Treatment of low and medium strength sewage in a lab-scale gradual concentric chambers (GCC) reactor

2008 ◽  
Vol 57 (8) ◽  
pp. 1155-1160 ◽  
Author(s):  
L. Mendoza ◽  
M. Carballa ◽  
L. Zhang ◽  
W. Verstraete
Keyword(s):  
Removal Efficiency ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Organic Loading Rate ◽  
Medium Strength ◽  
Low Strength ◽  
And Performance ◽  
Scale Design ◽  
Final Effluent

One of the major challenges of anaerobic technology is its applicability for low strength wastewaters, such as sewage. The lab-scale design and performance of a novel Gradual Concentric Chambers (GCC) reactor treating low (165±24 mg COD/L) and medium strength (550 mg COD/L) domestic wastewaters were studied. Experimental data were collected to evaluate the influence of chemical oxygen demand (COD) concentrations in the influent and the hydraulic retention time (HRT) on the performance of the GCC reactor. Two reactors (R1 and R2), integrating anaerobic and aerobic processes, were studied at ambient (26°C) and mesophilic (35°C) temperature, respectively. The highest COD removal efficiency (94%) was obtained when treating medium strength wastewater at an organic loading rate (OLR) of 1.9 g COD/L·d (HRT = 4 h). The COD levels in the final effluent were around 36 mg/L. For the low strength domestic wastewater, a highest removal efficiency of 85% was observed, producing a final effluent with 22 mg COD/L. Changes in the nutrient concentration levels were followed for both reactors.

Two-stage entrapped mixed microbial cell process for simultaneous removal of organics and nitrogen for rural domestic sewage application

2004 ◽  
Vol 49 (5-6) ◽  
pp. 281-288 ◽  
Author(s):  
S.J. Kim ◽  
P.Y. Yang
Keyword(s):  
Removal Efficiency ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Microbial Cell ◽  
Two Stage ◽  
Rate Limiting Step ◽  
Soluble Chemical Oxygen Demand ◽  
Removal Efficiencies ◽  
Entrapped Mixed Microbial Cell

A two-stage entrapped mixed microbial cell (2SEMMC) process which separates nitrification and denitrification phases by the installation of the anoxic and oxic EMMC reactors packed with EMMC carriers was operated with 6, 4, 3, and 2 hours of hydraulic retention time (HRT) using simulated domestic wastewater. The activated sludge was immobilized using cellulose acetate for the EMMC carriers. Similar soluble chemical oxygen demand (SCOD) removal efficiencies of 90-97% were observed for all HRTs (SCOD loading rate of 0.84-2.30 g/L/d) applied. In order to achieve more than 80 % of TN removal efficiency, the HRT should be maintained higher than 4 hours (less than 0.24 g/L/d of TN loading rate). Denitrification was a rate-limiting step which controlled overall TN removal efficiency at TN loading rate of 0.15-0.31 g/L/d although nitrification efficiencies achieved 97-99 %. The effluent TSS of less than 25 mg/L in the 2SEMMC process was maintained at the SCOD loading rate of less than 1.23 g/L/d with back-washing intervals of 5 and 10 days in the anoxic and oxic EMMC reactors, respectively. The minimum HRT of 4 hours is required for high removal efficiencies of organics (average 95.6 %) and nitrogen (average 80.5 %) in the 2SEMMC process with 3 times of recirculation ratio.

Septic Tank Effluent Treatment by Subsurface Horizontal Flow Wetland

2010 ◽  
Vol 5 (4) ◽  
Author(s):  
Ellina S. Pandebesie ◽  
Ni Wayan Budi Arie
Keyword(s):  
Ground Water ◽  
Removal Efficiency ◽  
Open Space ◽  
Loading Rate ◽  
Domestic Wastewater ◽  
Septic Tank ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Septic Tank Effluent ◽  
Bod Removal

Domestic wastewater treatment in Indonesia, mostly treat by using septic tanks. The use of septic tanks preferred by the public because of the design, construction, and maintenance are easy and more economical for the system of domestic wastewater disposal. Effluent from the septic tank still contains BOD about 100 mg /l, COD about 250 mg/l and TSS about 100 mg /l. This effluent is still dangerous to public health and is not fulfill wastewater effluent standards yet. If there is open space available, extended treatment of septic tank effluent can be done by field infiltration. This open space must suitable for infiltration without contaminating the ground water or well water. In urban areas with ground water level is high such as Surabaya, water infiltrate into the ground causing the problem. Problems that arise are due to pollution of ground water and surface water contaminated by effluent from the septic tank. Because of these problems, it would require an alternative treatment of septic tank effluent. Appropriate technology would be a simple, economical, easy in operation and maintenance. One of wastewater processing that can be applied to the septic tank effluent is a constructed wetland system. Previous research carried out by using Cyperus papyrus plant with sand media in batch experiments showed satisfactory results. In this study, experiments conducted by using Cyperus papyrus plant with sand media with continuous flow in a horizontal subsurface flow wetland method. Wastewater flows with varying flow 90 ml /min and 180 ml /min. The objective of this research is to determine the ability of a horizontal subsurface flow wetland for treating septic tank effluent. The parameters analyzed were BOD and TSS. The results show the relation of organic loading rate with BOD removal efficiency. The highest organic loading rate of 0.051 kg BOD/m2.d on first day observations has BOD removal efficiency of 73.63% and the lowest organic loading rate of 0.029 kg BOD/m2.d with an efficiency of 70.82%. This shows that BOD removal efficiency is affected by organic loading rate. If BOD loading rate increase, it will decrease BOD removal efficiency. Organic loading rate recommended for domestic wastewater is 0.037-0.4 kg BOD5 /m2.d. Although in this study the organic loading rate exceeds the above recommendations, but efficiency is still good, above 70%.

Anaerobic degradation of carbon capture reclaimer MEA waste

2013 ◽  
Vol 67 (11) ◽  
pp. 2549-2559 ◽  
Author(s):  
S. Wang ◽  
J. Hovland ◽  
R. Bakke
Keyword(s):  
Removal Efficiency ◽  
Carbon Capture ◽  
Loading Rate ◽  
Nitrogen Concentration ◽  
Oxygen Demand ◽  
Ammonia Nitrogen ◽  
Cod Removal ◽  
Methane Yield ◽  
Organic Loading Rate ◽  
Cod Removal Efficiency

The anaerobic biodegradation of reclaimer MEA (monoethanolamine) waste (MEAw) with easily degradable co-substrates was investigated in a laboratory-scale bioreactor at room temperature during a 160 d experimental run. The reactor that was constructed with three phases to facilitate attached biofilm and suspended biomass retention for degradation of the complex and challenging MEAw performed well. A feed strategy of step-wise increasing organic loading rate (OLR) by either increasing feed MEAw concentration or the hydraulic loading rate was applied. The system performance was evaluated by chemical oxygen demand (COD) removal efficiency, methane yield, MEA removal, and the accumulation of ammonia and volatile fatty acid (VFA). The total COD removal efficiency initially was 93% when the feed was mainly easily degradable co-substrate. The total removal dropped to 75% at the end when MEAw constituted 60% of the feed COD. Ion chromatography results show that the MEA and some unidentified feed chemicals were almost completely consumed. The main products of MEAw degradation were ammonia, VFAs and biogas. The ammonia nitrogen concentration reached about 2.0 g/L, which may explain the observed inhibition of acetoclastic methanogenesis leading to acetate accumulation. Methane accounted for up to 80% of the biogas generated. The highest methane yield was 0.34 L/g-COD while the yield was 0.16 L/g-COD at the highest load. This study shows that more than 80% reclaimer MEAw COD degradation with a co-substrate can be maintained in a hybrid anaerobic bioreactor operated in a wide loading range.

Treatment of Low-Strength Wastewater Using an Anaerobic Baffled Reactor at Low Temperature

2013 ◽  
Vol 325-326 ◽  
pp. 822-826
Author(s):  
Zong Lian She ◽  
Xiao Hui Fu ◽  
Jian Wu ◽  
En Shi ◽  
Lai Li Zhao ◽  
...  
Keyword(s):  
Low Temperature ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Granular Sludge ◽  
Organic Loading Rate ◽  
Scanning Electron Micrographs ◽  
Organic Loading ◽  
Microbial Composition ◽  
Anaerobic Baffled Reactor ◽  
Low Strength

Treatment of low-strength wastewater of chemical oxygen demand (COD) around 500-1500 mg/L was studied in a 100 L capacity laboratory scale anaerobic baffled reactor (four compartments) at low temperature (17 oC-25 oC). The reactor was operated at influent COD concentrations of 1500, 1000 and 500 mg/L and hydraulic retention times (HRTs) of 24, 12 and 8 h, with the average COD removals changing from 94% to 83%. Compartment-wise studies of various parameters revealed that if the organic loading rate (OLR) was larger, the initial compartment played significant role in the removal of organics. The examinations of scanning electron micrographs (SEM) indicated that the microbial composition of granular sludge were obviously different in four compartments.

scholarly journals Experiences on the implementation of a pilot grey water treatment and reuse based system at a household in the slum of Kyebando-Kisalosalo, Kampala

2014 ◽  
Vol 4 (4) ◽  
pp. 294-307 ◽  
Author(s):  
Charles B. Niwagaba ◽  
Patrick Dinno ◽  
Isaac Wamala ◽  
S. Sahar Dalahmeh ◽  
Cecilia Lalander ◽  
...  
Keyword(s):  
Loading Rate ◽  
Type System ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Organic Loading Rate ◽  
Surface Irrigation ◽  
Limited Effect ◽  
Grey Water ◽  
Multi Media ◽  
Removal Efficiencies

Grey water constitutes the largest fraction of domestic wastewater. It causes environmental sanitation and pollution problems if it is not managed well. If treated, grey water can be a resource for a variety of uses. A pilot system was constructed in February 2013 to treat grey water from a four-member household for sub-surface irrigation of local vegetables. A hydraulic loading rate (HLR) of 60 L m−2d−1 and an organic loading rate (OLR) of 519–1,580 g BOD5m−2d−1 were implemented on a multi-media filter of gravel, charcoal, geotextile and mulch (charcoal being the predominant layer) operated as a batched type-system, with a 36-hour retention time. The system was operated for 3 months, during which it showed remarkable removal efficiencies of 90.8 ± 5.4 and 96.1 ± 3.0% after 36 hours for chemical oxygen demand (COD) and biochemical oxygen demand (BOD), respectively, and 95 ± 3.1% for faecal coliforms (FC). The removal efficiencies at 36 hours, of total nitrogen (TN), total phosphorus (Tot-P), total suspended solids (TSS) and total dissolved solids (TDS) were 39.0, 30.1, 85.2 and 78.6%, respectively. Plant response to sub-surface irrigation with treated grey water was largely masked by rainy season and the effluent had a limited effect on the soil.

scholarly journals Development of downflow hanging sponge (DHS) reactor as post treatment of existing combined anaerobic tank treating natural rubber processing wastewater

2016 ◽  
Vol 75 (1) ◽  
pp. 57-68 ◽  
Author(s):  
Takahiro Watari ◽  
Trung Cuong Mai ◽  
Daisuke Tanikawa ◽  
Yuga Hirakata ◽  
Masashi Hatamoto ◽  
...  
Keyword(s):  
Natural Rubber ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Nitrogen Loading ◽  
Post Treatment ◽  
Organic Loading Rate ◽  
Anammox Bacteria ◽  
Rrna Gene ◽  
Sequencing Analysis ◽  
Reactor Performance

Conventional aerated tank technology is widely applied for post treatment of natural rubber processing wastewater in Southeast Asia; however, a long hydraulic retention time (HRT) is required and the effluent standards are exceeded. In this study, a downflow hanging sponge (DHS) reactor was installed as post treatment of anaerobic tank effluent in a natural rubber factory in South Vietnam and the process performance was evaluated. The DHS reactor demonstrated removal efficiencies of 64.2 ± 7.5% and 55.3 ± 19.2% for total chemical oxygen demand (COD) and total nitrogen, respectively, with an organic loading rate of 0.97 ± 0.03 kg-COD m−3 day−1 and a nitrogen loading rate of 0.57 ± 0.21 kg-N m−3 day−1. 16S rRNA gene sequencing analysis of the sludge retained in the DHS also corresponded to the result of reactor performance, and both nitrifying and denitrifying bacteria were detected in the sponge carrier. In addition, anammox bacteria was found in the retained sludge. The DHS reactor reduced the HRT of 30 days to 4.8 h compared with the existing algal tank. This result indicates that the DHS reactor could be an appropriate post treatment for the existing anaerobic tank for natural rubber processing wastewater treatment.

scholarly journals The Concept of Wastes to Energy Using Sugary Wastes

2012 ◽  
Vol 9 ◽  
pp. 57-62
Author(s):  
Fiza Sarwar ◽  
Wajeeha Malik ◽  
Muhammad Salman Ahmed ◽  
Harja Shahid
Keyword(s):  
Volatile Fatty Acids ◽  
Loading Rate ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Loading Rates ◽  
Sugar Mills ◽  
Anaerobic Sludge Blanket

Abstract: This study was designed using actual effluent from the sugary mills in an Up-flow Anaerobic Sludge Blanket (UASB) Reactor to evaluate treatability performance. The reactor was started-up in step-wise loading rates beginning from 0.05kg carbon oxygen demand (COD)/m3-day to 3.50kg-COD/m3-day. The hydraulic retention time (HRT) was slowly decreased from 96 hrs to eight hrs. It was observed that the removal efficiency of COD of more than 73% can be easily achieved at an HRT of more than 16 hours corresponding to an average organic loading rate (OLR) of 3.0kg-COD/m3-day, at neutral pH and constant temperature of 29°C. The average VFAs (volatile fatty acids) and biogas production was observed as 560mg/L and 1.6L/g-CODrem-d, respectively. The average methane composition was estimated as 62%. The results of this study suggest that the treatment of sugar mills effluent with the anaerobic technology seems to be more reliable, effective and economical.DOI: http://dx.doi.org/10.3126/hn.v9i0.7075 Hydro Nepal Vol.9 July 2011 57-62

Open trickling filter: an innovative, cheap and simple form of post-treatment of sanitary effluents from anaerobic reactors in small communities

2012 ◽  
Vol 2 (2) ◽  
pp. 59-67 ◽  
Author(s):  
P. C. Vieira ◽  
M. von Sperling
Keyword(s):  
Loading Rate ◽  
Oxygen Demand ◽  
Post Treatment ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Trickling Filter ◽  
Small Communities ◽  
Capital Costs

We aimed to evaluate the performance and cost savings of an innovative design of a trickling filter (TF) for small population sizes, developed at the Federal University of Minas Gerais, Brazil referred to as an open trickling filter (OTF). The OTF had no side walls and no perforated bottom slab, and was applied for the post-treatment of sanitary sewage from an upflow anaerobic sludge blanket (UASB) reactor. The OTF had crushed-stone packing (3.5 m high) and was operated with an average surface hydraulic loading rate of 4.1 m3 m−2 d−1 and an average volumetric organic loading rate of 0.10 kg BOD m−3 d−1 (biochemical oxygen demand). The average concentrations obtained at the OTF effluent were 48 mg TSS L−1 (total suspended solids), 132 mg COD L−1 (chemical oxygen demand), 51 mg BOD L−1, 19 mg TKN L−1 (total Kjeldahl nitrogen), 16 mg NH4+-N L−1 and 10 mg NO3−-N L−1, complying with local discharge standards. Analysis of the construction costs indicated savings of 74% compared to conventional TF. Based on the performance, compactness, simplicity and reduced capital costs, it is believed that the proposed OTF is a good alternative for small communities, especially in developing countries.

Biological wastewater treatment for removal of polymeric resins in UASB reactor: influence of oxygen

2008 ◽  
Vol 57 (7) ◽  
pp. 1047-1052 ◽  
Author(s):  
U. Durán ◽  
O. Monroy ◽  
J. Gómez ◽  
F. Ramírez
Keyword(s):  
Acrylic Acid ◽  
Vinyl Acetate ◽  
Removal Efficiency ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Uasb Reactor ◽  
Cod Removal Efficiency ◽  
Consumption Rates ◽  
Polymeric Resins

The biological elimination of polymeric resins compounds (PRC) such as acrylic acid and their esters, vinyl acetate and styrene under methanogenic and oxygen-limited methanogenesis conditions was evaluated. Two UASB reactors (A and B) were used and the removal of the organic matter was studied in four stages. Reactor A was used as methanogenic control during the study. Initially both reactors were operated under methanogenic conditions. From the second stage reactor B was fed with 0.6 and 1 mg/L·d of oxygen (O2). Reactor A had diminution in chemical oxygen demand (COD) removal efficiency from 75±4% to 37±5%, by the increase of PRC loading rate from 750 to 1125 mg COD/L·d. In this reactor there was no styrene elimination. In reactor B the COD removal efficiency was between 73±5% and 80±2%, even with the addition of O2 and increase of the PRC loading rate, owing to oxygen being used in the partial oxidation of these compounds. In this reactor the yields were modified from 0.56 to 0.40 for CH4 and from 0.31 to 0.60 for CO2. The O2 in low concentrations increased 40.7% the consumption rates of acrylic acid, methyl acrylate and vinyl acetate, allowing styrene consumption with a rate of 0.103 g/L·d. Batch cultures demonstrated that under methanogenic and oxygen-limited methanogenesis conditions, the glucose was not used as an electron acceptor in the elimination of PRC.

Working Parameters Optimization of Hydrolysis-acidogenesis reactor in two stage anaerobic digestion of slaughterhouse Wastewater for Biogas Production

2020 ◽  
Author(s):  
Dejene Tsegaye Bedane ◽  
Mohammed Mazharuddin Khan ◽  
Seyoum Leta Asfaw
Keyword(s):  
Anaerobic Digestion ◽  
Working Conditions ◽  
Retention Time ◽  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Slaughterhouse Wastewater ◽  
Working Parameters

Abstract Background : Wastewater from agro-industries such as slaughterhouse is typical organic wastewater with high value of biochemical oxygen demand, chemical oxygen demand, biological organic nutrients (Nitrogen and phosphate) which are insoluble, slowly biodegradable solids, pathogenic and non-pathogenic bacteria and viruses, parasite eggs. Moreover it contains high protein and putrefies fast leading to environmental pollution problem. This indicates that slaughterhouses are among the most environmental polluting agro-industries. Anaerobic digestion is a sequence of metabolic steps involving consortiums of several microbial populations to form a complex metabolic interaction network resulting in the conversation of organic matter into methane (CH 4 ), carbon dioxide (CO 2 ) and other trace compounds. Separation of the phase permits the optimization of the organic loading rate and HRT based on the requirements of the microbial consortiums of each phase. The purpose of this study was to optimize the working conditions for the hydrolytic - acidogenic stage in two step/phase anaerobic digestion of slaughterhouse wastewater. The setup of the laboratory scale reactor was established at Center for Environmental Science, College of Natural Science with a total volume of 40 liter (36 liter working volume and 4 liter gas space). The working parameters for hydrolytic - acidogenic stage were optimized for six hydraulic retention time 1-6 days and equivalent organic loading rate of 5366.43 – 894.41 mg COD/L day to evaluate the effect of the working parameters on the performance of hydrolytic – acidogenic reactor. Result : The finding revealed that hydraulic retention time of 3 day with organic loading rate of 1,788.81 mg COD/L day was a as an optimal working conditions for the parameters under study for the hydrolytic - acidogenic stage. The degree of hydrolysis and acidification were mainly influenced by lower hydraulic retention time (higher organic loading rate) and highest values recorded were 63.92 % at hydraulic retention time of 3 day and 53.26% at hydraulic retention time of 2 day respectively. Conclusion : The finding of the present study indicated that at steady state the concentration of soluble chemical oxygen demand and total volatile fatty acids increase as hydraulic retention time decreased or organic loading rate increased from 1 day hydraulic retention time to 3 day hydraulic retention time and decreases as hydraulic retention time increase from 4 to 6 day. The lowest concentration of NH 4 + -N and highest degree of acidification was also achieved at hydraulic retention time of 3 day. Therefore, it can be concluded that hydraulic retention time of 3 day/organic loading rate of 1,788.81 mg COD/L .day was selected as an optimal working condition for the high performance and stability during the two stage anaerobic digestion of slaughterhouse wastewater for the hydrolytic-acidogenic stage under mesophilic temperature range selected (37.5℃). Keywords : Slaughterhouse Wastewater, Hydrolytic – Acidogenic, Two Phase Anaerobic Digestion, Optimal Condition, Agro-processing wastewater

Sign in / Sign up

Export Citation Format

Share Document