A GIS-based water distribution model for Zhengzhou city, China

2011 ◽  
Vol 11 (4) ◽  
pp. 497-503 ◽  
Author(s):  
Hou Yu-Kun ◽  
Zhao Chun-Hui ◽  
Huang Yu-Chung
Keyword(s):  
Water Supply ◽  
Distribution System ◽  
Water Distribution ◽  
Distribution Network ◽  
Water Distribution Network ◽  
Hydraulic Model ◽  
Distribution Model ◽  
Roughness Coefficient ◽  
Model Parameters ◽  
Pipe Roughness

Many water companies in China are developing GIS as a computer-based tool, for mapping and analyzing objects and events that happen on a water distribution network. However, only a few companies have taken a further step to develop a hydraulic model based on GIS, and Zhengzhou Water Supply Corporation is one of them. The WaterGEMS V8 XM from Bentley is used to develop the hydraulic model for the water distribution network in Zhengzhou city, which has a population of over 3 million. During establishment of the model, some of the data extracted from GIS are missing, abnormal, and redundant and require careful screening, searching, and judging. Model calibration is performed after a sensitivity analysis. Peaking factor and pipe roughness coefficient are key model parameters to calibrate. In calibrating peaking factors, the distribution system is divided into 5 operation districts with different types of water usage. To calibrate pipe roughness coefficients, the system was divided into 4 water supply districts with different attributes of pipelines. Finally, a case study of pipe layout evaluation it shows the hydraulic model to be a powerful tool for water supply management.

Determination of Neutral Point in Water Distribution Network Pipes with Variable Discharge on Route

2014 ◽  
Vol 909 ◽  
pp. 428-432 ◽  
Author(s):  
Ioan Sarbu ◽  
Gabriel Ostafe
Keyword(s):  
Water Supply ◽  
Distribution System ◽  
Water Distribution ◽  
Distribution Network ◽  
Water Distribution Network ◽  
Distribution Networks ◽  
Neutral Point ◽  
Water Supply Systems ◽  
Proposed Model

Distribution networks are an essential part of all water supply systems. Distribution system costs within any water supply scheme may be equal to or greater than 60% of the entire cost of the project. The reliability of supply is much greater in the case of looped networks. The pipe networks have concentrated outflows or uniform outflow along the length of each pipe. In some pipes with variable discharge of a looped distribution network, water velocity could be reversed between its extremities. Thus, it is a water stall point denominated neutral point in which the discharge is null. In this paper a mathematical model for the determination of water stall point location in the pipes with distributed consumption is developed. This model has been implemented in a computer program for PC microsystems. Numerical example will be presented to demonstrate the accuracy and efficiency of the proposed model.

scholarly journals Process of hydraulic models calibration

2018 ◽  
Vol 59 ◽  
pp. 00007
Author(s):  
Izabela Zimoch ◽  
Ewelina Bartkiewicz
Keyword(s):  
Water Supply ◽  
Distribution System ◽  
Water Distribution ◽  
Interdisciplinary Approach ◽  
Operating Conditions ◽  
Roughness Coefficient ◽  
Water Supply Systems ◽  
Model Parameters ◽  
Network Graph ◽  
Supply Systems

Mathematical modelling of the water supply systems (WSS) and water quality changes in the system is a complex and difficult task to solve, it requires an interdisciplinary approach to considering the determinants of WSS work. Prognosis models of the WSS in relation to hydraulic quantities are well known and there are many packages that implement these models. These packages allow you to calculate the flow and pressure in the water distribution system under certain operating conditions. However, to make a hydraulic model a useful tool in the management of water supply systems, a calibration process is required. This process involves estimating model parameters to minimize the difference between model results and actual observations. This is a complex and multi-stage process where the network graph and parameters such as roughness coefficient, pump characteristics, or nodal demands are checked and corrected. The following work contains a complex process of calibration of the actual WSS that supplies water to the customers of the selected part of the Silesian agglomeration.

scholarly journals Model Performance Indicator of Aging Pipes in a Domestic Water Supply Distribution Network

Water ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 2378 ◽  
Author(s):  
Norzaura Abd Rahman ◽  
Nur Shazwani Muhammad ◽  
Jazuri Abdullah ◽  
Wan Hanna Melini Wan Mohtar
Keyword(s):  
Water Distribution ◽  
Performance Indicator ◽  
Distribution Network ◽  
Model Performance ◽  
Water Distribution Network ◽  
Distribution Model ◽  
Coefficient Of Determination ◽  
Roughness Coefficient ◽  
Efficiency Coefficient ◽  
Domestic Water

Aging pipes in the domestic water distribution network have the potential to decrease the quality and quantity of the treated water supplied to the consumers. Therefore, a calibrated water distribution model is helpful to monitor and understand the behaviour of a real water distribution network. However, a comprehensive performance indicator and an integrated method to assess the efficiency of model performance have not been well established in the literature. This study developed a methodology for a model calibration exercise, with consideration of two uncertainty parameters, i.e., Hazen–Williams roughness coefficient of the pipes and Non-Revenue Water (NRW) in each nodal demand. Following this, a statistical color-coded performance indicator was established, based on the Nash–Sutcliffe Efficiency Coefficient (NSEC), the coefficient of determination (R2), the correlation coefficient (r), and the Mean Absolute Error (MAE). The accuracy of the calibrated model was measured by Discrepancy Ratio (DR) analysis. This study concluded that the model performed well when NRW was added to the nodal demand in zone(s) with suspected water loss activities. The suggested Hazen–Williams roughness coefficient for PVC pipes was between 130 and 140 for pipes aged more than 20 years. The threshold error value to determine the accuracy of the simulated model was proposed to be between –0.05 and 0.05.

A study on appropriate investment of pipeline rehabilitation for water distribution network

2005 ◽  
Vol 5 (2) ◽  
pp. 31-38
Author(s):  
A. Asakura ◽  
A. Koizumi ◽  
O. Odanagi ◽  
H. Watanabe ◽  
T. Inakazu
Keyword(s):  
Monte Carlo Simulation ◽  
Monte Carlo ◽  
Water Supply ◽  
Water Distribution ◽  
Ad Hoc ◽  
Distribution Network ◽  
Water Distribution Network ◽  
Distribution Networks ◽  
Optimal Basis ◽  
Model Case

In Japan most of the water distribution networks were constructed during the 1960s to 1970s. Since these pipelines were used for a long period, pipeline rehabilitation is necessary to maintain water supply. Although investment for pipeline rehabilitation has to be planned in terms of cost-effectiveness, no standard method has been established because pipelines were replaced on emergency and ad hoc basis in the past. In this paper, a method to determine the maintenance of the water supply on an optimal basis with a fixed budget for a water distribution network is proposed. Firstly, a method to quantify the benefits of pipeline rehabilitation is examined. Secondly, two models using Integer Programming and Monte Carlo simulation to maximize the benefits of pipeline rehabilitation with limited budget were considered, and they are applied to a model case and a case study. Based on these studies, it is concluded that the Monte Carlo simulation model to calculate the appropriate investment for the pipeline rehabilitation planning is both convenient and practical.

scholarly journals DEVELOPMENT OF CLEAN WATER DISTRIBUTION NETWORK SYSTEM IN GENTENG SUB-DISTRICT BANYUWANGI USING EPANET 2.0 PROGRAM

2019 ◽  
Vol 3 (2) ◽  
pp. 172
Author(s):  
Ayu Rahmad Jayanti ◽  
Ririn Endah Badriani ◽  
Yeny Dhokhikah
Keyword(s):  
Discharge Capacity ◽  
Distribution System ◽  
Water Distribution ◽  
Water Discharge ◽  
Distribution Network ◽  
Water Distribution Network ◽  
Public Works ◽  
Network System ◽  
Clean Water ◽  
Simulation Results

The clean water distribution in the Genteng Subdistrict, Banyuwangi Regency is included in the service area of the Zone 1 PDAM tile unit. The 60 liters/second reservoir discharge capacity is obtained from Sumber Umbul Sari in the Glenmore District. The distribution of clean water in Zone 1 is still less than 70% of the area served, as the installed discharge capacity is estimated to be insufficient. In order to achieve the distribution goal, a network system must be developed by adding direct debits and planning a new pipeline. The Epanet 2.0 program simplifies the calculation of pipeline networks by integrating elevation data, network maps, pipeline specification, and load. The analysis of the simulation results was conducted using the Public Works Minister's hydraulic parameter standards 2007. Planning of a distribution network and a cost budget in 2029 were done to estimate the water supply needs and budgets required. The hydraulic simulation results based on the analysis of the pressure of all joints are in accordance with the standard, while the analysis of the velocity in pipe is less standard. The need for water discharge in 2029 is 71.6 liters/second. In Kembiritan Village, the construction of distribution pipes with an additional reservoir unit was planned. The planned pipe dimensions in the development area were 25 mm at 796 meters, 50 mm at 4062 meters, and 75 mm at 1518 meters. The cost of planning a clean water distribution system in 2029 is Rp. 1,431,375,000.00. Distribusi air bersih di Kecamatan Genteng Kabupaten Banyuwangi merupakan wilayah pelayanan Zona 1 PDAM unit Genteng. Kapasitas debit reservoir sebesar 60 liter/detik berasal dari sumber umbul sari di Kecamatan Glenmore. Pendistribusian air bersih di wilayah Zona 1 masih kurang dari 70% wilayah yang terlayani, karena diperkirakan kapasitas debit yang terpasang kurang mencukupi. Untuk memenuhi target pemerataan distribusi perlu pengembangan sistem jaringan dengan penambahan debit dan perencanaan jaringan pipa baru. Program Epanet 2.0 memudahkan dalam perhitungan jaringan perpipaan dengan mengintegrasi data elevasi, peta jaringan, spesifikasi pipa dan debit. Analisis hasil simulasi menggunakan standar parameter hidrolis Permen PU 2007. Perencanaan pengembangan jaringan distribusi dan anggaran biaya pada tahun 2029 guna memperkirakan debit kebutuhan air dan anggaran biaya yang dibutuhkan. Hasil simulasi hidrolis berdasarkan analisis tekanan semua junction telah sesuai standar, sedangkan analisis kecepatan masih di bawah standar. Kebutuhan debit air tahun 2029 sebesar 71,6 Liter/detik. Pengembangan pipa distribusi direncanakan di Desa Kembiritan dengan tambahan satu unit reservoir. Dimensi pipa rencana di wilayah pengembangan digunakan diameter 25 mm sepanjang 796 m, diameter 50 mm sepanjang 4062 m dan diameter 75 mm sepanjang 1518 m. Biaya perencanaan sistem distribusi air bersih tahun 2029 sebesar Rp. 1.431.375.000,00.

scholarly journals Leakage Detection through HL in Gurthali Water Supply Distribution Network using EPANET

2020 ◽  
Vol 9 (3) ◽  
pp. 3558-3565
Keyword(s):  
Pressure Drop ◽  
Water Distribution ◽  
Distribution Network ◽  
Research Work ◽  
Water Distribution Network ◽  
Leak Detection ◽  
Head Loss ◽  
Hydraulic Model ◽  
Leakage Detection ◽  
Valve Control

Water distribution network (WDN) design of hydraulic model Gurthali, NARWANA-JIND, HARYANA and objective of this paper to detecting the leakage in it.In current research work to find out the Hl through normal valve and leak valve control setting with randomly value.To detect the Head Loss to usedDarcy Weisbach methodwhich calculate the major and minor loss with friction in pipes links. EPANET tool is used to create enlarge hydraulic model and simulate the data. All the pipes to be analysis unit head loss and nodes analysis head loss foe every houses. For leak detection, four normal valve include to compute head loss or pressure drop on nodes, pipes and leak detection valves. Also find out the pressure and head loss on the all nodes and pipes.MS Excel used for leak detection data, at the various head loss values in valves, nodes, pipes links. Plot the various graphs with head loss on valves which generated that HL reduces drastically

scholarly journals Rehabilitation Planning of Water Distribution neTwork through a Reliability – Based Risk Assessment

2017 ◽  
Author(s):  
Marianna D'Ercole ◽  
Maurizio Righetti ◽  
Gema Raspati ◽  
Paolo Bertola ◽  
Rita Maria Ugarelli
Keyword(s):  
Water Supply ◽  
Distribution System ◽  
Water Distribution ◽  
Climate Change Impacts ◽  
Water Distribution Network ◽  
Supply System ◽  
Water Supply System ◽  
Analysis Model ◽  
Output Analysis ◽  
Support Tool

The management of existing water distribution system (WDS) is challenged by ageing of infrastructure, population growth, increasing of urbanization, climate change impacts and environmental pollution. Therefore, there is a need for integrated solutions that support decision makers to plan today, while taking into account the effect of these factors in the mid and long term. The paper is part of a more comprehensive project, where advanced hydraulic analysis for WDS is coupled with a dynamic resources input-output analysis model. The proposed modeling solution can be used to optimize the performance of a water supply system while considering also the energy consumption and consequently the environmental impacts. Therefore, as a support tool in the management of a water supply system also in the intervention planning. Here a possible application is presented for rehabilitation/replacement planning while maximizing the network mechanical reliability and minimizing risk of unsupplied demand and pressure deficit, under given economic constraints.

scholarly journals Promoting equitable water distribution system from Melamchi Water Supply Project in Kathmandu Valley

2020 ◽  
Vol 20 (8) ◽  
pp. 2964-2970
Author(s):  
D. P. Ayadi ◽  
A. Rai ◽  
A. Pandey
Keyword(s):  
Water Supply ◽  
Distribution System ◽  
Water Distribution ◽  
Water Distribution System ◽  
Water Distribution Network ◽  
Supply System ◽  
Kathmandu Valley ◽  
Drinking Water Resources ◽  
Key Issues

Abstract The effective and efficient supply of drinking water resources are key to its long-term use and access. In recent decades, the population of Kathmandu Valley has exploded owing to several factors. The water supply system here has also undergone remarkable changes and efforts have been made to enhance its equitable distribution. The major effort, of course, is the Melamchi Water Supply Project (MWSP). As the project approaches completion of its first phase, we would like to point out several key issues for the water distribution system here and express our opinions on promoting equitable water distribution. For this we conducted a thorough literature review and found that improvement in the water distribution network and water tariff in the valley, along with promotion of alternative mitigation options, are the focal issues for promoting an equitable water distribution system in Kathmandu Valley.

Sign in / Sign up

Export Citation Format

Share Document