scholarly journals Effect of Growth Interruption on Surface Recombination Velocity in GaInAsSb/AlGaAsSb Heterostructures Grown by Organometallic Vapor Phase Epitaxy

2004 ◽  
Author(s):  
CA Wang ◽  
DA Shiau ◽  
D Donetsky ◽  
S Anikeev ◽  
G Belenky ◽  
...  
Keyword(s):  
Vapor Phase ◽  
Surface Recombination ◽  
Vapor Phase Epitaxy ◽  
Surface Recombination Velocity ◽  
Organometallic Vapor Phase Epitaxy ◽  
Growth Interruption ◽  
Recombination Velocity

scholarly journals Numerical Simulation Analysis of Ag Crystallite Effects on Interface of Front Metal and Silicon in the PERC Solar Cell

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 592
Author(s):  
Myeong Sang Jeong ◽  
Yonghwan Lee ◽  
Ka-Hyun Kim ◽  
Sungjin Choi ◽  
Min Gu Kang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Surface Recombination ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Metal Interface ◽  
Ag Crystallites ◽  
Recombination Velocity

In the fabrication of crystalline silicon solar cells, the contact properties between the front metal electrode and silicon are one of the most important parameters for achieving high-efficiency, as it is an integral element in the formation of solar cell electrodes. This entails an increase in the surface recombination velocity and a drop in the open-circuit voltage of the solar cell; hence, controlling the recombination velocity at the metal-silicon interface becomes a critical factor in the process. In this study, the distribution of Ag crystallites formed on the silicon-metal interface, the surface recombination velocity in the silicon-metal interface and the resulting changes in the performance of the Passivated Emitter and Rear Contact (PERC) solar cells were analyzed by controlling the firing temperature. The Ag crystallite distribution gradually increased corresponding to a firing temperature increase from 850 ∘C to 950 ∘C. The surface recombination velocity at the silicon-metal interface increased from 353 to 599 cm/s and the open-circuit voltage of the PERC solar cell decreased from 659.7 to 647 mV. Technology Computer-Aided Design (TCAD) simulation was used for detailed analysis on the effect of the surface recombination velocity at the silicon-metal interface on the PERC solar cell performance. Simulations showed that the increase in the distribution of Ag crystallites and surface recombination velocity at the silicon-metal interface played an important role in the decrease of open-circuit voltage of the PERC solar cell at temperatures of 850–900 ∘C, whereas the damage caused by the emitter over fire was determined as the main cause of the voltage drop at 950 ∘C. These results are expected to serve as a steppingstone for further research on improvement in the silicon-metal interface properties of silicon-based solar cells and investigation on high-efficiency solar cells.

Investigation of Surface Passivation in InAs/GaSb Strained-Layer-Superlattices Using Picosecond Excitation Correlation Measurement and Variable-Area Diode Array Surface Recombination Velocity Measurement

2005 ◽  
Vol 891 ◽  
Author(s):  
Zhimei Zhu ◽  
Elena Plis ◽  
Abdenour Amtout ◽  
Pallab Bhattacharya ◽  
Sanjay Krishna
Keyword(s):  
Infrared Detectors ◽  
Surface Passivation ◽  
Surface Recombination ◽  
Surface States ◽  
Depletion Region ◽  
Surface Recombination Velocity ◽  
Diode Array ◽  
Ammonium Sulfide ◽  
Picosecond Excitation ◽  
Recombination Velocity

ABSTRACTThe effect of ammonium sulfide passivation on InAs/GaSb superlattice infrared detectors was investigated using two complementary techniques, namely, picosecond excitation correlation (PEC) measurement and variable-area diode array (VADA) surface recombination velocity (SRV) measurement. PEC measurements were conducted on etched InAs/GaSb superlattice mesas, which were passivated in aqueous ammonium sulfide solutions of various strengths for several durations. The PEC signal's decay time constant (DTC) is proportional to carrier lifetimes. At 77 K the PEC signal's DTC of the as-grown InAs/GaSb superlattice sample was 2.0 ns, while that of the unpassivated etched sample was reduced to 1.2 ns by the surface states at the mesa sidewalls. The most effective ammonium sulfide passivation process increased the PEC signal's DTC to 10.4 ns. However it is difficult to isolate surface recombination from other processes that contribute to the lifetime using the PEC data, therefore a VADA SRV measurement was undertaken to determine the effect of passivation on surface recombination. The obtained SRV in the depletion region of the InAs/GaSb superlattice and GaSb junction was 1.1×106 cm/s for the unpassivated sample and 4.6×105 cm/s for the passivated sample. At 77 K the highest R0A value measured in our passivated devices was 2540 W cm2 versus 0.22 W cm2 for the unpassivated diodes. The results of the lifetime, the SRV and the R0A measurements indicate that ammonium sulfide passivation will improve the performance of InAs/GaSb superlattice infrared detectors.

IR and MW Absorption Techniques for Bulk and Surface Recombination Control in High-Quaiity Silicon

1995 ◽  
Vol 386 ◽  
Author(s):  
A. Kaniava ◽  
U. Menczigar ◽  
J. Vanhellemont ◽  
J. Poortmans ◽  
A. L. P. Rotondaro ◽  
...  
Keyword(s):  
Surface Recombination ◽  
Surface Recombination Velocity ◽  
Silicon Substrates ◽  
Injection Level ◽  
Effective Lifetime ◽  
Carrier Recombination ◽  
High Injection Level ◽  
High Injection ◽  
Wide Range ◽  
Recombination Velocity

ABSTRACTThe carrier recombination rate in high-quality FZ and Cz silicon substrates is studied by contactless infrared and microwave absorption techniques. Different surface treatments covering a wide range of surface recombination velocity have been used for the separation of bulk and surface recombination components and evaluating of the efficiency of passivation. Limitations of effective lifetime approach are analyzed specific for low and high injection level. Sensitivity limits of the techniques for iron contamination are discussed

Sign in / Sign up

Export Citation Format

Share Document