The Effects of Hydrogen Dilution on VOC in a-Si:H Pin Solar Cells

1997 ◽  
Vol 467 ◽  
Author(s):  
Qi Wang ◽  
Richard S. Crandall ◽  
Daxing Han

ABSTRACTWe study the effects of hydrogen dilution on the open circuit voltage of a-Si:H pin solar cells fabricated by rf glow discharge growth. We keep the p and n layers the same and only vary the i layer properties. A normal a-Si:H i layer, an H-diluted i layer, and a thin H-diluted layer inserted between p and normal i layer are selected for this study. We measure the JV characteristics and the internal electric field distribution using a transient-null-current technique both in annealed and light soaked states. We find that hydrogen dilution does stabilize the Voc either in a bulk H-diluted i layer or in a thin layer between p and normal i layer after 100 hours AMI sun light soaking. From dark IV measurement, both H-diluted cells show little change in current at voltage near Voc before and after light soaking; while the normal a-Si:H cell does show a noticeable change. Also the internal field measurements find a stronger electric field starting from p and i interface for both H-diluted cells compared to the normal a-Si:H cell. Furthermore, there are no measurable changes in the field profiles after 100 hour AMI light-soaking for both H-diluted and normal a-Si cells. All these suggest that hydrogen dilution increases the field strength near p and i interface, which is the key that leads to a more stable Voc of H-diluted cells.

1997 ◽  
Vol 467 ◽  
Author(s):  
Daxing Han ◽  
Chenan Yeh ◽  
Keda Wang ◽  
Qiwang

ABSTRACTWe demonstrate that the internal field of a thin a-Si:H pin solar cells can be measured using the transient-null-current method. This method was previously developed to measure the internal field profile in a-Si alloy Schottky barrier. The internal electric field profile was determined by measuring the forward-bias voltages that tune the transient photocurrents generated by a pulsed laser at a various wavelengths to zero. We adopt the same technique to a-Si:H p-i-n solar cells. In the case of p-i-n structure, we need to consider both space charge contributed by photogenerated carriers and carrier recombination which disturb the internal field. We use two critical conditions to minimize these effects. (1) To limit the contribution of photocarriers to space-charge distribution, the total charge collected is less than 10−10 C per pulse, and a repetition rate 1 Hz is used to ensure that the diode remains close to its equilibrium state. (2) The measuring time window is about 1 – 6 μs following the displacement current. Typically the RC constant of diode is < 1 μs and the rise time of the forward-bias recombination current is 6.0 × μs. We apply the signal average to process the forward-bias voltage. The error is within ± 0.05 V. With this technique we can study the effect of variety of structure design or processing on the device performance.


1995 ◽  
Vol 377 ◽  
Author(s):  
Jae-Hee Lee ◽  
Jae-Seog Koh ◽  
Jin Jang

ABSTRACTHydrogenated amorphous silicon (a-Si:H) solar cells are prepared by plasma enhanced chemical vapor deposition (PECVD). Before quenching the solar cells, the short circuit current (Jsc), open circuit voltage (Voc), fill factor (F. F.) and conversion efficiency (η) are 17.79 mA/cm2, 0.79 V, 53.29, and 7.49 %, respectively. After thermal quenchine the solar cells from 200°C, Jsc, Voc, F. F., and η are 18.64 mA/cm2, 0.8 V, 53.79, and 8.02 %, respectively. We investigated the thermal equilibrium processes of each P, I, and N layers. Also, we obtained the dark current-voltage characteristics of a-Si:H solar cells before and after quenching. We analyze the results in terms of the change of the internal electric field in a-Si:H solar cells, caused by the shift of the Fermi level of P layer toward valence band.


2021 ◽  
Vol 223 ◽  
pp. 110948
Author(s):  
Alban Lafuente-Sampietro ◽  
Katsuhisa Yoshida ◽  
Shenghao Wang ◽  
Shogo Ishizuka ◽  
Hajime Shibata ◽  
...  

2018 ◽  
Vol 68 (4) ◽  
pp. 381-386
Author(s):  
Mo Geun SO ◽  
Hyun-Jun JO ◽  
Young Hee MUN ◽  
Jong Su KIM* ◽  
Yeongho KIM ◽  
...  

2014 ◽  
Vol 1070-1072 ◽  
pp. 1011-1015
Author(s):  
Meng Song ◽  
Zuo Shuai Wang ◽  
Li Ren ◽  
Yi Zhang ◽  
Shi Feng Shen ◽  
...  

High temperature superconducting (HTS) cable termination is an important component of the HTS cable system, which functions to connect the HTS cable and the conventional cable accessory. The stress cones of the HTS cable termination can improve the internal electric field distribution and the electrical insulation strength of the cable termination. In this paper, the mathematical model and equivalent circuit model of the stress cones are built and the genetic algorithm is adopted to the design of 110-kV HTS cable terminal stress cone. The capacitance, radial electric field, axial electric field, voltage, insulation thickness and other parameters of the stress cone were compared before and after the optimization of the stress cone. Finally, the simulations of the stress cone with the optimized structure were made using finite-element analysis software COMSOL to test the optimization result.


2007 ◽  
Vol 1031 ◽  
Author(s):  
Shun-Wei Liu ◽  
Chih-Chien Lee ◽  
Ping-Tsung Huang ◽  
Chin-Ti Chen ◽  
Juen-Kai Wang

AbstractThe authors report the study of the dependence of the device performance of polymer solar cells based on single 50-nm heterojunction poly(3-hexylthiophene)/[6,6]-phenyl-C61-butyric acid methylester (P3HT/PCBM) layer on annealing process. Annealing before and after cathode deposition were performed for comparison. In the case of post-annealing at 150¢XC for 60 min., the device attains a conversion efficiency of 4.9%, a fill factor of 53 %, and an open-circuit voltage of 0.67 V. These values are comparable with the highest values reported previously. The annealing process is expected to modify the network morphology of the P3HT/PCBM layer. This study demonstrates that it is possible to attain good solar cell performance with the combination of single thin active layer and post-annealing treatment. This may open up an opportunity to fabricate tandem polymer solar cells.


1993 ◽  
Vol 297 ◽  
Author(s):  
Yuan-Min Li

Recent efforts to optimize undoped, glow-discharge hydrogenated amorphous silicon-carbon alloys (a-SiC:H) with 1.9-2.0 eV bandgaps for solar cell applications are reviewed. Hydrogen dilution coupled with relatively low substrate temperatures (below 200 °C) have led to great improvements in the optical and phototransport properties of a-SiC:H films. The issue of alternative carbon feedstocks other than methane (CH4) will be explored. The improved a-SiC:H alloys have resulted in solar cells with high open circuit voltages (V∞ > 1.0 volt) and high fill factors (> 0.7). Further, the a-SiC:H solar cell instability upon prolonged light exposure has been much reduced. Correlation will be made between the properties of bulk undoped a-SiC:H films and the performance of p-i-nsingle junction solar cells using corresponding a-SiC:H thin i-layers.


Author(s):  
Michael Stuckelberger ◽  
Arvind Shah ◽  
Janez Krc ◽  
Matthieu Despeisse ◽  
Fanny Meillaud ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document