scholarly journals Experiences on the implementation of a pilot grey water treatment and reuse based system at a household in the slum of Kyebando-Kisalosalo, Kampala

2014 ◽  
Vol 4 (4) ◽  
pp. 294-307 ◽  
Author(s):  
Charles B. Niwagaba ◽  
Patrick Dinno ◽  
Isaac Wamala ◽  
S. Sahar Dalahmeh ◽  
Cecilia Lalander ◽  
...  
Keyword(s):  
Loading Rate ◽  
Type System ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Organic Loading Rate ◽  
Surface Irrigation ◽  
Limited Effect ◽  
Grey Water ◽  
Multi Media ◽  
Removal Efficiencies

Grey water constitutes the largest fraction of domestic wastewater. It causes environmental sanitation and pollution problems if it is not managed well. If treated, grey water can be a resource for a variety of uses. A pilot system was constructed in February 2013 to treat grey water from a four-member household for sub-surface irrigation of local vegetables. A hydraulic loading rate (HLR) of 60 L m−2d−1 and an organic loading rate (OLR) of 519–1,580 g BOD5m−2d−1 were implemented on a multi-media filter of gravel, charcoal, geotextile and mulch (charcoal being the predominant layer) operated as a batched type-system, with a 36-hour retention time. The system was operated for 3 months, during which it showed remarkable removal efficiencies of 90.8 ± 5.4 and 96.1 ± 3.0% after 36 hours for chemical oxygen demand (COD) and biochemical oxygen demand (BOD), respectively, and 95 ± 3.1% for faecal coliforms (FC). The removal efficiencies at 36 hours, of total nitrogen (TN), total phosphorus (Tot-P), total suspended solids (TSS) and total dissolved solids (TDS) were 39.0, 30.1, 85.2 and 78.6%, respectively. Plant response to sub-surface irrigation with treated grey water was largely masked by rainy season and the effluent had a limited effect on the soil.

Two-stage entrapped mixed microbial cell process for simultaneous removal of organics and nitrogen for rural domestic sewage application

2004 ◽  
Vol 49 (5-6) ◽  
pp. 281-288 ◽  
Author(s):  
S.J. Kim ◽  
P.Y. Yang
Keyword(s):  
Removal Efficiency ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Microbial Cell ◽  
Two Stage ◽  
Rate Limiting Step ◽  
Soluble Chemical Oxygen Demand ◽  
Removal Efficiencies ◽  
Entrapped Mixed Microbial Cell

A two-stage entrapped mixed microbial cell (2SEMMC) process which separates nitrification and denitrification phases by the installation of the anoxic and oxic EMMC reactors packed with EMMC carriers was operated with 6, 4, 3, and 2 hours of hydraulic retention time (HRT) using simulated domestic wastewater. The activated sludge was immobilized using cellulose acetate for the EMMC carriers. Similar soluble chemical oxygen demand (SCOD) removal efficiencies of 90-97% were observed for all HRTs (SCOD loading rate of 0.84-2.30 g/L/d) applied. In order to achieve more than 80 % of TN removal efficiency, the HRT should be maintained higher than 4 hours (less than 0.24 g/L/d of TN loading rate). Denitrification was a rate-limiting step which controlled overall TN removal efficiency at TN loading rate of 0.15-0.31 g/L/d although nitrification efficiencies achieved 97-99 %. The effluent TSS of less than 25 mg/L in the 2SEMMC process was maintained at the SCOD loading rate of less than 1.23 g/L/d with back-washing intervals of 5 and 10 days in the anoxic and oxic EMMC reactors, respectively. The minimum HRT of 4 hours is required for high removal efficiencies of organics (average 95.6 %) and nitrogen (average 80.5 %) in the 2SEMMC process with 3 times of recirculation ratio.

Treatment of low and medium strength sewage in a lab-scale gradual concentric chambers (GCC) reactor

2008 ◽  
Vol 57 (8) ◽  
pp. 1155-1160 ◽  
Author(s):  
L. Mendoza ◽  
M. Carballa ◽  
L. Zhang ◽  
W. Verstraete
Keyword(s):  
Removal Efficiency ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Organic Loading Rate ◽  
Medium Strength ◽  
Low Strength ◽  
And Performance ◽  
Scale Design ◽  
Final Effluent

One of the major challenges of anaerobic technology is its applicability for low strength wastewaters, such as sewage. The lab-scale design and performance of a novel Gradual Concentric Chambers (GCC) reactor treating low (165±24 mg COD/L) and medium strength (550 mg COD/L) domestic wastewaters were studied. Experimental data were collected to evaluate the influence of chemical oxygen demand (COD) concentrations in the influent and the hydraulic retention time (HRT) on the performance of the GCC reactor. Two reactors (R1 and R2), integrating anaerobic and aerobic processes, were studied at ambient (26°C) and mesophilic (35°C) temperature, respectively. The highest COD removal efficiency (94%) was obtained when treating medium strength wastewater at an organic loading rate (OLR) of 1.9 g COD/L·d (HRT = 4 h). The COD levels in the final effluent were around 36 mg/L. For the low strength domestic wastewater, a highest removal efficiency of 85% was observed, producing a final effluent with 22 mg COD/L. Changes in the nutrient concentration levels were followed for both reactors.

Enhanced removal of chemical oxygen demand, nitrogen and phosphorus using the ameliorative anoxic/anaerobic/oxic process and micro-electrolysis

2012 ◽  
Vol 66 (4) ◽  
pp. 850-857 ◽  
Author(s):  
K. Q. Bao ◽  
J. Q. Gao ◽  
Z. B. Wang ◽  
R. Q. Zhang ◽  
Z. Y. Zhang ◽  
...  
Keyword(s):  
Chemical Oxygen Demand ◽  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Synthetic Wastewater ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Nitrogen And Phosphorus ◽  
Operational Conditions ◽  
Removal Efficiencies

Synthetic wastewater was treated using a novel system integrating the reversed anoxic/anaerobic/oxic (RAAO) process, a micro-electrolysis (ME) bed and complex biological media. The system showed superior chemical oxygen demand (COD), total nitrogen (TN) and total phosphorus (TP) removal rates. Performance of the system was optimised by considering the influences of three major controlling factors, namely, hydraulic retention time (HRT), organic loading rate (OLR) and mixed liquor recirculation (MLR). TP removal efficiencies were 69, 87, 87 and 83% under the HRTs of 4, 8, 12 and 16 h. In contrast, HRT had negligible effects on the COD and TN removal efficiencies. COD, TN and TP removal efficiencies from synthetic wastewater were 95, 63 and 87%, respectively, at an OLR of 1.9 g/(L·d). The concentrations of COD, TN and TP in the effluent were less than 50, 15 and 1 mg/L, respectively, at the controlled MLR range of 75–100%. In this system, organics, TN and TP were primarily removed from anoxic tank regardless of the operational conditions.

scholarly journals Development of downflow hanging sponge (DHS) reactor as post treatment of existing combined anaerobic tank treating natural rubber processing wastewater

2016 ◽  
Vol 75 (1) ◽  
pp. 57-68 ◽  
Author(s):  
Takahiro Watari ◽  
Trung Cuong Mai ◽  
Daisuke Tanikawa ◽  
Yuga Hirakata ◽  
Masashi Hatamoto ◽  
...  
Keyword(s):  
Natural Rubber ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Nitrogen Loading ◽  
Post Treatment ◽  
Organic Loading Rate ◽  
Anammox Bacteria ◽  
Rrna Gene ◽  
Sequencing Analysis ◽  
Reactor Performance

Conventional aerated tank technology is widely applied for post treatment of natural rubber processing wastewater in Southeast Asia; however, a long hydraulic retention time (HRT) is required and the effluent standards are exceeded. In this study, a downflow hanging sponge (DHS) reactor was installed as post treatment of anaerobic tank effluent in a natural rubber factory in South Vietnam and the process performance was evaluated. The DHS reactor demonstrated removal efficiencies of 64.2 ± 7.5% and 55.3 ± 19.2% for total chemical oxygen demand (COD) and total nitrogen, respectively, with an organic loading rate of 0.97 ± 0.03 kg-COD m−3 day−1 and a nitrogen loading rate of 0.57 ± 0.21 kg-N m−3 day−1. 16S rRNA gene sequencing analysis of the sludge retained in the DHS also corresponded to the result of reactor performance, and both nitrifying and denitrifying bacteria were detected in the sponge carrier. In addition, anammox bacteria was found in the retained sludge. The DHS reactor reduced the HRT of 30 days to 4.8 h compared with the existing algal tank. This result indicates that the DHS reactor could be an appropriate post treatment for the existing anaerobic tank for natural rubber processing wastewater treatment.

scholarly journals The Concept of Wastes to Energy Using Sugary Wastes

2012 ◽  
Vol 9 ◽  
pp. 57-62
Author(s):  
Fiza Sarwar ◽  
Wajeeha Malik ◽  
Muhammad Salman Ahmed ◽  
Harja Shahid
Keyword(s):  
Volatile Fatty Acids ◽  
Loading Rate ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Loading Rates ◽  
Sugar Mills ◽  
Anaerobic Sludge Blanket

Abstract: This study was designed using actual effluent from the sugary mills in an Up-flow Anaerobic Sludge Blanket (UASB) Reactor to evaluate treatability performance. The reactor was started-up in step-wise loading rates beginning from 0.05kg carbon oxygen demand (COD)/m3-day to 3.50kg-COD/m3-day. The hydraulic retention time (HRT) was slowly decreased from 96 hrs to eight hrs. It was observed that the removal efficiency of COD of more than 73% can be easily achieved at an HRT of more than 16 hours corresponding to an average organic loading rate (OLR) of 3.0kg-COD/m3-day, at neutral pH and constant temperature of 29°C. The average VFAs (volatile fatty acids) and biogas production was observed as 560mg/L and 1.6L/g-CODrem-d, respectively. The average methane composition was estimated as 62%. The results of this study suggest that the treatment of sugar mills effluent with the anaerobic technology seems to be more reliable, effective and economical.DOI: http://dx.doi.org/10.3126/hn.v9i0.7075 Hydro Nepal Vol.9 July 2011 57-62

Open trickling filter: an innovative, cheap and simple form of post-treatment of sanitary effluents from anaerobic reactors in small communities

2012 ◽  
Vol 2 (2) ◽  
pp. 59-67 ◽  
Author(s):  
P. C. Vieira ◽  
M. von Sperling
Keyword(s):  
Loading Rate ◽  
Oxygen Demand ◽  
Post Treatment ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Trickling Filter ◽  
Small Communities ◽  
Capital Costs

We aimed to evaluate the performance and cost savings of an innovative design of a trickling filter (TF) for small population sizes, developed at the Federal University of Minas Gerais, Brazil referred to as an open trickling filter (OTF). The OTF had no side walls and no perforated bottom slab, and was applied for the post-treatment of sanitary sewage from an upflow anaerobic sludge blanket (UASB) reactor. The OTF had crushed-stone packing (3.5 m high) and was operated with an average surface hydraulic loading rate of 4.1 m3 m−2 d−1 and an average volumetric organic loading rate of 0.10 kg BOD m−3 d−1 (biochemical oxygen demand). The average concentrations obtained at the OTF effluent were 48 mg TSS L−1 (total suspended solids), 132 mg COD L−1 (chemical oxygen demand), 51 mg BOD L−1, 19 mg TKN L−1 (total Kjeldahl nitrogen), 16 mg NH4+-N L−1 and 10 mg NO3−-N L−1, complying with local discharge standards. Analysis of the construction costs indicated savings of 74% compared to conventional TF. Based on the performance, compactness, simplicity and reduced capital costs, it is believed that the proposed OTF is a good alternative for small communities, especially in developing countries.

Working Parameters Optimization of Hydrolysis-acidogenesis reactor in two stage anaerobic digestion of slaughterhouse Wastewater for Biogas Production

2020 ◽  
Author(s):  
Dejene Tsegaye Bedane ◽  
Mohammed Mazharuddin Khan ◽  
Seyoum Leta Asfaw
Keyword(s):  
Anaerobic Digestion ◽  
Working Conditions ◽  
Retention Time ◽  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Slaughterhouse Wastewater ◽  
Working Parameters

Abstract Background : Wastewater from agro-industries such as slaughterhouse is typical organic wastewater with high value of biochemical oxygen demand, chemical oxygen demand, biological organic nutrients (Nitrogen and phosphate) which are insoluble, slowly biodegradable solids, pathogenic and non-pathogenic bacteria and viruses, parasite eggs. Moreover it contains high protein and putrefies fast leading to environmental pollution problem. This indicates that slaughterhouses are among the most environmental polluting agro-industries. Anaerobic digestion is a sequence of metabolic steps involving consortiums of several microbial populations to form a complex metabolic interaction network resulting in the conversation of organic matter into methane (CH 4 ), carbon dioxide (CO 2 ) and other trace compounds. Separation of the phase permits the optimization of the organic loading rate and HRT based on the requirements of the microbial consortiums of each phase. The purpose of this study was to optimize the working conditions for the hydrolytic - acidogenic stage in two step/phase anaerobic digestion of slaughterhouse wastewater. The setup of the laboratory scale reactor was established at Center for Environmental Science, College of Natural Science with a total volume of 40 liter (36 liter working volume and 4 liter gas space). The working parameters for hydrolytic - acidogenic stage were optimized for six hydraulic retention time 1-6 days and equivalent organic loading rate of 5366.43 – 894.41 mg COD/L day to evaluate the effect of the working parameters on the performance of hydrolytic – acidogenic reactor. Result : The finding revealed that hydraulic retention time of 3 day with organic loading rate of 1,788.81 mg COD/L day was a as an optimal working conditions for the parameters under study for the hydrolytic - acidogenic stage. The degree of hydrolysis and acidification were mainly influenced by lower hydraulic retention time (higher organic loading rate) and highest values recorded were 63.92 % at hydraulic retention time of 3 day and 53.26% at hydraulic retention time of 2 day respectively. Conclusion : The finding of the present study indicated that at steady state the concentration of soluble chemical oxygen demand and total volatile fatty acids increase as hydraulic retention time decreased or organic loading rate increased from 1 day hydraulic retention time to 3 day hydraulic retention time and decreases as hydraulic retention time increase from 4 to 6 day. The lowest concentration of NH 4 + -N and highest degree of acidification was also achieved at hydraulic retention time of 3 day. Therefore, it can be concluded that hydraulic retention time of 3 day/organic loading rate of 1,788.81 mg COD/L .day was selected as an optimal working condition for the high performance and stability during the two stage anaerobic digestion of slaughterhouse wastewater for the hydrolytic-acidogenic stage under mesophilic temperature range selected (37.5℃). Keywords : Slaughterhouse Wastewater, Hydrolytic – Acidogenic, Two Phase Anaerobic Digestion, Optimal Condition, Agro-processing wastewater

scholarly journals Performance comparison of uninsulated and insulated hybrid anaerobic baffled reactor (HABR) operating at warm temperature

2018 ◽  
Vol 78 (9) ◽  
pp. 1879-1892 ◽  
Author(s):  
Md Khalekuzzaman ◽  
Muhammed Alamgir ◽  
Mehedi Hasan ◽  
Md Nahid Hasan
Keyword(s):  
Removal Efficiency ◽  
Suspended Solids ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Total Suspended Solids ◽  
Performance Comparison ◽  
Warm Temperature ◽  
Anaerobic Baffled Reactor ◽  
Similar Chemical ◽  
Removal Efficiencies

Abstract In this research, a hybrid anaerobic baffled reactor (HABR) configuration was proposed consisting of a front sedimentation chamber and four regular baffled chambers followed by two floated filter media chambers for the treatment of domestic wastewater. Performance comparison of uninsulated and insulated HABRs was carried out operating at warm temperature (18.6–37.6 °C) under variable HRTs (30 h and 20 h). The study suggests that almost similar chemical oxygen demand (91% vs 88%), total suspended solids (90% vs 95%), turbidity (98% vs 97%), and volatile suspended solids (90% vs 93%) removal efficiencies were obtained for uninsulated and insulated HABRs. Higher removal of total nitrogen (TN) of 41%, NH4+-N of 44%, and NO3−-N of 91% were achieved by the insulated HABR compared to TN of 37%, NH4+-N of 36%, and NO3−-N of 84% by the uninsulated HABR, whereas lower PO43− removal efficiency of 17% was found in the insulated HABR compared to 24% in the uninsulated HABR. This indicated insulation increased nitrogen removal efficiencies by 4% for TN, 8% for NH4+-N and 7% for NO3−-N, but decreased PO43−removal efficiency by 7%.

Performance evaluation of subsurface wastewater infiltration system in treating domestic sewage

2012 ◽  
Vol 65 (4) ◽  
pp. 713-720 ◽  
Author(s):  
Ying-Hua Li ◽  
Hai-Bo Li ◽  
Jing Pan ◽  
Xin Wang ◽  
Tie-Heng Sun
Keyword(s):  
Operation Mode ◽  
Oxygen Demand ◽  
Surface Water Quality ◽  
Domestic Wastewater ◽  
Ammonia Nitrogen ◽  
The Mean ◽  
Removal Efficiencies ◽  
One Year ◽  
Physical And Chemical ◽  
Over Time

This study was to investigate domestic treatment efficiency of a subsurface wastewater infiltration (SWI) system over time. The performances of a young SWI system (in Shenyang University, China, fully operated for one year) and a mature SWI system (in Shenyang Normal University, China, fully operated for seven years) under the same operation mode were contrasted through field-scale experiments for one year. The performance assessment for these systems is based on physical and chemical parameters collected. The removal efficiencies within the young system were relatively high if compared with the mature one: for biochemical oxygen demand (BOD), chemical oxygen demand (COD), suspended solids (SS), ammonia nitrogen (NH3-N) and total phosphorus (TP) were 95.0, 89.1, 98.1, 87.6 and 98.4%, respectively. However, the removal efficiencies decreased over time. The mean removal efficiencies for the mature SWI system were as follows: BOD (89.6%), COD (87.2%), SS (82.6%), NH3-N (69.1%) and TP (74.4%). The results indicate that the mature SWI system successfully removed traditional pollutants such as BOD from domestic wastewater. However, the nutrient reduction efficiencies (including NH3-N and TP) decreased after seven years of operation of the mature SWI system. Meanwhile, the SWI system did not decrease the receiving surface water quality.

The Study of Engineering Control Parameters on Soybean Protein Wastewater by UASB Reactor

2010 ◽  
Vol 113-116 ◽  
pp. 1031-1035 ◽  
Author(s):  
Yi Sun ◽  
Zi Rui Guo ◽  
Xiao Ye Liu ◽  
Yong Feng Li
Keyword(s):  
Chemical Oxygen Demand ◽  
Loading Rate ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Hydrogen Yield ◽  
Brown Sugar

In order to disscuss the ability of H2-production and wastewater treatment, a up-flow anaerobic sludge bed (UASB) using a synthesize substrate with brown sugar wastewater was conducted to investigate the hydrogen yield, hydrogen producing rate, fermentation type of biohydrogen production, and the chemical oxygen demand (COD) removal rate, respectively. In this paper, UASB reactor was seeded with sludge from the Harbin Wenchang Sewage treatment plant dewatered sludge. Successful start-up of the reactor was achieved within 40 days at 35±1°C.The concentration of chemical oxygen demand (COD) in influent is increased from 1100mg/L . When it reached maximum, the loading rate was adjusted in a small way and indicators such as VFA, pH and COD in effluent as well as gas production are observed. The most relevant parameters were calibrated with lab-scale experimental data. These experimental results clearly showed that, the most proper corresponding organic loading rate (OLR) and hydraulic retention time (HRT) were 6 kg/ (m3.d)（COD=6000mg/L）and 24 h respectively. Up to 85% of COD was removed and the CH4 production rate of 3.2 m3 / (m3 .d) was obtained. The produced biogas contained 72% of CH4. In the mean time, anaerobic sludge multiplies more faster and exiguous particles appeared. Granules with diameter 1-3mm.

Sign in / Sign up

Export Citation Format

Share Document