scholarly journals Determining the environmental indicators for vehicles of different categories in relation to CO2 emission based on road tests

2017 ◽  
Vol 170 (3) ◽  
pp. 66-72
Author(s):  
Jerzy MERKISZ ◽  
Łukasz RYMANIAK
Keyword(s):  
Co2 Emissions ◽  
Operating Time ◽  
Environmental Indicators ◽  
Operating Conditions ◽  
Si Engine ◽  
Propulsion Systems ◽  
System A ◽  
In Series ◽  
Series Configuration ◽  
Ci Engine

The article discusses the possibility of determining the environmental indicators for vehicles of different categories in relation to CO2 emissions. These are called toxicity indicators because they concern the compounds: CO, THC and NOx. Three Euro V compliant vehicles with different propulsion systems types were used for the study: a 0.9 dm3 urban passenger car with a SI engine and a start-stop system, a 2.5 dm3 off-road vehicle with a CI engine, and a city bus with a hybrid drive system in series configuration and a CI engine with a displacement of 6.7 dm3. Measurements were made in actual operating conditions in the Poznan agglomeration using a portable emissions measurement system (PEMS). The paper presents the characteristics of the operating time shares of vehicles and propulsion systems as well as CO2 emissions depending on the engine load and crankshaft rotational speed for individual vehicles. The determined toxicity indicators allowed to indicate their usefulness, to make comparisons between tested vehicles, and to identify directions for further work on the application and interpretation of these indicators.

scholarly journals A Reliability Model for a Two Dissimilar Units Series System with Repair Time-Dependent Standby

2020 ◽  
Vol 9 (3) ◽  
pp. 2890-2893
Keyword(s):  
Aluminum Industry ◽  
Repair Time ◽  
Reliability Model ◽  
System Optimum ◽  
System A ◽  
Regenerative Point ◽  
In Series ◽  
Series Configuration ◽  
Configuration System ◽  
Regenerative Point Technique

The present paper stochastically analyze a system comprising two dissimilar units (unit-1/unit-2) working in series configuration. System fails completely when either of the units gets failed. The repair time of unit-2 is considered to be much more as compared to the repair time of unit-1. So, to minimize the breakdown period of the system, a standby unit is provided against the second unit. Regenerative point technique (RPT) is used to develop a semi-markovian reliability model for the mentioned system. Optimum cut-off points concerning the profitability of the system have also been obtained. The model has applications in industries, particularly in aluminum industry.

scholarly journals Optimization of the Emissions Profile of a Marine Propulsion System Using a Shaft Generator with Optimum Tracking-Based Control Scheme

2020 ◽  
Vol 8 (3) ◽  
pp. 221 ◽  
Author(s):  
Joel R. Perez ◽  
Carlos A. Reusser
Keyword(s):  
Energy Efficiency ◽  
Co2 Emissions ◽  
Fuel Efficiency ◽  
Propulsion System ◽  
Operating Conditions ◽  
Propulsion Systems ◽  
Marine Propulsion ◽  
Diesel Cycle ◽  
Energy Efficiency Design Index ◽  
Carbon Dioxide Co2

Nowadays, marine propulsion systems based on thermal machines that operate under the diesel cycle have positioned themselves as one of the main options for this type of applications. The main comparative advantages of diesel engines, compared to other propulsion systems based on thermal cycle engines, are the low specific fuel consumption of residual fuels, and their higher thermal efficiency. However, its main disadvantage lies in the emissions produced by the combustion of the residual fuels, such as carbon dioxide (CO2), sulfur oxide (SOx), and nitrogen oxide (NOx). These emissions are directly related to the operating conditions of the propulsion system. Over the last decade, the International Maritime Organization (IMO) has adopted a series of regulations to reduce CO2 emissions based on the introduction of an Energy Efficiency Design Index (EEDI) and an Energy Efficiency Operational Indicator (EEOI). In this context, adding a Shaft Generator (SG) to the propulsion system favoring lower EEDI and EEOI values. The present work proposes a selective control system and optimization scheme that allows operating the shaft generator in Power Take Off (PTO) or Power Take In (PTI) mode, ensuring that the main engine operates, always, at the optimum fuel efficiency point, thus ensuring minimum CO2 emissions.

scholarly journals Optimal Calibration Strategy of a Hybrid Electric Vehicle Equipped with an Ultra-Lean Pre-Chamber SI Engine for the Minimization of CO2 and Pollutant Emissions

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 4008
Author(s):  
Fabio Bozza ◽  
Vincenzo De Bellis ◽  
Enrica Malfi ◽  
Luigi Teodosio ◽  
Daniela Tufano
Keyword(s):  
Co2 Emissions ◽  
Hybrid Electric Vehicle ◽  
Electric Energy ◽  
Pollutant Emissions ◽  
Si Engine ◽  
Engine Calibration ◽  
Driving Cycles ◽  
In Series ◽  
1D Model ◽  
Variable Valve

The complexity of modern hybrid powertrains poses new challenges for the optimal control concerning, on one hand, the thermal engine to maximize its efficiency, and, on the other hand, the vehicle to minimize the noxious emissions and CO2. In this context, the engine calibration has to be conducted by considering simultaneously the powertrain management, the vehicle characteristics, and the driving mission. In this work, a calibration methodology for a two-stage boosted ultra-lean pre-chamber spark ignition (SI) engine is proposed, aiming at minimizing its CO2 and pollutant emissions. The engine features a flexible variable valve timing (VVT) control of the valves and an E-compressor, coupled in series to a turbocharger, to guarantee an adequate boost level needed for ultra-lean operation. The engine is simulated in a refined 1D model. A simplified methodology, based on a network of proportional integral derivative (PID) controllers, is presented for the calibration over the whole operating domain. Two calibration variants are proposed and compared, characterized by different fuel and electric consumptions: the first one aims to exclusively maximize the brake thermal efficiency, and the second one additionally considers the electric energy absorbed by the E-compressor and drained from the battery. After a verification against the outcomes of an automatic optimizer, the calibration strategies are assessed based on pollutant and CO2 emissions along representative driving cycles by vehicle simulations. The results highlight slightly lower CO2 emissions with the calibration approach that minimizes the E-compressor consumption, thus revealing the importance of considering the engine calibration phase, the powertrain management, the vehicle characteristics, and its mission.

Viability of turbine blade material with a long service life

2019 ◽  
pp. 28-35
Author(s):  
O. B. Berdnik ◽  
I. N. Tsareva ◽  
M. K. Chegurov
Keyword(s):  
Heat Treatment ◽  
Service Life ◽  
Yield Strength ◽  
Mechanical Characteristics ◽  
Operating Time ◽  
Structural Features ◽  
Operating Conditions ◽  
Standard Methods ◽  
Experimental Values ◽  
Plasticity Coefficient

This article deals with structural features and characteristic changes that affect the mechanical characteristics after different service life in real conditions using the example of the blades of the 4th stage of turbine GTE-45-3 with an operating time of 13,000 to 100,000 hours. To study the change in the state of the material under different operating conditions, determine the degree of influence of heat treatment on the regeneration of the microstructure, and restore the mechanical characteristics of the alloy after different periods of operation, non-standard methods were used: relaxation tests on miniature samples to determine the physical yield strength and microplasticity limit and quantitative evaluation of the plasticity coefficient of the material from experimental values of hardness, which allow us to identify the changes occurring in the microvolumes of the material and predict the performance of the product as a whole.

scholarly journals Evaporator Optimization of Refrigerator Systems Using Quality Analysis

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 555
Author(s):  
Sangkyung Na ◽  
Sanghun Song ◽  
Seunghyuk Lee ◽  
Jehwan Lee ◽  
Hyun Kim ◽  
...  
Keyword(s):  
Power Consumption ◽  
Operating Time ◽  
Cooling Capacity ◽  
Operating Conditions ◽  
Quality Analysis ◽  
Lubricating Oil ◽  
Optimal Operating ◽  
Compressor Piston ◽  
Refrigerator Temperature ◽  
Visualization Experiments

In this study, evaporator optimization, via both experimental and simulation methods was conducted. To evaluate the evaporator performance, under the optimal system, the compressor operating time and the effects of oil on the refrigerator system were studied. If the temperature of the refrigerator chamber reaches the setting value, the compressor stops working and it leads to the temperature of the refrigerator chamber slowly increasing, due to the heat transfer to the ambient. When the refrigerator temperature is out of the setting range, the compressor works again, and the refrigerator repeats this process until the end of its life. These on/off period can be controlled through the compressor piston movement. To determine the optimal compressor operating conditions, experiments of monthly power consumption were conducted under various compressor working times and the lowest power consumption conditions was determined when the compressor worked continuously. Lubricating oil, the refrigerator system, using oil, also influenced the system performance. To evaluate the effect of oil, oil eliminated and oil systems were compared based on cooling capacity and power consumption. The cooling capacity of the oil eliminated system was 2.6% higher and the power consumption was 3.6% lower than that of the oil system. After determining the optimal operating conditions of the refrigerator system, visualization experiments and simulations were conducted to decide the optimal evaporator and the conventional evaporator size can be reduced by approximately 2.9%.

scholarly journals A Novel Hybrid LDC Converter Topology for the Integrated On-Board Charger of Electric Vehicles

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3603
Author(s):  
Vu-Hai Nam ◽  
Duong-Van Tinh ◽  
Woojin Choi
Keyword(s):  
Low Voltage ◽  
Operating Conditions ◽  
Maximum Efficiency ◽  
Battery Charger ◽  
Forward Converter ◽  
Vehicle To Grid ◽  
Circulating Current ◽  
In Series ◽  
Converter Topology ◽  
Output Capacitor

Recently, the integrated On-Board Charger (OBC) combining an OBC converter with a Low-Voltage DC/DC Converter (LDC) has been considered to reduce the size, weight and cost of DC-DC converters in the EV system. This paper proposes a new integrated OBC converter with V2G (Vehicle-to-Grid) and auxiliary battery charge functions. In the proposed integrated OBC converter, the OBC converter is composed of a bidirectional full-bridge converter with an active clamp circuit and a hybrid LDC converter with a Phase-Shift Full-Bridge (PSFB) converter and a forward converter. ZVS for all primary switches and nearly ZCS for the lagging switches can be achieved for all the operating conditions. In the secondary side of the proposed LDC converter, an additional circuit composed of a capacitor and two diodes is employed to clamp the oscillation voltage across rectifier diodes and to eliminate the circulating current. Since the output capacitor of the forward converter is connected in series with the output capacitor of the auxiliary battery charger, the energy from the propulsion battery can be delivered to the auxiliary battery during the freewheeling interval and it helps reduce the current ripple of the output inductor, leading to a smaller volume of the output inductor. A 1 kW prototype converter is implemented to verify the performance of the proposed topology. The maximum efficiency of the proposed converter achieved by the experiments is 96%.

scholarly journals Impact of Operating Time on Selected Tribological Properties of the Friction Material in the Brake Pads of Passenger Cars

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 884
Author(s):  
Andrzej Borawski
Keyword(s):  
Tribological Properties ◽  
Operating Time ◽  
Friction Material ◽  
Operating Conditions ◽  
Direct Impact ◽  
Passenger Cars ◽  
Wear Factor ◽  
Brake Pads ◽  
Road Users ◽  
The Coefficient Of Friction

Braking systems have a direct impact on the safety of road users. That is why it is crucial that the performance of brakes be dependable and faultless. Unfortunately, the operating conditions of brakes during their operating time are affected by many variables, which results in changes in their tribological properties. This article presents an attempt to develop a methodology for studying how the operating time affects the value of the coefficient of friction and the abrasive wear factor. The Taguchi method of process optimization was used to plan the experiment, which was based on tests using the ball-cratering method. The results clearly show that the degree of wear affects the properties of the friction material used in the production process of brakes.

Poly Silk Peptide Film PH Sensor Based on Zero Current Potentiometry

2012 ◽  
Vol 450-451 ◽  
pp. 554-556
Author(s):  
Ming Ming Ma ◽  
Zhi Tong ◽  
Yong Wen
Keyword(s):  
Graphite Electrode ◽  
Ph Sensor ◽  
Reference Electrode ◽  
Pencil Graphite Electrode ◽  
Solution Ph ◽  
Counter Electrodes ◽  
System A ◽  
Zero Current ◽  
In Series ◽  
Silk Peptide

A poly silk peptide film pH sensor has been developed using zero current potentiometry system. A poly silk peptide film coated pencil graphite electrode is connected in series between the working and counter electrodes of a potentiostat, and immersed in solution together with a reference electrode. When the solution pH varies, the resulting zero current potentiometry is linear with the values of the solution pH in the range of 1.81 to 11.58. This pH sensor shows high stability, accuracy, selectivity and reproduction.

Direct Outer Ring Cooling of a High Speed Jet Engine Mainshaft Ball Bearing: Experimental Investigation Results

2010 ◽  
Author(s):  
Peter Gloeckner ◽  
Klaus Dullenkopf ◽  
Michael Flouros
Keyword(s):  
Power Dissipation ◽  
High Speed ◽  
Ball Bearing ◽  
Operating Conditions ◽  
Outer Ring ◽  
Outer Diameter ◽  
Propulsion Systems ◽  
Jet Engine ◽  
Power Loss Reduction ◽  
The Impact

Operating conditions in high speed mainshaft ball bearings applied in new aircraft propulsion systems require enhanced bearing designs and materials. Rotational speeds, loads, demands on higher thrust capability, and reliability have increased continuously over the last years. A consequence of these increasing operating conditions are increased bearing temperatures. A state of the art jet engine high speed ball bearing has been modified with an oil channel in the outer diameter of the bearing. This oil channel provides direct cooling of the outer ring. Rig testing under typical flight conditions has been performed to investigate the cooling efficiency of the outer ring oil channel. In this paper the experimental results including bearing temperature distribution, power dissipation, bearing oil pumping and the impact on oil mass and parasitic power loss reduction are presented.

scholarly journals Test Results of a Polymer Radiator of MTZ-80 Tractor Cooling System

2020 ◽  
Vol 14 (1) ◽  
pp. 55-60
Author(s):  
O. N. Didmanidze ◽  
R. T. Khakimov ◽  
E. P. Parlyuk ◽  
N. A. Bol’shakov
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Cooling System ◽  
Operating Mode ◽  
Aerodynamic Characteristics ◽  
Operating Conditions ◽  
Hydrodynamic Resistance ◽  
Measuring Instruments ◽  
Research Areas ◽  
In Series

Global car manufacturers wish to increase the number of manufactured products, reduce their cost and labor input. The choice of research areas, design and technological developments in radiator construction is an extremely important and urgent task, due to the mass production of radiators for tractors and automobiles on the one hand, and the favorable development prospects of these interrelated industries, on the other. (Research purpose) To substantiate theoretically and experimentally the use of a combined cooling system containing both aluminum and polymeric water radiators and similarly liquid-oil heat exchangers based on the four principles listed above on automobiles and tractors. (Materials and methods) The authors performed bench tests using a special wind tunnel to study the thermal and aerodynamic characteristics of a prototype tractor radiator with a polyurethane core. After reaching the steady-state operating mode of the installation, the experimental values were determined for the control and measuring instruments. (Results and discussion) The authors carried out measurements of all parameters of both coolants in series at each steady-state operating mode of the bench. They obtained the main indicators dependences (reduced heat transfer, aerodynamic and hydraulic drag) of the heat exchanger, close to the operating conditions of the vehicles. (Conclusions) A prototype MTZ-80 radiator with a polyurethane core has great prospects as a future alternative radiator. An increase by 10-15 percent in the radiator heat transfer is possible by using aluminum fi ns on the surface of the polyurethane plate. A 15-20 percent reduction in hydrodynamic resistance is achieved by increasing the diameter of the capillary throughput in a polyurethane plate and the number of plates themselves in the radiator cell.

Sign in / Sign up

Export Citation Format

Share Document