Improved Soi Films By High Dose Oxygen Implantation and Lamp Annealing

1985 ◽  
Vol 53 ◽  
Author(s):  
G. K. Celler ◽  
P. L. F. Hemment ◽  
K. W. West ◽  
J. M. Gibson
Keyword(s):  
High Speed ◽  
Ion Beam ◽  
Silicon On Insulator ◽  
High Dose ◽  
Cmos Circuits ◽  
Radiation Hardened ◽  
Silicon On Insulator Technology ◽  
Annealing Procedure ◽  
Oxygen Precipitates ◽  
Sharp Interfaces

ABSTRACTIon beam synthesis of a buried SiO2 layer is an attractive silicon-on-insulator technology for high speed CMOS circuits and radiation hardened devices. We demonstrate here a new annealing procedure at 1405°C that produces silicon films of excellent quality, essentially free of oxygen precipitates and with sharp interfaces between the Si and the SiO2.

Structural changes in silicon-on-insulator material during post-implantation annealing

1986 ◽  
Vol 44 ◽  
pp. 736-737
Author(s):  
C. O. Jung ◽  
S. J. Krause ◽  
S.R. Wilson
Keyword(s):  
Integrated Circuits ◽  
Oxide Layer ◽  
High Speed ◽  
Structural Changes ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Quality ◽  
Radiation Hardened ◽  
Post Implantation ◽  
Very High

Silicon-on-insulator (SOI) structures have excellent potential for future use in radiation hardened and high speed integrated circuits. For device fabrication in SOI material a high quality superficial Si layer above a buried oxide layer is required. Recently, Celler et al. reported that post-implantation annealing of oxygen implanted SOI at very high temperatures would eliminate virtually all defects and precipiates in the superficial Si layer. In this work we are reporting on the effect of three different post implantation annealing cycles on the structure of oxygen implanted SOI samples which were implanted under the same conditions.

TEM study of buried cobalt disilicide layers formed by ion implantation: Identification of cobalt monosilicide inclusions

1990 ◽  
Vol 48 (4) ◽  
pp. 576-577
Author(s):  
A. De Veirman ◽  
J. Van Landuyt ◽  
K.J. Reeson ◽  
R. Gwilliam ◽  
C. Jeynes ◽  
...  
Keyword(s):  
Ion Implantation ◽  
Annealing Treatment ◽  
Silicon On Insulator ◽  
High Dose ◽  
Nitrogen Flow ◽  
Cobalt Disilicide ◽  
Transmission Electron ◽  
Beam Heating ◽  
Co Concentration ◽  
Silicon On Insulator Technology

In analogy to the formation of SIMOX (Separation by IMplanted OXygen) material which is presently the most promising silicon-on-insulator technology, high-dose ion implantation of cobalt in silicon is used to synthesise buried CoSi2 layers. So far, for high-dose ion implantation of Co in Si, only formation of CoSi2 is reported. In this paper it will be shown that CoSi inclusions occur when the stoichiometric Co concentration is exceeded at the peak of the Co distribution. 350 keV Co+ ions are implanted into (001) Si wafers to doses of 2, 4 and 7×l017 per cm2. During the implantation the wafer is kept at ≈ 550°C, using beam heating. The subsequent annealing treatment was performed in a conventional nitrogen flow furnace at 1000°C for 5 to 30 minutes (FA) or in a dual graphite strip annealer where isochronal 5s anneals at temperatures between 800°C and 1200°C (RTA) were performed. The implanted samples have been studied by means of Rutherford Backscattering Spectroscopy (RBS) and cross-section Transmission Electron Microscopy (XTEM).

Characterization and Isolation Techniques in Silicon on Insulator Technology Microprocessor Designs

2000 ◽  
Author(s):  
T. Kane ◽  
M. Cambra ◽  
M. Tenney ◽  
P. McGinnis ◽  
A. Domenicucci ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Failure Modes ◽  
Ion Beam ◽  
Silicon On Insulator ◽  
Scanning Capacitance Microscopy ◽  
Isolation Techniques ◽  
Silicon On Insulator Technology ◽  
Soi Technology

Abstract This paper discusses the challenges involved in testing microprocessors incorporating silicon-on-insulator (SOI) technology and assesses new characterizations tools, such as scanning capacitance microscopy (SCM), focused ion beam (FIB) analysis, and AFM electrical probing, that show promise when used to examine SOI device anomalies and failure modes.

Precipitation in silicon-on-insulator material during high- temperature annealing

1987 ◽  
Vol 45 ◽  
pp. 254-255
Author(s):  
S. J. Krause ◽  
C. O. Jung ◽  
S.R. Wilson
Keyword(s):  
High Temperature ◽  
Integrated Circuits ◽  
Annealing Time ◽  
High Speed ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
Precipitate Size ◽  
High Dose ◽  
High Temperature Annealing ◽  
Implantation Energy

Silicon-on-insulator (SOI) structure by high dose oxygen implantation (SIMOX) has excellent potential for use in radiation hardened and high speed integrated circuits. Device fabrication in SIMOX requires a high quality superficial Si layer above the buried oxide layer. Previously we reported on the effect of heater temperature, background doping, and annealing cycle on precipitate size, density, and location in the superficial Si layer. Precipitates were not eliminated with our processing conditions, but various authors have recently reported that high temperature annealing of SIMOX, from 1250°C to 1405°C, eliminates virtually all precipitates in the superficial Si layer. However, in those studies there were significant differences in implantation energy and dose and also annealing time and temperature. Here we are reporting on the effect of annealing time and temperature on the formation and changes in precipitates.

Laser Recrystallization and 3D Integration

1984 ◽  
Vol 35 ◽  
Author(s):  
J.P. Colinge
Keyword(s):  
Single Crystal ◽  
Grain Boundaries ◽  
High Speed ◽  
Silicon On Insulator ◽  
Cmos Circuits ◽  
3D Integration ◽  
Stages Of Development ◽  
3D Ics ◽  
Laser Recrystallization ◽  
Integrated Structures

ABSTRACTThere are various methods for producing device-worthy Silicon-on-Insulator films, most, however, are unsuitable for fabrication of 3D integrated structures. The laser recrystallization technique is currently the only one which has produced single-crystal devices for 3D ICs. Improvements on this technique have been such that defects such as grain boundaries can be localized and even eliminated. High speed CMOS circuits with VLSI features have been realized as well as new devices which take advantage of the 3D arrangement of vertically integrated structures. Although 3D integration is still in the early stages of development, it has already opened up new perspectives for applications such as high speed circuits, dense memories, and sensors.

Assessment of Silicon—On—Insulator Technologies for Vlsi

1985 ◽  
Vol 53 ◽  
Author(s):  
B-Y. Tsaur
Keyword(s):  
High Performance ◽  
Cost Effective ◽  
Silicon On Insulator ◽  
Current Status ◽  
High Dose ◽  
Future Prospects ◽  
Device Structures ◽  
Radiation Hardened ◽  
Near Term ◽  
Soi Technology

ABSTRACTA high—performance, cost—effective silicon—on—insulator (SOI) technology would have important near—term applications in radiation—hardened electronics and longer term applications in submicrometer VLSI. The advantages of SOI over bulk Si technology for these applications will be outlined, and CMOS, CJFET, andbipolar device structures being developed for SOI will be discussed. The current status and future prospects of the two most promising SOI technologies —— beam recrystallization and high—dose oxygen implantation —— will be reviewed, with emphasis on such issues critical to commercialization as material quality and manufacturing feasibility.

Evolution and Future Trends of SIMOX Material

MRS Bulletin ◽  
1998 ◽  
Vol 23 (12) ◽  
pp. 25-29 ◽  
Author(s):  
Steve Krause ◽  
Maria Anc ◽  
Peter Roitman
Keyword(s):  
High Temperature ◽  
Low Power ◽  
High Speed ◽  
New Technologies ◽  
Low Voltage ◽  
Semiconductor Industry ◽  
High Energy ◽  
Silicon On Insulator ◽  
High Dose ◽  
High Temperature Annealing

Oxygen-implanted silicon-on-insulator (SOI) material, or SIMOX (separation by implantation of oxygen), is another chapter in the continuing development of new material technologies for use by the semiconductor industry. Building integrated circuits (ICs) in a thin layer of crystalline silicon on a layer of silicon oxide on a silicon substrate has benefits for radiationhard, high-temperature, high-speed, low-voltage, and low-power operation, and for future device designs. Historically the first interest in SIMOX was for radiation-hard electronics for space, but the major application of interest currently is low-power, high-speed, portable electronics. Silicon-on-insulator also avoids the disadvantage of a completely different substrate such as sapphire or gallium arsenide. Formation of a buried-oxide (BOX) layer by high-energy, high-dose, oxygen ion implantation has the advantage that the ion-implant dose can be made extremely precise and extremely uniform. However the silicon and oxide layers are highly damaged after the implant, so high-temperature annealing sequences are required to restore devicequality material. In fact SIMOX process development necessitated the development of new technologies for high-dose implantation and high-temperature annealing.

Origin of the defect structures in oxygen-implanted silicon-on-insulator material

1993 ◽  
Vol 51 ◽  
pp. 1108-1109
Author(s):  
D. Venables ◽  
S.J. Krause ◽  
J.D. Lee ◽  
J.C. Park ◽  
P. Roitman
Keyword(s):  
High Temperature ◽  
High Speed ◽  
Silicon Layer ◽  
Dark Field ◽  
Silicon On Insulator ◽  
High Dose ◽  
Defect Structures ◽  
Plan View ◽  
High Temperature Anneal ◽  
Single Oxygen

Silicon-on-insulator material fabricated by high-dose oxygen implantation (known as SIMOX) has been used for high speed and radiation hard devices and is under consideration for use in low power applications. However, a continuing problem has been crystalline defects in the top silicon layer. SIMOX is fabricated by two distinct methods: a single oxygen implant to a dose of 1.8×l018 cm-2 followed by a high-temperature anneal (≥1300°C, 4-6 hr) or by multiple lower dose implants (∼6×l017 cm-2) with high-temperature anneals after each implant. To date, there has been no systematic comparison of the defect structures produced by these two fabrication methods. Therefore, we have compared the defect structure and densities in multiple vs. single implant wafers. In this paper we describe the origin and characteristics of the defect structures in SIMOX and show how their densities are controlled by the processing method and conditions.Silicon (100) wafers were implanted in a high current implanter at ∼620°C to doses of 1.8×l018 or 0.6/0.6/0.6×l018 cm-2 and annealed at 1325°C, 4 hr in 0.5% or 5% O2 in Ar. Cross-section (XTEM) and plan-view (PTEM) samples were studied with bright field and weak beam dark field techniques in a transmission electron microscope operating at 200 keV.

Microstructural Characterization of High Dose Oxygen Implanted Silicon

1986 ◽  
Vol 74 ◽  
Author(s):  
J. L. Batstone ◽  
Alice E. White ◽  
K. T. Short ◽  
J. M. Gibson ◽  
D. C. Jacobson
Keyword(s):  
Microstructural Characterization ◽  
Amorphous Structure ◽  
Silicon On Insulator ◽  
High Dose ◽  
High Resolution Imaging ◽  
Buried Oxide ◽  
Transmission Electron ◽  
Resolution Imaging ◽  
Silicon On Insulator Technology

AbstractThe microstructure of oxygen implanted silicon for use in silicon-on- insulator technology has been examined by transmission electron microscopy. A variety of buried oxide layers prepared using oxygen doses below and above that required for stoichiometric SiO2 formation have been studied. High resolution imaging in crosssection has revealed exceptionally flat Si-SiO2 interfaces, comparable to the best thermally grown Si-SiO2 interfaces. Examination of as-implanted material shows a complex interwoven crystalline/amorphous structure which evolves during high temperature (1350–1400° C) annealing into a buried oxide layer.

Analysis of Silicon-On-Insulator Structures Formed By Oxygen Ion Implantation

1985 ◽  
Vol 43 ◽  
pp. 300-301
Author(s):  
N. Lewis ◽  
E. L. Hall ◽  
A. Mogro-Campero ◽  
R. P. Love
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Single Crystal Silicon ◽  
Silicon Layer ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Dose ◽  
Crystal Silicon ◽  
Oxygen Ion ◽  
Oxygen Ion Implantation

The formation of buried oxide structures in single crystal silicon by high-dose oxygen ion implantation has received considerable attention recently for applications in advanced electronic device fabrication. This process is performed in a vacuum, and under the proper implantation conditions results in a silicon-on-insulator (SOI) structure with a top single crystal silicon layer on an amorphous silicon dioxide layer. The top Si layer has the same orientation as the silicon substrate. The quality of the outermost portion of the Si top layer is important in device fabrication since it either can be used directly to build devices, or epitaxial Si may be grown on this layer. Therefore, careful characterization of the results of the ion implantation process is essential.

Sign in / Sign up

Export Citation Format

Share Document