Preparation and Electrical Conductivity of Bismuth-Doped Antimonic Acids

1998 ◽  
Vol 548 ◽  
Author(s):  
K. Ozawa ◽  
Y. Sakka ◽  
M. Amano
Keyword(s):  
Aqueous Solution ◽  
Electrical Conductivity ◽  
Relative Humidity ◽  
Empirical Formula ◽  
Cell Parameter ◽  
Impedance Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Bismuth Content ◽  
Humidity Dependence

ABSTRACTBismuth-doped antimonic acids with the empirical formula Sb2O5·xBi2O3·nH2O (0 ≤ x ≤ 0.2) were prepared by reacting an H2O3, aqueous solution with Sb(O-i-C3H7)3and Bi(O-i-C3H7)3. X-ray diffraction confirmed that the anhydrous composites, Sb2O·xBi2O3(0 ≤ x ≤ 0. 1), are a single cubic Sb2O5phase, where the cubic cell parameter increases linearly from 10.277 to 10.380 Å with the bismuth content x. The electrical conductivity of the polycrystalline disks for Sb2O5·xBi2O3·nH2O (0 ≤ x ≤ 0.1) was evaluated by an ac impedance method at 19.5 °C under various conditions of relative humidity. The conductivity of Sb2O5·xBi2O3·nH2O with x = 0.1 was found to be high (1.0 × 10−3Scm−1) even at a relative humidity of 68.3%. There was a stronger humidity dependence than that of Sb2O5·xBi2O3·nH2O with x = 0.

Structural Study of a new Compound Based on Acid 1,4-Cyclohexanedicarboxylic (1,4-CDC)

2010 ◽  
Vol 6 (1) ◽  
pp. 891-896
Author(s):  
Manel Halouani ◽  
M. Dammak ◽  
N. Audebrand ◽  
L. Ktari
Keyword(s):  
Aqueous Solution ◽  
Water Molecules ◽  
Carboxyl Group ◽  
X Ray Diffraction ◽  
Compound I ◽  
Unit Cell Parameters ◽  
Monoclinic System ◽  
X Ray ◽  
Cell Parameters ◽  
Cyclohexanedicarboxylic Acid

One nickel 1,4-cyclohexanedicarboxylate coordination polymers, Ni2 [(O10C6H4)(COO)2].2H2O  (I), was hydrothermally synthesized from an aqueous solution of Ni (NO3)2.6H2O, (1,4-CDC) (1,4-CDC = 1,4-cyclohexanedicarboxylic acid) and tetramethylammonium nitrate. Compound (I) crystallizes in the monoclinic system with the C2/m space group. The unit cell parameters are a = 20.1160 (16) Å, b = 9.9387 (10) Å, c = 6.3672 (6) Å, β = 97.007 (3) (°), V= 1263.5 (2) (Å3) and Dx= 1.751g/cm3. The refinement converged into R= 0.036 and RW = 0.092. The structure, determined by single crystal X-ray diffraction, consists of two nickel atoms Ni (1) and Ni (2). Lots of ways of which is surrounded by six oxygen atoms, a carboxyl group and two water molecules.

scholarly journals Leaching Titaniferous Magnetite Concentrate by Alkaline Aqueous Solution

2021 ◽  
Author(s):  
Ke Guo ◽  
Shaoyan Wang ◽  
Renfeng Song ◽  
Zhiqiang Zhang
Keyword(s):  
Aqueous Solution ◽  
Alkali Concentration ◽  
Water Usage ◽  
X Ray Diffraction ◽  
High Concentration ◽  
X Ray ◽  
Iron Concentrate ◽  
Titaniferous Magnetite ◽  
Magnetite Concentrate ◽  
Kinetics Of

AbstractLeaching titaniferous magnetite concentrate with alkali solution of high concentration under high temperature and high pressure was utilized to improve the grade of iron in iron concentrate and the grade of TiO2 in titanium tailings. The titaniferous magnetite concentrate in use contained 12.67% TiO2 and 54.01% Fe. The thermodynamics of the possible reactions and the kinetics of leaching process were analyzed. It was found that decomposing FeTiO3 with NaOH aqueous solution could be carried out spontaneously and the reaction rate was mainly controlled by internal diffusion. The effects of water usage, alkali concentration, reaction time, and temperature on the leaching procedure were inspected, and the products were characterized by X-ray diffraction, scanning electron microscope, and energy dispersive spectroscopy, respectively. After NaOH leaching and magnetic separation, the concentrate, with Fe purity of 65.98% and Fe recovery of 82.46%, and the tailings, with TiO2 purity of 32.09% and TiO2 recovery of 80.79%, were obtained, respectively.

Structure and Conductivity of Iodine-Doped C60 Thin Films

1994 ◽  
Vol 359 ◽  
Author(s):  
Jun Chen ◽  
Haiyan Zhang ◽  
Baoqiong Chen ◽  
Shaoqi Peng ◽  
Ning Ke ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Room Temperature ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
Temperature Conductivity ◽  
Room Temperature Conductivity ◽  
X Ray ◽  
Thermally Activated ◽  
Order Of Magnitude

ABSTRACTWe report here the results of our study on the properties of iodine-doped C60 thin films by IR and optical absorption, X-ray diffraction, and electrical conductivity measurements. The results show that there is no apparent structural change in the iodine-doped samples at room temperature in comparison with that of the undoped films. However, in the electrical conductivity measurements, an increase of more that one order of magnitude in the room temperature conductivity has been observed in the iodine-doped samples. In addition, while the conductivity of the undoped films shows thermally activated temperature dependence, the conductivity of the iodine-doped films was found to be constant over a fairly wide temperature range (from 20°C to 70°C) exhibiting a metallic feature.

Removal of Heavy Metals from Aqueous Solution by Hydroxyapatite/Chitosan Composite

2013 ◽  
Vol 789 ◽  
pp. 176-179 ◽  
Author(s):  
Eny Kusrini ◽  
Nofrijon Sofyan ◽  
Dwi Marta Nurjaya ◽  
Santoso Santoso ◽  
Dewi Tristantini
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Metal Ions ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Removal Of Heavy Metals ◽  
Sem Micrograph ◽  
Pseudo Second Order ◽  
Chitosan Composite

Hydroxyapatite/chitosan (HApC) composite has been prepared by precipitation method and used for removal of heavy metals (Cr6+, Zn2+and Cd2+) from aqueous solution. The HAp and 3H7C composite with HAp:chitosan ratio of 3:7 (wt%) were characterized by Fourier transform infrared spectroscopy, X-ray diffraction and scanning electron microscopy-energy dispersive X-ray spectroscopy. The SEM results showed that HAp is spherical-shaped and crystalline, while chitosan has a flat structure. SEM micrograph of 3H7C composite reveals crystalline of HAp uniformly spread over the surface of chitosan. The crystal structure of HAp is maintained in 3H7C composite. Chitosan affects the adsorption capacity of HAp for heavy metal ions; it binds the metal ions as well as HAp. The kinetic data was best described by the pseudo-second order. Surface adsorption and intraparticle diffusion take place in the mechanism of adsorption process. The binding of HAp powder with chitosan made the capability of composite to removal of Cr6+, Zn2+and Cd2+from aqueous solution effective. The order of removal efficiency (Cr6+> Cd2+> Zn2+) was observed.

Low-temperature powder X-ray diffraction measurements in vacuum: analysis of the thermal displacement of copper

2016 ◽  
Vol 49 (1) ◽  
pp. 110-119 ◽  
Author(s):  
Nanna Wahlberg ◽  
Niels Bindzus ◽  
Sebastian Christensen ◽  
Jacob Becker ◽  
Ann-Christin Dippel ◽  
...  
Keyword(s):  
Distribution Function ◽  
Probability Distribution Function ◽  
Cell Parameter ◽  
Atomic Displacement ◽  
Cryogenic Temperatures ◽  
X Ray Diffraction ◽  
Atomic Displacement Parameter ◽  
Thermal Displacement ◽  
X Ray ◽  
Helium Gas

A serious limitation of the all-in-vacuum diffractometer reported by Straasø, Dippel, Becker & Als-Nielsen [J. Synchrotron Rad.(2014),21, 119–126] has so far been the inability to cool samples to near-cryogenic temperatures during measurement. The problem is solved by placing the sample in a jet of helium gas cooled by liquid nitrogen. The resulting temperature change is quantified by determining the change in unit-cell parameter and atomic displacement parameter of copper. The cooling proved successful, with a resulting temperature of ∼95 (3) K. The measured powder X-ray diffraction data are of superb quality and high resolution [up to sinθ/λ = 2.2 Å−1], permitting an extensive modelling of the thermal displacement. The anharmonic displacement of copper was modelled by a Gram–Charlier expansion of the temperature factor. As expected, the corresponding probability distribution function shows an increased probability away from neighbouring atoms and a decreased probability towards them.

scholarly journals Linear Structural Trends and Multi-Phase Intergrowths in Helvine-Group Minerals, (Zn,Fe,Mn)8[Be6Si6O24]S2

Minerals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 325
Author(s):  
Sytle Antao
Keyword(s):  
Cell Parameter ◽  
Structural Parameters ◽  
Unit Cell ◽  
Fluid Composition ◽  
Ternary Solid Solution ◽  
X Ray Diffraction ◽  
X Ray ◽  
The Difference ◽  
Multi Phase ◽  
And Diffusion

Synchrotron high-resolution powder X-ray diffraction (HRPXRD) and Rietveld structure refinements were used to examine the crystal structure of single phases and intergrowths (either two or three phases) in 13 samples of the helvine-group minerals, (Zn,Fe,Mn)8[Be6Si6O24]S2. The helvine structure was refined in the cubic space group P4¯3n. For the intergrowths, simultaneous refinements were carried out for each phase. The structural parameters for each phase in an intergrowth are only slightly different from each other. Each phase in an intergrowth has well-defined unit-cell and structural parameters that are significantly different from the three endmembers and these do not represent exsolution or immiscibility gaps in the ternary solid-solution series. The reason for the intergrowths in the helvine-group minerals is not clear considering the similar radii, identical charge, and diffusion among the interstitial M cations (Zn2+, Fe2+, and Mn2+) that are characteristic of elongated tetrahedral coordination. The difference between the radii of Zn2+ and Mn2+ cations is 10%. Depending on the availability of the M cations, intergrowths may occur as the temperature, pressure, fugacity fS2, and fluid composition change on crystallization. The Be–Si atoms are fully ordered. The Be–O and Si–O distances are nearly constant. Several structural parameters (Be–O–Si bridging angle, M–O, M–S, average <M–O/S>[4] distances, and TO4 rotational angles) vary linearly with the a unit-cell parameter across the series because of the size of the M cation.

scholarly journals Investigation and Modeling of the Electrical Conductivity of Graphene Nanoplatelets-Loaded Doped-Polypyrrole

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1034
Author(s):  
Oladipo Folorunso ◽  
Yskandar Hamam ◽  
Rotimi Sadiku ◽  
Suprakas Sinha Ray ◽  
Neeraj Kumar
Keyword(s):  
Electrical Conductivity ◽  
Structural Changes ◽  
Spherical Shape ◽  
Graphene Nanoplatelets ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
X Ray ◽  
Thermogravimetric Analyzer ◽  
Energy Storage Applications ◽  
Electrical Conductivity Data

In this study, a hybrid of graphene nanoplatelets with a polypyrrole having 20 wt.% loading of carbon-black (HGPPy.CB20%), has been fabricated. The thermal stability, structural changes, morphology, and the electrical conductivity of the hybrids were investigated using thermogravimetric analyzer, differential scanning calorimeter, X-ray diffraction analyzer, scanning electron microscope, and laboratory electrical conductivity device. The morphology of the hybrid shows well dispersion of graphene nanoplatelets on the surface of the PPy.CB20% and the transformation of the gravel-like PPy.CB20% shape to compact spherical shape. Moreover, the hybrid’s electrical conductivity measurements showed percolation threshold at 0.15 wt.% of the graphene nanoplatelets content and the curve is non-linear. The electrical conductivity data were analyzed by comparing different existing models (Weber, Clingerman and Taherian). The results show that Taherian and Clingerman models, which consider the aspect ratio, roundness, wettability, filler electrical conductivity, surface interaction, and volume fractions, closely described the experimental data. From these results, it is evident that Taherian and Clingerman models can be modified for better prediction of the hybrids electrical conductivity measurements. In addition, this study shows that graphene nanoplatelets are essential and have a significant influence on the modification of PPy.CB20% for energy storage applications.

Kummerite, Mn2+Fe3+Al(PO4)2(OH)2·8H2O, a new laueite-group mineral from the Hagendorf Süd pegmatite, Bavaria, with ordering of Al and Fe3+

2016 ◽  
Vol 80 (7) ◽  
pp. 1243-1254 ◽  
Author(s):  
I. E. Grey ◽  
E. Keck ◽  
W. G. Mumme ◽  
A. Pring ◽  
C. M. Macrae ◽  
...  
Keyword(s):  
Electron Microprobe ◽  
Empirical Formula ◽  
X Ray Diffraction ◽  
Unit Cell Parameters ◽  
Calculated Density ◽  
Group Mineral ◽  
X Ray ◽  
Cell Parameters ◽  
Octahedral Sites ◽  
Phosphate Mineral

AbstractKummerite, ideally Mn2+Fe3+A1(PO4)2(OH)2.8H2O, is a new secondary phosphate mineral belonging to the laueite group, from the Hagendorf-Süd pegmatite, Hagendorf, Oberpfalz, Bavaria, Germany. Kummerite occurs as sprays or rounded aggregates of very thin, typically deformed, amber yellow laths. Cleavage is good parallel to ﹛010﹜. The mineral is associated closely with green Zn- and Al-bearing beraunite needles. Other associated minerals are jahnsite-(CaMnMn) and Al-bearing frondelite. The calculated density of kummerite is 2.34 g cm 3. It is optically biaxial (-), α= 1.565(5), β = 1.600(5) and y = 1.630(5), with weak dispersion. Pleochroism is weak, with amber yellow tones. Electron microprobe analyses (average of 13 grains) with H2O and FeO/Fe2O3 calculated on structural grounds and normalized to 100%, gave Fe2O3 17.2, FeO 4.8, MnO 5.4, MgO 2.2, ZnO 0.5, Al2O3 9.8, P2O5 27.6, H2O 32.5, total 100 wt.%. The empirical formula, based on 3 metal apfu is (Mn2+0.37Mg0.27Zn0.03Fe2+0.33)Σ1.00(Fe3+1.06Al0. 94)Σ2.00PO4)1.91(OH)2.27(H2O)7.73. Kummerite is triclinic, P1̄, with the unit-cell parameters of a = 5.316(1) Å, b =10.620(3) Å , c = 7.118(1) Å, α = 107.33(3)°, β= 111.22(3)°, γ = 72.22(2)° and V= 348.4(2) Å3. The strongest lines in the powder X-ray diffraction pattern are [dobs in Å(I) (hkl)] 9.885 (100) (010); 6.476 (20) (001); 4.942 (30) (020); 3.988 (9) (̄110); 3.116 (18) (1̄20); 2.873 (11) (1̄21). Kummerite is isostructural with laueite, but differs in having Al and Fe3+ ordered into alternate octahedral sites in the 7.1 Å trans-connected octahedral chains.

Sign in / Sign up

Export Citation Format

Share Document