Thermal Conductivity of Aluminum Nitride Thin Films

1990 ◽  
Vol 203 ◽  
Author(s):  
L. J. Shaw-Klein ◽  
S. J. Burns ◽  
S. D. Jacobs
Keyword(s):  
Thin Film ◽  
Thermal Conductivity ◽  
Laser Damage ◽  
High Oxygen Concentration ◽  
Damage Resistance ◽  
Sapphire Substrates ◽  
Transmission Electron ◽  
Fused Quartz ◽  
Possible Cause ◽  
Film Conductivity

ABSTRACTAnomalously low laser damage resistance thresholds have been observed in many thin film systems. Thermal conductivity values well below bulk have been suggested as a possible cause. A series of reactively sputtered AIN films were deposited on fused quartz and sapphire substrates. Their thermal conductivities were measured using the thermal comparator technique. Important factors contributing to the apparently large thermal resistance in the AIN films include film surfaces, small grain size, and high oxygen concentration. Preferred orientation and columnar morphology also affect film conductivity. Film microstructures were observed by transmission electron microscopy, and correlated with measured values of thermal conductivity.

scholarly journals Impacts of SiO2 planarization on optical thin film properties and laser damage resistance

2016 ◽  
Author(s):  
T. Day ◽  
H. Wang ◽  
E. Jankowska ◽  
B. A. Reagan ◽  
J. J. Rocca ◽  
...  
Keyword(s):  
Thin Film ◽  
Laser Damage ◽  
Film Properties ◽  
Damage Resistance ◽  
Optical Thin Film

Transmission Electron Microscopy of oriented Co84Cr14Ta2 thin films for longitudinal magnetic recording

1991 ◽  
Vol 49 ◽  
pp. 756-757
Author(s):  
T. P. Nolan
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Low Cost ◽  
Low Noise ◽  
Information Storage ◽  
High Coercivity ◽  
Magnetic Alloy ◽  
Magnetic Media ◽  
Transmission Electron

Thin film magnetic media are being used as low cost, high density forms of information storage. The development of this technology requires the study, at the sub-micron level, of morphological, crystallographic, and magnetic properties, throughout the depth of the deposited films. As the microstructure becomes increasingly fine, widi grain sizes approaching 100Å, the unique characterization capabilities of transmission electron microscopy (TEM) have become indispensable to the analysis of such thin film magnetic media.Films were deposited at 225°C, on two NiP plated Al substrates, one polished, and one circumferentially textured with a mean roughness of 55Å. Three layers, a 750Å chromium underlayer, a 600Å layer of magnetic alloy of composition Co84Cr14Ta2, and a 300Å amorphous carbon overcoat were then sputter deposited using a dc magnetron system at a power of 1kW, in a chamber evacuated below 10-6 torr and filled to 12μm Ar pressure. The textured medium is presently used in industry owing to its high coercivity, Hc, and relatively low noise. One important feature is that the coercivity in the circumferential read/write direction is significandy higher than that in the radial direction.

Some early history of replica techniques for electron microscopy

1992 ◽  
Vol 50 (2) ◽  
pp. 1076-1077
Author(s):  
Robert M. Fisher
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Optical Microscope ◽  
Early History ◽  
Bulk Materials ◽  
Thin Sections ◽  
Transmission Electron ◽  
Reflected Light ◽  
History Of ◽  
Electron Microscopes

By 1940, a half dozen or so commercial or home-built transmission electron microscopes were in use for studies of the ultrastructure of matter. These operated at 30-60 kV and most pioneering microscopists were preoccupied with their search for electron transparent substrates to support dispersions of particulates or bacteria for TEM examination and did not contemplate studies of bulk materials. Metallurgist H. Mahl and other physical scientists, accustomed to examining etched, deformed or machined specimens by reflected light in the optical microscope, were also highly motivated to capitalize on the superior resolution of the electron microscope. Mahl originated several methods of preparing thin oxide or lacquer impressions of surfaces that were transparent in his 50 kV TEM. The utility of replication was recognized immediately and many variations on the theme, including two-step negative-positive replicas, soon appeared. Intense development of replica techniques slowed after 1955 but important advances still occur. The availability of 100 kV instruments, advent of thin film methods for metals and ceramics and microtoming of thin sections for biological specimens largely eliminated any need to resort to replicas.

Electron Microscopy Studies of The Chemistry And Microstructure of BaF2 / YBa2Cu3O7-x Thin Films

1994 ◽  
Vol 52 ◽  
pp. 796-797
Author(s):  
J. L. Lee ◽  
C. A. Weiss ◽  
R. A. Buhrman ◽  
J. Silcox
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Thin Films ◽  
Scanning Transmission Electron Microscope ◽  
Atomic Scale ◽  
Island Growth ◽  
Multilayer Systems ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Mgo Substrate

BaF2 thin films are being investigated as candidates for use in YBa2Cu3O7-x (YBCO) / BaF2 thin film multilayer systems, given the favorable dielectric properties of BaF2. In this study, the microstructural and chemical compatibility of BaF2 thin films with YBCO thin films is examined using transmission electron microscopy and microanalysis. The specimen was prepared by using laser ablation to first deposit an approximately 2500 Å thick (0 0 1) YBCO thin film onto a (0 0 1) MgO substrate. An approximately 7500 Å thick (0 0 1) BaF2 thin film was subsequendy thermally evaporated onto the YBCO film.Images from a VG HB501A UHV scanning transmission electron microscope (STEM) operating at 100 kV show that the thickness of the BaF2 film is rather uniform, with the BaF2/YBCO interface being quite flat. Relatively few intrinsic defects, such as hillocks and depressions, were evident in the BaF2 film. Moreover, the hillocks and depressions appear to be faceted along {111} planes, suggesting that the surface is smooth and well-ordered on an atomic scale and that an island growth mechanism is involved in the evolution of the BaF2 film.

Growth kinetics of Al2Cu in an Al-1.5Cu thin film by in Situ TEM

1993 ◽  
Vol 51 ◽  
pp. 1172-1173
Author(s):  
M. Park ◽  
S.J. Krause ◽  
S.R. Wilson
Keyword(s):  
Thin Film ◽  
In Situ Tem ◽  
Collector Plate ◽  
Transmission Electron ◽  
Device Processing ◽  
Corrosion Susceptibility ◽  
Precipitation Phenomena ◽  
Semiconductor Chips ◽  
Kinetics Of

Cu alloying in Al interconnection lines on semiconductor chips improves their resistance to electromigration and hillock growth. Excess Cu in Al can result in the formation of Cu-rich Al2Cu (θ) precipitates. These precipitates can significantly increase corrosion susceptibility due to the galvanic action between the θ-phase and the adjacent Cu-depleted matrix. The size and distribution of the θ-phase are also closely related to the film susceptibility to electromigration voiding. Thus, an important issue is the precipitation phenomena which occur during thermal device processing steps. In bulk alloys, it was found that the θ precipitates can grow via the grain boundary “collector plate mechanism” at rates far greater than allowed by volume diffusion. In a thin film, however, one might expect that the growth rate of a θ precipitate might be altered by interfacial diffusion. In this work, we report on the growth (lengthening) kinetics of the θ-phase in Al-Cu thin films as examined by in-situ isothermal aging in transmission electron microscopy (TEM).

Palladium Nanowire Thin Films via Template Growth

2003 ◽  
Vol 775 ◽  
Author(s):  
Donghai Wang ◽  
David T. Johnson ◽  
Byron F. McCaughey ◽  
J. Eric Hampsey ◽  
Jibao He ◽  
...  
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Conductive Substrate ◽  
Palladium Nanowires ◽  
Efficient Route ◽  
Silica Thin Film

AbstractPalladium nanowires have been electrodeposited into mesoporous silica thin film templates. Palladium continually grows and fills silica mesopores starting from a bottom conductive substrate, providing a ready and efficient route to fabricate a macroscopic palladium nanowire thin films for potentially use in fuel cells, electrodes, sensors, and other applications. X-ray diffraction (XRD) and transmission electron microscopy (TEM) indicate it is possible to create different nanowire morphology such as bundles and swirling mesostructure based on the template pore structure.

Laser Damage Resistance of Photo-Thermo-Refractive Glass Bragg Gratings

2004 ◽  
Author(s):  
Leonid B. Glebov ◽  
Larissa N. Glebova ◽  
Vadim I. Smirnov ◽  
Mark Dubinskii ◽  
Larry D. Merkle ◽  
...  
Keyword(s):  
Bragg Gratings ◽  
Laser Damage ◽  
Damage Resistance

scholarly journals The impact of point defects in n-type GaN layers on thermal decomposition of InGaN/GaN QWs

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Mikolaj Grabowski ◽  
Ewa Grzanka ◽  
Szymon Grzanka ◽  
Artur Lachowski ◽  
Julita Smalc-Koziorowska ◽  
...  
Keyword(s):  
Quantum Wells ◽  
High Temperatures ◽  
Point Defects ◽  
X Ray Diffraction ◽  
Helium Ions ◽  
X Ray ◽  
Sapphire Substrates ◽  
Transmission Electron ◽  
The Impact ◽  
Ingan Quantum Wells

AbstractThe aim of this paper is to give an experimental evidence that point defects (most probably gallium vacancies) induce decomposition of InGaN quantum wells (QWs) at high temperatures. In the experiment performed, we implanted GaN:Si/sapphire substrates with helium ions in order to introduce a high density of point defects. Then, we grew InGaN QWs on such substrates at temperature of 730 °C, what caused elimination of most (but not all) of the implantation-induced point defects expanding the crystal lattice. The InGaN QWs were almost identical to those grown on unimplanted GaN substrates. In the next step of the experiment, we annealed samples grown on unimplanted and implanted GaN at temperatures of 900 °C, 920 °C and 940 °C for half an hour. The samples were examined using Photoluminescence, X-ray Diffraction and Transmission Electron Microscopy. We found out that the decomposition of InGaN QWs started at lower temperatures for the samples grown on the implanted GaN substrates what provides a strong experimental support that point defects play important role in InGaN decomposition at high temperatures.

Determination of Thermal Conductivity of Amorphous Silicon Thin Films via Non-Contacting Optical Probing

2006 ◽  
Vol 326-328 ◽  
pp. 689-692
Author(s):  
Seung Jae Moon
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Thermal Conductivity ◽  
Amorphous Silicon ◽  
Optical Transmission ◽  
Film Deposition ◽  
Transmission Measurement ◽  
Conductive Heat ◽  
Optical Transmission Measurement

The thermal conductivity of amorphous silicon (a-Si) thin films is determined by using the non-intrusive, in-situ optical transmission measurement. The thermal conductivity of a-Si is a key parameter in understanding the mechanism of the recrystallization of polysilicon (p-Si) during the laser annealing process to fabricate the thin film transistors with uniform characteristics which are used as switches in the active matrix liquid crystal displays. Since it is well known that the physical properties are dependent on the process parameters of the thin film deposition process, the thermal conductivity should be measured. The temperature dependence of the film complex refractive index is determined by spectroscopic ellipsometry. A nanosecond KrF excimer laser at the wavelength of 248 nm is used to raise the temperature of the thin films without melting of the thin film. In-situ transmission signal is obtained during the heating process. The acquired transmission signal is fitted with predictions obtained by coupling conductive heat transfer with multi-layer thin film optics in the optical transmission measurement.

Influence of Modulation Wavelength Induced Order on the Physical Properties of Nb/Rare Earth Superlattices

1984 ◽  
Vol 37 ◽  
Author(s):  
L. H. Greene ◽  
W. L. Feldmann ◽  
J. M. Rowell ◽  
B. Batlogg ◽  
R. Hull ◽  
...  
Keyword(s):  
Rare Earth ◽  
Room Temperature ◽  
Room Temperature Resistivity ◽  
Residual Resistance ◽  
Sapphire Substrates ◽  
Transmission Electron ◽  
Sputter Deposited ◽  
Residual Resistance Ratio ◽  
Temperature Resistivity ◽  
Modulation Wavelength

AbstractWe report the observation of a higher degree of preferred crystalline orientation in Nb/rare earth superlattices for modulation wavelengths in the range of 200 Å to 500 Å than that exhibited by single component films. All films and multilayers are sputter deposited onto room temperature sapphire substrates. Electronic transport measurements also show that the residual resistance ratio is higher and the room temperature resistivity is lower than for multilayers of either greater or lower periodicities. Transmission electron micrographs (TEM) showing excellent layering, grain size comparable to the layer thickness, and evidence of some degree of epitaxy are presented.

Sign in / Sign up

Export Citation Format

Share Document