scholarly journals The CFD analysis of influence the start of fuel injection (SOI) on combustion parameters and exhaust gas composition of the marine 4-stroke engine

2019 ◽  
Vol 177 (2) ◽  
pp. 40-45
Author(s):  
Jerzy KOWALSKI
Keyword(s):  
Fuel Injection ◽  
Combustion Process ◽  
Three Dimensional ◽  
Injection Timing ◽  
Zone Model ◽  
Exhaust Gas ◽  
Nitric Oxides ◽  
Injection Angle ◽  
The Impact ◽  
Stroke Engine

The paper presents a theoretical analysis of the impact of injection timing on the parameters of the combustion process and the com-position of exhaust gas from a 4-stroke engine designed to shipbuilding. The analysis was carried out based on a three-dimensional multi-zone model of the combustion process. This model has been prepared on the basis of properties of the research facility. The input data to the model were obtained through laboratory tests. Results of calculations showed that the change of the start of injection angle (SOI) from the value of 14 degrees before TDC to 22 degrees before TDC results in changes in the combustion rate and thus an increase in the temperature of the combustion process as well as the increase of nitric oxides fraction in the exhaust gas. Simultaneously the maximum combustion pressure increases also.

scholarly journals PM and NOX emissions amelioration from the combustion of diesel/ethanol-methanol blends applying exhaust gas recirculation (EGR)

2022 ◽  
Vol 961 (1) ◽  
pp. 012044
Author(s):  
Miqdam T. Chaichan ◽  
Noora S. Ekab ◽  
Mohammed A. Fayad ◽  
Hayder A. Dhahad
Keyword(s):  
Equivalence Ratio ◽  
Fuel Injection ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Operating Parameters ◽  
Injection Timing ◽  
Exhaust Gas ◽  
Oxygenated Fuel ◽  
Oxygenated Fuels ◽  
Gas Recirculation

Abstract The fuel injection timings, equivalence ratio (Ø) and exhaust gas recirculation are considered the most important parameters can effect on combustion process and lower exhaust emissions concentrations. The influence of 15% EGR technology and operating parameters (Ø and injection timing) on NOX emissions and particulate matter (PM) using oxygenated fuel (ethanol and methanol) blends were investigated in this experimental study. The results showed that the NOX emissions concentrations with increasing the equivalence ratio (Ø) and applied EGR for all fuels studied. Besides, the E10 and M10 decreased the PM concentrations compared to the diesel fuel under various equivalence ratios (Ø). The applied EGR increased the PM concentrations, but when combination of oxygenated fuels and EGR leading to the decrease in the PM formation. The NOX emissions concentrations decreased from the combined effect of EGR and oxygenated fuels by 16.8%, 22.91% and 29.5% from the combustion of diesel, M10 and E10, respectively, under various injection timings. It is indicated that NOX emissions decreased with retarded injection timings, while the PM decreased under advanced injection timings.

scholarly journals Investigation into the effect of different fuels on ignition delay of M-type diesel combustion process

2008 ◽  
Vol 12 (1) ◽  
pp. 103-114 ◽  
Author(s):  
Dzevad Bibic ◽  
Ivan Filipovic ◽  
Ales Hribernik ◽  
Boran Pikula
Keyword(s):  
Diesel Engine ◽  
Ignition Delay ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection System ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Injection Angle ◽  
Start Of Injection

An ignition delay is a very complex process which depends on a great number of parameters. In practice, definition of the ignition delay is based on the use of correlation expressions. However, the correlation expressions have very often limited application field. This paper presents a new correlation which has been developed during the research project on the direct injection M-type diesel engine using both the diesel and biodiesel fuel, as well as different values of a static injection timing. A dynamic start of injection, as well as the ignition delay, is defined in two ways. The first approach is based on measurement of a needle lift, while the second is based on measurement of a fuel pressure before the injector. The latter approach requires calculation of pressure signals delay through the fuel injection system and the variation of a static advance injection angle changing. The start of a combustion and the end of the ignition delay is defined on the basis of measurements of an in-cylinder pressure and its point of separation from a skip-fire pressure trace. The developed correlation gives better prediction of the ignition delay definition for the M-type direct injection diesel engine in the case of diesel and biodiesel fuel use when compared with the classic expression by the other authors available in the literature.

scholarly journals The model of combustion process in the marine 4-stroke engine for exhaust gas composition assessment

2016 ◽  
Vol 165 (2) ◽  
pp. 60-69
Author(s):  
Jerzy KOWALSKI
Keyword(s):  
Fuel Injection ◽  
Combustion Process ◽  
Exhaust Gas ◽  
Gas Composition ◽  
Nitric Oxides ◽  
Turbulence Flow ◽  
Direct Measurements ◽  
Carbon Compounds ◽  
Calculation Results ◽  
D Model

The paper presents the model of combustion process in the marine, turbocharged, 4-stroke and Diesel engine. The main target of modeling is the assessment of the exhaust gas composition. Presented multi-zone, 3-D model of combustion process consists of the following sub-models of processes: the fuel injection, the brake-up and the evaporation of fuel and the turbulence flow and the heat transfer phenomena. Presented model basis on the 3Z-ECFM mechanism of combustion and the initial and boundary conditions collected during direct measurements. The positive validation of the calculation results are obtained for mean and maximum value of the combustion pressure and values of oxygen and nitric oxides fractions in the exhaust gas. Unfortunately, fractions of carbon compounds in the exhaust gas are not properly calculated.

Diesel engine performance mapping using a parametrized mixing time model

2017 ◽  
Vol 19 (2) ◽  
pp. 202-213 ◽  
Author(s):  
Michal Pasternak ◽  
Fabian Mauss ◽  
Christian Klauer ◽  
Andrea Matrisciano
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Mixing Time ◽  
Combustion Process ◽  
Engine Performance ◽  
Injection Timing ◽  
Engine Control ◽  
Reactor Model ◽  
Time Model ◽  
Tabulated Chemistry

A numerical platform is presented for diesel engine performance mapping. The platform employs a zero-dimensional stochastic reactor model for the simulation of engine in-cylinder processes. n-Heptane is used as diesel surrogate for the modeling of fuel oxidation and emission formation. The overall simulation process is carried out in an automated manner using a genetic algorithm. The probability density function formulation of the stochastic reactor model enables an insight into the locality of turbulence–chemistry interactions that characterize the combustion process in diesel engines. The interactions are accounted for by the modeling of representative mixing time. The mixing time is parametrized with known engine operating parameters such as load, speed and fuel injection strategy. The detailed chemistry consideration and mixing time parametrization enable the extrapolation of engine performance parameters beyond the operating points used for model training. The results show that the model responds correctly to the changes of engine control parameters such as fuel injection timing and exhaust gas recirculation rate. It is demonstrated that the method developed can be applied to the prediction of engine load–speed maps for exhaust NOx, indicated mean effective pressure and fuel consumption. The maps can be derived from the limited experimental data available for model calibration. Significant speedup of the simulations process can be achieved using tabulated chemistry. Overall, the method presented can be considered as a bridge between the experimental works and the development of mean value engine models for engine control applications.

Reduction of Fuel Utilization Through Oxygen-Enriched Combustion in a Reheat Furnace Pusher-Type

2021 ◽  
Author(s):  
Francisco J. Martinez Zambrano ◽  
Armin K. Silaen ◽  
Kelly Tian ◽  
Joe Maiolo ◽  
Chenn Zhou
Keyword(s):  
Heat Flux ◽  
Fuel Injection ◽  
Combustion Process ◽  
Oxygen Enrichment ◽  
Rolling Temperature ◽  
Heating Zone ◽  
Reheat Furnace ◽  
Steel Slabs ◽  
The Impact ◽  
Reheating Process

Abstract Steelmaking is an energy-intensive process. Thus, energy efficiency is highly important. Several stages of steelmaking involve combustion processes. One of the most energy-consuming processes in steelmaking is the slab reheating process in a reheat furnace (RF). The energy released by fuel combustion is used to heat steel slabs to their proper hot-rolling temperature. The steel slabs move through the reheat furnace passing the three stages of heating called: Preheating Zone (PZ), Heating Zone (HZ), and Soaking Zone (SZ) to finally leave the discharge door at a rolling temperature of 2375 °F. One way to improve a reheat furnace’s fuel consumption is by implementing oxygen-enriched combustion. This study investigates the implementation of oxygen-enriched combustion in a pusher-type reheat furnace. The increment of oxygen in the combustion process allows for increasing the furnace gas temperature. Consequently, the oxygen enrichment approach allows for the reduction of fuel injection. The principal goal of this investigation is to model the combustion-based on oxygen-enrichment and develop parametric studies of fuel injection rates. The different simulations aim to match the slab heat flux profile of the industrial reheat furnace pusher-type. Computational fluid dynamics are used to generate the slab heat flux distribution. To reach more uniform slab heating, oxygen and fuel ports were alternated. Also, injection angles were modified to optimize slab heating and avoid the impact of hot spots. Thermocouple readings of the industrial reheat furnace are compared to simulation results. The results determined that 40–45% fuel reduction can be achieved.

scholarly journals Thermodynamic cycles variability of TJI gas engine with different mixture preparation systems

2020 ◽  
Vol 181 (2) ◽  
pp. 46-52
Author(s):  
Filip SZWAJCA ◽  
Krzysztof WISŁOCKI
Keyword(s):  
Fuel Injection ◽  
Combustion Process ◽  
Engine Operation ◽  
Gas Engine ◽  
Part Load ◽  
Mixture Preparation ◽  
Key Factor ◽  
Test Engine ◽  
Operation Stability ◽  
The Impact

Gas engines are a viable source of propulsion due to the ecological indicators of gas fuels and the large amount of the needed natural resources. Combustion of lean homogeneous gas mixtures allows achieving higher thermal efficiency values, which is a key factor in current engine development trends. Using the spark-jet ignition system (also called as Turbulent Jet Ignition or Two-stage combustion) significantly improves the efficiency and stability of the combustion process, especially in the part-load operation on lean or very lean mixtures. This paper presents the impact of using two different fuel injection methods: Port Fuel Injection or Mixer on the operation stability of a gas engine designed for LDVs. Comparative studies of two different mixture preparation systems were carried out on a single-cylinder AVL 5804 test engine. By re-cording the cylinder pressure for a significant number of engine cycles, it became possible to determine the repeatability of engine operation and to correlate the results with the mixture formation system and the air-fuel ratio. In the performed research the beneficial effect of the mixer system application on the engine operation stability in the part-load conditions was found.

scholarly journals Q-Learning Neural Controller for Steam Generator Station in Micro Cogeneration Systems

Energies ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5334
Author(s):  
Krzysztof Lalik ◽  
Mateusz Kozek ◽  
Szymon Podlasek ◽  
Rafał Figaj ◽  
Paweł Gut
Keyword(s):  
Numerical Model ◽  
Control Systems ◽  
Steam Generator ◽  
Full Range ◽  
Combustion Process ◽  
Liquid Fuels ◽  
Control Algorithms ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
The Impact

This article presents the results of the optimization of steam generator control systems powered by mixtures of liquid fuels containing biofuels. The numerical model was based on the results of experimental research of steam generator operation in an open system. The numerical model is used to build control algorithms that improve performance, increase efficiency, reduce fuel consumption and increase safety in the full range of operation of the steam generator and the cogeneration system of which it is a component. In this research, the following parameters were monitored: temperature and pressure of the circulating medium, exhaust gas temperature, oxygen content in exhaust gas, percentage control of oil burner power. Two methods of controlling the steam generator were proposed: the classic one, using the PID regulator, and the advanced one, using artificial neural networks. The work shows how the model is adapted to the real system and the impact of the control algorithms on the efficiency of the combustion process. The example is considered for the implementation of advanced control systems in micro-, small- and medium-power cogeneration and trigeneration systems in order to improve their final efficiency and increase the profitability of implementation.

Sign in / Sign up

Export Citation Format

Share Document