scholarly journals Unstable flow structure around partially buried objects on a simulated river bed

2016 ◽  
Vol 19 (1) ◽  
pp. 31-46 ◽  
Author(s):  
Yovanni A. Cataño-Lopera ◽  
Blake J. Landy ◽  
Marcelo H. García
Keyword(s):  
Unsteady Flow ◽  
Flow Structure ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Equation Model ◽  
Navier Stokes ◽  
Unstable Flow ◽  
Turbulent Structures ◽  
Buried Objects ◽  
River Bed

The unsteady flow characteristics around two partially buried objects, a short cylinder and a truncated cone, were examined with a three-dimensional, non-hydrostatic hydrodynamic model under similar steady unidirectional currents with flow Reynolds numbers, Re, of 86,061 and 76,209, respectively. Model simulations were conducted with the two objects partially buried in a simulated rippled river bed. A Reynolds-averaged Navier–Stokes (RANS) equation model coupled with a κ-ε turbulence closure was used to validate the experimental velocity measurements. A large eddy simulation (LES) turbulence model was subsequently used to characterize the unsteady flow structure around the objects. The LES closure allowed for the characterization of highly unsteady coherent turbulent structures such as the horse-shoe vortex, the arch-shaped vortex, as well as vortex shedding in the wake of the object.

The inlet flow structure of a conceptual open-nose supersonic drone

2021 ◽  
pp. 095441002098304
Author(s):  
Eiman B Saheby ◽  
Xing Shen ◽  
Anthony P Hays ◽  
Zhang Jun
Keyword(s):  
Flow Structure ◽  
Stokes Equations ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Computational Fluid Dynamic Simulation ◽  
Navier Stokes ◽  
Ansys Fluent ◽  
Navier Stokes Equations ◽  
Aerodynamic Efficiency ◽  
Performance Effects

This study describes the aerodynamic efficiency of a forebody–inlet configuration and computational investigation of a drone system, capable of sustainable supersonic cruising at Mach 1.60. Because the whole drone configuration is formed around the induction system and the design is highly interrelated to the flow structure of forebody and inlet efficiency, analysis of this section and understanding its flow pattern is necessary before any progress in design phases. The compression surface is designed analytically using oblique shock patterns, which results in a low drag forebody. To study the concept, two inlet–forebody geometries are considered for Computational Fluid Dynamic simulation using ANSYS Fluent code. The supersonic and subsonic performance, effects of angle of attack, sideslip, and duct geometries on the propulsive efficiency of the concept are studied by solving the three-dimensional Navier–Stokes equations in structured cell domains. Comparing the results with the available data from other sources indicates that the aerodynamic efficiency of the concept is acceptable at supersonic and transonic regimes.

Fluid Flow Structure in Arterial Bypass Anastomosis

2005 ◽  
Vol 127 (4) ◽  
pp. 611-618 ◽  
Author(s):  
C. M. Su ◽  
D. Lee ◽  
R. Tran-Son-Tay ◽  
W. Shyy
Keyword(s):  
Fluid Flow ◽  
Flow Structure ◽  
Bypass Graft ◽  
Flow Characteristics ◽  
Navier Stokes ◽  
Complex Flow ◽  
Arterial Bypass ◽  
Flow Recirculation ◽  
Area Reduction ◽  
Complex Flow Structure

The fluid flow through a stenosed artery and its bypass graft in an anastomosis can substantially influence the outcome of bypass surgery. To help improve our understanding of this and related issues, the steady Navier-Stokes flows are computed in an idealized arterial bypass system with partially occluded host artery. Both the residual flow issued from the stenosis—which is potentially important at an earlier stage after grafting—and the complex flow structure induced by the bypass graft are investigated. Seven geometric models, including symmetric and asymmetric stenoses in the host artery, and two major aspects of the bypass system, namely, the effects of area reduction and stenosis asymmetry, are considered. By analyzing the flow characteristics in these configurations, it is found that (1) substantial area reduction leads to flow recirculation in both upstream and downstream of the stenosis and in the host artery near the toe, while diminishes the recirculation zone in the bypass graft near the bifurcation junction, (2) the asymmetry and position of the stenosis can affect the location and size of these recirculation zones, and (3) the curvature of the bypass graft can modify the fluid flow structure in the entire bypass system.

A 3D Unsteady Flow Analysis in a Doubly Constricted Tube

2000 ◽  
Author(s):  
B. V. Rathish Kumar ◽  
T. Yamaguchi ◽  
H. Liu ◽  
R. Himeno
Keyword(s):  
Pressure Drop ◽  
Unsteady Flow ◽  
Stokes Equations ◽  
Vortex Formation ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
In Series ◽  
3D Unsteady Flow

Abstract Unsteady flow dynamics in a doubly constricted vessel is analyzed by using a time accurate Finite Volume solution of three dimensional incompressible Navier-Stokes equations. Computational experiments are carried out for various values of Reynolds number in order to assess the criticality of multiple mild constrictions in series and also to bring out the subtle 3D features like vortex formation. Studies reveal that pressure drop across a series of mild constrictions can get physiologically critical. Further this pressure drop is found to be sensitive to the spacing between the constrictions and also to the oscillatory nature of the inflow profile.

scholarly journals 3D Numerical Study of the Flow Properties in a Double-Spur Dikes Field during a Flood Process

Water ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1574 ◽  
Author(s):  
Xun Han ◽  
Pengzhi Lin
Keyword(s):  
Water Surface ◽  
Numerical Study ◽  
Flow Characteristics ◽  
Field Measurements ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
River Bed ◽  
Hydrodynamic Evolution ◽  
Spur Dikes ◽  
Potential Damage

A 3D numerical model is developed to study the flow characteristics of a double-spur dikes field on Yangtze River during a flood process, which was presented by the variation of the flow condition. The model is based on Navier–Stokes (NS) equations, the porous medium method (PMM) is employed to treat the solid structures including the river bed surface, the volume of fluid (VOF) method is applied to track the motion of the water surface during the flood process, and large eddy simulation (LES) is adopted to capture the turbulence transport and dissipation. Using this model, the target reach’s flow field before the construction of double-spur dikes is simulated first, while the numerical results are compared to the field measurements on flow velocity and water surface level, and fairly good agreements are shown. Then, the model is applied to reproduce the hydrodynamic evolution during a flood process after double-spur dikes’ constructions, while the detailed 3D flow fields are obtained under some certain states with different submergence rates of the spur dikes; finally, the potential damage positions around these spur dikes are analyzed accordingly.

scholarly journals Modeling the 3-d flow around a cylinder using the SAS hybrid model

2014 ◽  
Vol 16 (5) ◽  
pp. 901-918 ◽  
Keyword(s):  
Turbulence Modeling ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Cross Flow ◽  
Numerical Code ◽  
Navier Stokes ◽  
Computational Domain ◽  
Mean Flow ◽  
Unstable Flow ◽  
Vortex Size

<div> <p>Three-dimensional calculations were performed to simulate the flow around a cylindrical vegetation element using the Scale Adaptive Simulation (SAS) model; commonly, this is the first step of the modeling of the flow through multiple vegetation elements. SAS solves the Reynolds Averaged Navier-Stokes equations in stable flow regions, while in regions with unstable flow it goes unsteady producing a resolved turbulent spectrum after reducing eddy viscosity according to the locally resolved vortex size represented by the von Karman length scale. A finite volume numerical code was used for the spatial discretisation of the rectangular computational domain with stream-wise, cross-flow and vertical dimensions equal to 30D, 11D and 1D, respectively, which was resolved with unstructured grids. Calculations were compared with experiments and Large Eddy Simulations (LES). Predicted overall flow parameters and mean flow velocities exhibited a very satisfactory agreement with experiments and LES, while the agreement of predicted turbulent stresses was satisfactory. Calculations showed that SAS is an efficient and relatively fast turbulence modeling approach, especially in relevant practical problems, in which the very high accuracy that can be achieved by LES at the expense of large computational times is not required.</p> </div> <p>&nbsp;</p>

Numerical Study on Supersonic Combustor with an Allotype Cavity

2014 ◽  
Vol 694 ◽  
pp. 187-192
Author(s):  
Jin Xiang Wu ◽  
Jian Sun ◽  
Xiang Gou ◽  
Lian Sheng Liu
Keyword(s):  
Alternative Model ◽  
Numerical Study ◽  
Reverse Flow ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Experimental Result ◽  
Navier Stokes ◽  
Cold Flow ◽  
Hypersonic Inlet ◽  
Good Agreement

The three-dimensional coupled explicit Reynolds Averaged Navier–Stokes (RANS) equations and the two equation shear-stress transport k-w (SST k-w) model has been employed to numerically simulate the cold flow field in a special-shaped cavity-based supersonic combustor. In a cross-section shaped rectangular, hypersonic inlet with airflow at Mach 2.0 chamber, shock structures and flow characteristics of a herringbone-shaped boss and a herringbone-shaped cavity models were discussed, respectively. The results indicate: Firstly, according to the similarities of bevel-cutting shock characteristics between the boss case and the cavity case, the boss structure can serve as an ideal alternative model for shear-layer. Secondly, the eddies within cavity are composed of herringbone-spanwise vortexes, columnar vortices in the front and main-spanwise vortexes in the rear, featuring tilting, twisting and stretching. Thirdly, the simulated bottom-flow of cavity is in good agreement with experimental result, while the reverse flow-entrainment resulting from herringbone geometry and pressure gradient. However, the herringbone-shaped cavity has a better performance in fuel-mixing.

Three-Dimensional Numerical Prediction of the Hydrodynamic Loads and Motions of Offshore Structures

2000 ◽  
Vol 122 (4) ◽  
pp. 294-300 ◽  
Author(s):  
Karl W. Schulz ◽  
Yannis Kallinderis
Keyword(s):  
Flow Structure ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Structural Response ◽  
Offshore Structures ◽  
Three Dimensions ◽  
Navier Stokes ◽  
Hydrodynamic Loads ◽  
Drag Coefficients ◽  
Lift And Drag

A generalized numerical method for solution of the incompressible Navier-Stokes equations in three-dimensions has been developed. This solution methodology allows for the accurate prediction of the hydrodynamic loads on offshore structures, which is then combined with a rigid body structural response to address the flow-structure coupling which is often present in offshore applications. Validation results using this method are first presented for fixed structures which compare the drag coefficients of sphere and cylinder geometries to experimental measurements over a range of subcritical Reynolds numbers. Additional fixed structure results are then presented which explore the influence of aspect ratio effects on the lift and drag coefficients of a bare circular cylinder. Finally, the spanwise flow variations between a fixed and freely vibrating cylindrical structure are compared to demonstrate the ability of the flow-structure method to correctly predict correlation length increases for a vibrating structure. [S0892-7219(00)00904-3]

Flow Characteristics in a Three-Dimensional Rectangular Channel With a Pair of Ribs Placed Symmetrically at the Channel Walls

2000 ◽  
Author(s):  
M. Singh ◽  
P. K. Panigrahi ◽  
G. Biswas
Keyword(s):  
Heat Transfer ◽  
Large Scale ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Navier Stokes ◽  
Complex Flow ◽  
Energy Equations

Abstract A numerical study of rib augmented cooling of turbine blades is reported in this paper. The time-dependent velocity field around a pair of symmetrically placed ribs on the walls of a three-dimensional rectangular channel was studied by use of a modified version of Marker-And-Cell algorithm to solve the unsteady incompressible Navier-Stokes and energy equations. The flow structures are presented with the help of instantaneous velocity vector and vorticity fields, FFT and time averaged and rms values of components of velocity. The spanwise averaged Nusselt number is found to increase at the locations of reattachment. The numerical results are compared with available numerical and experimental results. The presence of ribs leads to complex flow fields with regions of flow separation before and after the ribs. Each interruption in the flow field due to the surface mounted rib enables the velocity distribution to be more homogeneous and a new boundary layer starts developing downstream of the rib. The heat transfer is primarily enhanced due to the decrease in the thermal resistance owing to the thinner boundary layers on the interrupted surfaces. Another reason for heat transfer enhancement can be attributed to the mixing induced by large-scale structures present downstream of the separation point.

Numerical Investigation of Positive Displacement Rotary Lobe Pump With Twisted Rotors

2014 ◽  
Author(s):  
Xiaojun Jiang ◽  
Yi Li ◽  
Zhaohui He ◽  
Cui Baoling ◽  
Wenlong Dong
Keyword(s):  
Flow Structure ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Dynamic Flow ◽  
Flow Fluctuation ◽  
Flow Field Characteristics ◽  
Lobe Pump ◽  
The Impact

The three-dimensional flow field characteristics are obtained by performing numerical simulation of flow in a lobe pump with twisted rotors. The relationship between the dynamic flow structure and the flow fluctuation is explored. Actually, the viscous incompressible Navier-Stokes equations are solved within an unsteady flow model. The dynamic mesh technique is applied to obtain the dynamic flow structure. By comparing the simulated results of straight rotor with those of twisted rotor, the effect of rotor shape on the flow fluctuation was revealed. Finally, the impact of the lobes number of rotors on flow pulsations is discussed. The results show that there is an intrinsic relationship between the flow fluctuation and the vortex in the lobe pump. The use of twisted rotors can effectively improve the internal flow characteristics of lobe pump and reduce flow fluctuation. With the increase of the number of lobes, the lobe pump output is more stable and capacity has been improved.

Unsteady Flow at the Outlet of the High Specific Speed Centrifugal Compressor Impeller

1984 ◽  
Author(s):  
Fumikata Kano ◽  
Takafumi Shirakami
Keyword(s):  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Coal Gasification ◽  
Three Dimensional ◽  
Axial Direction ◽  
Navier Stokes ◽  
Meridional Plane ◽  
Mixed Flow ◽  
Navier Stokes Equation ◽  
Specific Speed

The unsteady flow at the outlet of the high specific speed mixed flow Impeller was studied. The specific speed is 500 (m3/min)1/2 · rpm · m−3/4. The flow is strongly influenced by the impeller blading. The other hand, the flow influences the performance of the stationary vanes downstream of the impeller. The flow path at the outlet of the mixed flow impeller is inclined to the axial direction and is curved in the meridional plane. The study was carried out to develop the 30 MW centrifugal compressor. This compressor is used in the field of the coal gasification, the geothermal power generation, etc. The distributions of flow velocity, pressure and temperature of three dimensional flow were measured using a high sensitive pressure transducer and a total temperature probe. The flow was surveyed across the entire passage at about ten axial locations including endwall boundary layer. A theoretical analysis was also carried out using the linearized Navier-Stokes equation.

Sign in / Sign up

Export Citation Format

Share Document