scholarly journals Draught requirements of enamel coated animal drawn mouldboard plough

2012 ◽  
Vol 51 (No. 2) ◽  
pp. 56-62 ◽  
Author(s):  
I. A Loukanov ◽  
J. Uziak ◽  
J. Michálek

The power requirement of tillage implements is an important design consideration particularly for animal-drawn implements where the power is limited. The paper presents the possibility of reduction in the draught requirements of animal-drawn mouldboard plough by using enamel coating on the soil-engaged components such as the mouldboard, share and the landside. Trials were conducted to compare enamel-coated Maun Series single mouldboard plough (manufactured by Zimplow Limited, Bulawayo,Zimbabwe) with similar uncoated plough, both animal-drawn, under comparable working conditions. Experiments were done at 25% and 32% d.b. soil moisture content on a red clay soil inZimbabwe. The parameters measured in evaluating the draught performance of both ploughs were the tractive effort (pull), speed of ploughing, depth and width of ploughing, and soil conditions (i.e. soil moisture content, soil bulk density and soil penetration resistance). It was found that for similar working conditions the enamel coating reduced the specific draught by 20 to 26% depending upon soil moisture content.

2007 ◽  
Vol 3 (1) ◽  
pp. 115-129
Author(s):  
Ivan Loukanov ◽  
Jacek Uziak

The effect of enamel-coating on the draught performance of an animal-drawn mouldboard plough was studied. A single furrow swing mouldboard plough-Maun Series, and the same type enamel-coated plough both ox-drawn, are compared under similar working conditions such as soil moisture content, depth and width of cut and approximately constant speed of ploughing. It was found that the enamel-coating reduces both the plough draught and the specific draught. The percentage reduction of the plough draught for enamel-coated plough compared to uncoated plough varied from 12.7% at 25% soil moisture content to 18.1% at 32% soil moisture content (dry basis). It was also found that the percentage reduction of the specific draught achieved with the enamel-coated plough in comparison with the uncoated plough varied from 20.3% at 32% soil moisture content to 25.7% at 25% soil moisture content (dry basis).


Author(s):  
Y. A. Unguwanrimi ◽  
A. M. Sada ◽  
G. N. Ugama ◽  
H. S. Garuba ◽  
A. Ugoani

Draft requirements of two animal – drawn (IAR) weeders operating on loam soil were determined in the study. The implements include a straddle row weeder and an emcot attached rotary weeder evaluated under the same soil conditions, using a pair of white Fulani breed of oxen. The animal draft requirement was first estimated from the animal ergonomics measurements. Using area of 0.054 hectare as experimental plot for each implement the draft requirement of each implement was investigated after taking soil samples for soil moisture content and bulk density determinations. The implements tested showed variation in their average draft requirement. The straddle row weeder had the highest value of 338.15 N respectively while the emcot attached rotary weeder had the lowest value of 188.12 N with 47.03%, respectively. The average soil moisture contents and bulk density were 13.0% and 1.46%/cm3, respectively.


2020 ◽  
Vol 13 ◽  
pp. 117862212094806 ◽  
Author(s):  
MJ Marques ◽  
M Ruiz-Colmenero ◽  
R Bienes ◽  
A García-Díaz ◽  
B Sastre

The study of alternative soil managements to tillage, based on the evidence of climate change in the Mediterranean basin, is of great importance. Summer and autumn are critical seasons for soil degradation due to the high-intensity, short-duration storms. Vineyards are vulnerable, especially on steep slopes. The particular effects of storms over the years under different soil conditions due to different management practices are not frequently addressed in the literature. The aim of this study was to examine the differences between runoff and soil moisture patterns influenced by 2 treatments: traditional tillage (Till) and a permanent cover crop. A shallow-rooted grass species Brachypodium distachyon (L.) P. Beauv. with considerable density coverage was selected as cover crop. This annual species was seeded once in the first year and then allowed to self-seed the following years. Tillage was performed at least twice in spring to a 10- to 15-cm depth and once in late autumn at a depth of 20 to 35 cm. Rainfall simulation experiments were performed, 1 year after treatments, using high-intensity rainfall on closed plots of 2 m2, located in the middle strips of the vineyard with different treatments. The effects of simulated rainfall experiments were determined in 3 different moments of the growth cycle of cultivar: (1) in summer with dry soils, (2) in early autumn with moderate soil moisture, and (3) in autumn with wet soils. During the 2-year trial, the soil moisture level in the soil upper layer (0-10 cm) was higher for Till treatment (14.1% ± 2.4%) compared with that for cover crop treatment (12.3% ± 2.0%). However, soil moisture values were more similar between treatments at 35 cm depth (12% ± 1%), with the exception of spring and autumn; in spring, water consumption in the cover crop treatment was the highest, and the moisture level at 35 cm depth was reduced (12%) compared with that for Till treatment (13%). In autumn, in cover crop treatment, higher water infiltration rate in soils led to higher soil moisture content at 35 cm (11%) compared with that of Till treatment (10%). The effects of simulated rainfall experiments on runoff and infiltration under different soil conditions and management practices vary seasonally. Runoff was significantly higher in summer for cover crop treatment (11%) as compared with that for Till management (1%), but significantly lower (3%) with wetter soils than for Till treatment (22%) in autumn. Thus, the simulation experiments with wet soils using cover crops produced higher infiltration rates and, consequently, the higher soil moisture content in the following days. The difference between seasons is attributed to the greater porosity of soil under Till treatment in summer, which resulted from the shallow plowing (10-15 cm depth), carried out to reduce moisture competition between weeds. The effect of traditional spring plowing was short-lived. The infiltration of water increased by cover crop treatment as compared with tillage in autumn both before and after ripping. Management practices did not influence wine parameters, as no significant differences were found between wine organoleptic characteristics in the duo-trio wine tastings, similarly, no differences were found for alcoholic degree, acidity, reduced sugars, and pH; however, a trend for a positive increase in polyphenol contents was noticed. Therefore, properly managed to avoid water shortages, cover crops can be recommended for soil protection in semi-arid environments.


2000 ◽  
Vol 40 (6) ◽  
pp. 843 ◽  
Author(s):  
J. S. Day

Poor and uneven emergence of seedlings decreases the efficiency of sesame (Sesamum indicum) seed production. In a glasshouse study, seedling emergence was reduced by low soil moisture content (less than 20%, w/v) and by waterlogging (common in soils with small soil particles). Watering events that failed to raise soil moisture content above 20% caused most seeds to germinate (more than than 80%), but only some of these seeds emerged from the soil (less than 50%). Gibberellic acid pre-treatment of seeds (50 or 1000 mg/L) failed to improve emergence of seeds from soils with an initial soil moisture content less than 20%. This result supports previous reports suggesting that gibberellic acid treatment does not influence seedling emergence, and may only be useful to overcome seed dormancy in those sesame varieties where dormancy is a problem. For maximum emergence it is recommended that sesame seeds be sown in non-waterlogged soils and that soil moisture content be maintained above 20% for a number of days after sowing.


Geophysics ◽  
1998 ◽  
Vol 63 (4) ◽  
pp. 1357-1362 ◽  
Author(s):  
Robert D. Jefferson ◽  
Don W. Steeples ◽  
Ross A. Black ◽  
Tim Carr

Repeated shallow‐seismic experiments were conducted at a site on days with different near‐surface moisture conditions in unconsolidated material. Experimental field parameters remained constant to ensure comparability of results. Variations in the seismic data are attributed to the changes in soil‐moisture content of the unconsolidated material. Higher amplitudes of reflections and refractions were obtained under wetter near‐surface conditions. An increase in amplitude of 21 dB in the 100–300 Hz frequency range was observed when the moisture content increased from 18% to 36% in the upper 0.15 m (0.5 ft) of the subsurface. In the time‐domain records, highly saturated soil conditions caused large‐amplitude ringy wavelets that interfered with and degraded the appearance of some of the reflection information in the raw field data. This may indicate that an intermediate near‐surface moisture content is most conducive to the recording of high‐quality shallow‐seismic reflection data at this site. This study illustrates the drastic changes that can occur in shallow‐seismic data due to variations in near‐surface moisture conditions. These conditions may need to be considered to optimize the acquisition timing and parameters prior to collection of data.


HortScience ◽  
1992 ◽  
Vol 27 (6) ◽  
pp. 588a-588
Author(s):  
A. James Downer ◽  
Ben Faber ◽  
Richard White

Three polymers (a polyacrylamide, polyacrylate and a propenoate-propenamide copolymer) and three organic amendments (peat moss, wood shavings, and composted yardwaste) were incorporated at five rates in a sandy soil to 15cm depth. Soil moisture content was determined by time domain reflectometry and gravimetrically. Only the highest polymer rates (2928kg/ha [60#/1000sq.ft.]) produced significant increases in soil moisture content and reductions of soil bulk density. Peat moss and yardwaste increased soil water content while shavings decreased water content. Turf quality scores were not affected by polymers but were initially reduced by yardwaste and shavings.


2021 ◽  
Vol 46 (1) ◽  
pp. 22-30
Author(s):  
A.F. Tola ◽  
A.M. Sedara ◽  
O.B. Olatunde ◽  
A.A. Babalola

A study was conducted to determine the effect of soil moisture content, dynamic load and wheel slippage in measuring traction. A single wheel test rig was developed to enable fundamental research on traction studies on tropical soil at the department of Agricultural and Environmental Engineering of Federal University of Technology, Akure. This facility consists of a moving carriage with a trolley that moves in either forward or reverse directions on rails well above a soil bin powered by 2.2 kW, three phase induction motor. The present facility set up was able to operate in either towing test mode for tire motion resistance studies or driving test mode for tire net traction and tractive efficiency studies. The test tire on the moving carriage was powered to rotate by a motor with additional pull provided by a cable-pulley mechanism connected to a tower with hanging dead weights. All controls on the moving carriage were activated from the main control console. The developed facility was successfully tested to determine tractive efficiency for narrow wheels at a particular inflation pressure on clay soil. The single wheel test rig facility worked well and the research indicates that wheel load, wheel slippage, soil moisture content and inflation pressure has great effect on traction efficiency. Traction efficiency decreased as the wheel load and wheel slippage increased. The developed single wheel testing facility can perform traction tests in controlled soil conditions to study the effect of soil, tire and moisture parameters on the performance of the system.


Forests ◽  
2020 ◽  
Vol 11 (12) ◽  
pp. 1289
Author(s):  
Zuzana Dudáková (Allmanová) ◽  
Michal Allman ◽  
Ján Merganič ◽  
Katarína Merganičová

The paper deals with the damage of the remaining stand and soil caused by harvesting using three ground-based forest operations methods (harvester-forwarder/cable skidder/animal-tractor). It compares the impact of the most common harvesting technologies applied in Slovakia and in Central Europe and thus contributes with valuable information to the knowledge on the suitability of their application in forests stands dominated by broadleaved tree species. Harvesting was performed in five forest stands located at the University Forest Enterprise of Technical University in Zvolen in central Slovakia from August to October 2019. Damage to remaining trees was assessed from the point of its size, type, and position of damage along stem. We expected lower damage of remaining trees in stands where harvesters were used because of the applied cut-to-length short wood system and fully mechanized harvesting system. In addition, we examined soil bulk density and soil moisture content in ruts, space between ruts, and in undisturbed stand to reveal the impact of harvesting machinery on soil. We expected greater soil bulk densities and lower soil moisture content in these stands due to the greatest weight of harvesters and in ruts created by machinery compared with undisturbed stand soil. The highest percentage of damaged remaining trees equal to 20.47% and 23.36% was recorded for harvester forest operations, followed by skidder (19.44%) and animal forest operations with 19.86% and 14.47%. Factorial ANOVA confirmed significant higher soil compaction in stands where harvesters were used (higer bulk density) than in stands where skidding was performed with the skidder and animal power. Higher soil moisture content was recorded in ruts created by harvesters and the skidder. The lowest soil moisture content was in undisturbed stands irrespective of the applied forest operation method.


2011 ◽  
Vol 139 (12) ◽  
pp. 3848-3870 ◽  
Author(s):  
Clark Evans ◽  
Russ S. Schumacher ◽  
Thomas J. Galarneau

Abstract This study investigates the impact of abnormally moist soil conditions across the southern Great Plains upon the overland reintensification of North Atlantic Tropical Cyclone Erin (2007). This is tested by analyzing the contributions of three soil moisture–related signals—a seasonal signal, an along-track rainfall signal, and an early postlandfall rainfall signal—to the intensity of the vortex. In so doing, a suite of nine convection-permitting numerical simulations using the Advanced Research Weather Research and Forecasting model (WRF-ARW) is used. Of the signals tested, soil moisture contributions from the anomalously wet months preceding Erin are found to have the greatest positive impact upon the intensity of the vortex, though this impact is on the order of that from climatological soil moisture conditions. The greatest impact of the early rainfall signal contributions is found when it is added to the seasonal signal. Along-track rainfall during the simulation period has a minimal impact. Variations in soil moisture content result in impacts upon the boundary layer thermodynamic environment via boundary layer mixing. Greater soil moisture content results in weaker mixing, a shallower boundary layer, and greater moisture and instability. Differences in the intensity of convection that develops and its accompanying latent heat release aloft result in greater warm-core development and surface vortex intensification within the simulations featuring greater soil moisture content. Implications of these findings to the tropical cyclone development process are discussed. Given that the reintensification is shown to occur in, apart from land, an otherwise favorable environment for tropical cyclone development and results in a vortex with a structure similar to developing tropical cyclones, these findings provide new insight into the conditions under which tropical cyclones develop.


AGRICA ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 23-33
Author(s):  
Mariana Umin ◽  
Agustinus J.P. Anasaga

Characteristics of soil physical properties are the diversity of soil conditions based on structure, texture, soil color, and soil moisture content. Features of the physical properties of the soil influenced by several factors, including poor land management, which results in a decrease in fertility levels that includes physical, chemical, and biological soil characteristics.The method used in this study is the sample cluster method. Consists of a small group of units and then randomly selected as a representative of the population, all elements in the chosen cluster used as research samples. This study aims to determine the physical characteristics of soil texture, soil structure, soil color, and soil moisture content in cassava (Manihot esculenta Crantz) in Wologai Tengah Village.The results showed that the texture of the soil in cassava soil dominated by clay texture. The structure of the angular lumpy ground, soil color 10 YR 2/1 Black, and 10 YR 2/2 Very Dark Brown and had a soil moisture content of 37.4%. This soil type is an ideal soil type or classified as fertile to cultivate cassava plants.


Sign in / Sign up

Export Citation Format

Share Document