obtained in isolated yields of 32% and 3% (w/w), respectively.

Sign in / Sign up

Export Citation Format

Share Document