scholarly journals Effect of Ultrafine Ground Granulated Blast-Furnace Slag (UFGGBFS) and Copper Slag on Ambient Cured Geopolymer Concrete

2019 ◽  
Vol 43 (6) ◽  
pp. 377-382 ◽  
Author(s):  
Vijayasarathy Rathanasalam ◽  
Jayabalan Perumalsami ◽  
Karthikeyan Jayakumar
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Copper Slag ◽  
Geopolymer Concrete ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

scholarly journals Characteristics of Blended Geopolymer Concrete Using Ultrafine Ground Granulated Blast Furnace Slag and Copper Slag

2020 ◽  
Vol 44 (6) ◽  
pp. 433-439
Author(s):  
Vijayasarathy Rathanasalam ◽  
Jayabalan Perumalsami ◽  
Karthikeyan Jayakumar
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Blast Furnace Slag ◽  
Copper Slag ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
Strength Performance ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper presents the properties of blended geopolymer concrete manufactured using fly ash and ultrafine Ground Granulated Blast Furnace Slag (UFGGBFS), along with the copper slag (CPS) as replacement of fine aggregate (crushed stone sand). Various parameters considered in this study include different sodium hydroxide concentrations (10M, 12M and 14M); 0.35 as alkaline liquid to binder ratio; 2.5 as sodium silicate to sodium hydroxide ratio and cured in ambient curing condition. Further, geopolymer concrete was manufactured using fly ash as the prime source material which is replaced with UFGGBFS (0%, 5%, 10% and 15%). Copper slag has been used as replacement of fine aggregate in this study. Properties of the fresh manufactured geopolymer concrete were studied by slump test. Compressive strength of the manufactured geopolymer concrete was tested and recorded after curing for 3, 7 and 28 days. Microstructure Characterization of Geopolymer concrete specimens was done by Scanning Electron Microscope (SEM) analysis. Experimental results revealed that the addition of UFGGBFS resulted in an increased strength performance of geopolymer concrete. Also, this study demonstrated that the strength of geopolymer concrete increased with an increase in sodium hydroxide concentration. SEM results revealed that the addition of UFGGBFS resulted in a dense structure.

scholarly journals Effect of Na2SiO3/Naoh on the Compressive Strength of Inorganic Polymer Concrete Mixed with Ground Granulated Blast Furnace Slag (GGBS) At Ambient Condition

2019 ◽  
Vol 9 (2) ◽  
pp. 1222-1228
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Ambient Condition ◽  
Polymer Concrete ◽  
Geopolymer Concrete ◽  
Split Tensile Strength ◽  
Standard Size ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper aims to investigate the influence of alkaline activators solution i.e, Na2SiO3 / NaOH on compressive strength of geopolymer concrete mixed with Ground Granulated Blast furnace slag (GGBS) for constant molarity 8 M. The ratio of alkali to binder ratio is taken as 0.5 and the ratio of Na2SiO3 / NaOH is 2.5. The geopolymer mix is based on pervious sutdies. As per Indian standard size moulds for the cube, cylinder and prism are cast, cured and tested.The specimens were tested for fresh concrete properties such as slump cone test and hardened properties such as compressive strength for cubes, split tensile strength for cylinders and flexural strength for prism different days of curing under ambient temperature. Also, a microstructural study is done by using Scanning electron microscopy (SEM), Energy dispersive X-ray (EDX) for the tested sample. It is found from the test results that, with the aid of alumino-silicate solution, early strength is achieved by geopolymer concrete within 7 days under ambient condition due to the presence of ground granulated slag.

scholarly journals Mechanical Behavior of Double Skinned Composite Hollow Columns using Geopolymer Concrete

2020 ◽  
Vol 8 (5) ◽  
pp. 4691-4696
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Steel Tube ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
Ambient Temperatures ◽  
Granulated Blast Furnace Slag ◽  
Heat Curing ◽  
Furnace Slag

This paper comprises of the experimental study of double skinned (DSCFT) Composite hollow columns using Geopolymer concrete. The diameter-thickness (D/t) ratio and the hollowness ratio were consideredas main parameters in designing the specimens. The Geopolymer Concrete used in this project is the most promising technique. It is composed of fly-ash, fine aggregate, coarse aggregate and alkaline solution. By using large volume of ordinary Portland cement (OPC) concrete, the production of cement increases 3% annually. The production of one ton of cement directly liberates about 1 ton of CO2 and indirectly liberates 0.4 ton of CO2 to atmosphere. Among the greenhouse gases, CO2 contributes about 67% of global warming. In this respect fly ash based geopolymer mortar is highly considerable. But most of the previous works on fly ash-based geopolymers concrete reveals that hardening is due to heat curing, which is considered as a limitation for cast in situ applications at low ambient temperatures. In order to overcome this situation, replacing the Ground blast furnace slag with fly ash for various proportions to achieve geopolymer concrete suitable for curing without elevated heat. The Scope of this project is to find optimization level of Ground Granulated blast furnace slag in geopolymer concrete for curing in ambient condition and to analyze the compressive Strength of optimized GGBS based Geopolymer Concrete filled double skinned steel tube by varying the size of the steel tubes.

Effect of alkali activator dosage on compressive and tensile strength of ground granulated blast furnace slag based geopolymer concrete

2021 ◽  
Author(s):  
Ashita Singh ◽  
Sudhir Singh Bhadauria ◽  
Manish Mudgal ◽  
Suresh Singh Kushwah
Keyword(s):  
Tensile Strength ◽  
Blast Furnace ◽  
Sodium Hydroxide ◽  
Blast Furnace Slag ◽  
Sodium Metasilicate ◽  
Geopolymer Concrete ◽  
Split Tensile Strength ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag ◽  
Geopolymer Binder

Use of Ordinary Portland cement contributes to environmental deterioration by releasing enormous quantity of CO2.To reduce use of cement, this research focuses on preparation of solely ground granulated blast furnace slag based geopolymer binder, activated by a combination of sodium hydroxide and sodium metasilicate cured under ambient temperature at 27°C. Engineering properties of geopolymer binder are evaluated and compared with conventional cement to assess its suitability as a binder for making geopolymer concrete. Compressive strength, flexure strength and split tensile strength are determined for geopolymer concrete. Microstructural analysis of geopolymer is performed by XRD, FTIR, FESEM and EDAX tests. The concentration of alkali activators is optimized by trials in laboratory and maximum compressive, flexural and split tensile strength of 44.07 MPa, 5.60 MPa and 4.39 MPa respectively, is obtained for geopolymer concrete at 2M concentration of sodium hydroxide solution with ratio of sodium metasilicate to sodium hydroxide taken as 2.0

scholarly journals Domınance of materıal composıtıon on mechanıcal propertıes of normal and hıgh strength grade bınary blended geopolymer concrete

2020 ◽  
Vol 2 (3) ◽  
pp. 128-133
Author(s):  
Addepalli Mallinadh Kashyap ◽  
Tanimki Chandra Sekhar Rao ◽  
N.V.Ramana Rao
Keyword(s):  
Mechanical Properties ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
High Strength ◽  
Geopolymer Concrete ◽  
Green House Gases ◽  
Green House ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

The utilisation of pozzolanic materials as the replacement to conventional cement material have the potentiality to mitigate the pollution caused by the émission of carbon based green house gases which are a main source for global warming problem. For every production of 1 ton of cement it was approximated that the emission of carbon based green house gases are about 1 ton. Keeping this in view, a new material called Geopolymer which was first coined by Davidovits has gained a lot of interest by the researchers. In this study, different molarity variations of NaOH in the order of 4M, 6M, 8M, 10M, 12M and 14M and also the blending of  mineral admixtures like Fly Ash and Ground Granulated Blast Furnace Slag with percentages (50%+50%) and the mechanical properties of normal M30 and high strength grade M70 binary blended Geopolymer concrete were studied after 28 days of ambient curing and were reported. The test results revealed that the effect of molar concentration of NaOH at 12 M is effective and the optimum replacement of mineral composition of source materials is (50%+50%) fly ash and ground granulated blast furnace slag.  

Sign in / Sign up

Export Citation Format

Share Document