Metastable Phases in Rapidly Solidified Aluminum-Rich Al-Fe Alloys

1982 ◽  
Vol 19 ◽  
Author(s):  
D. Shechtman ◽  
L.J. Swartzendruber
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Melt Spinning ◽  
Gamma Ray ◽  
Resonance Spectrum ◽  
Metastable Phase ◽  
Metastable Phases ◽  
Transmission Electron ◽  
Fe Alloys ◽  
Rapidly Solidified

ABSTRACTAluminum-rich Al-Fe binary alloys up to and including Al3Fe were prepared by melt spinning in order to study the metastable phase structure and its transformation following heat treatment. Transmission electron microscopy and nuclear gamma-ray resonance were utilized in the study. The rapidly solidified structure was found to contain up to three metastable phases. One of the phases, with a composition and a gamma-ray resonance spectrum appropriate for Al6Fe, has either a globular or a cellular morphology upon quenching.

Microstructures of Rapidly Solidified Aluminum Alloys

1983 ◽  
Vol 28 ◽  
Author(s):  
J.W. Zindel ◽  
J.T. Stanley ◽  
R.D. Field ◽  
H.L. Fraser
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Aluminum Alloys ◽  
Melt Spinning ◽  
Metastable Phase ◽  
Laser Surface ◽  
Metastable Phase Diagram ◽  
Transmission Electron ◽  
Ternary Additions ◽  
Rapidly Solidified

ABSTRACTAn investigation was performed to study the origin and stability of microstructures in rapidly solidified aluminum alloys. Al-Ni and Al-Fe base alloys were rapidly solidified by means of laser surface melting and melt spinning techniques. Microstructures were studied using optical and transmission electron microscopy. The effect of microstructure on mechanical properties was also studied using microhardness measurements. The origin of the observed microstructural constituents will be explained in terms of features of the metastable phase diagram. The effect of ternary additions on stability will also be considered.

Shock Synthesis of Nanocrystalline High -Pressure Phases in Semiconductors by High-Velocity Thermal Spray

2000 ◽  
Vol 638 ◽  
Author(s):  
R. Goswami ◽  
J. Parise ◽  
H. Herman ◽  
S. Sampath ◽  
R. Gambino ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Pressure ◽  
Thermal Spray ◽  
High Velocity ◽  
Metastable Phase ◽  
High Energy ◽  
Metastable Phases ◽  
Transmission Electron ◽  
Average Size

AbstractShock synthesis of nanocrystalline Si, Ge and CdTe was accomplished using high- velocity thermal spray. Si or Ge powders were injected into a high energy flame, created by a thermal spray gun, where the particles melt and accelerate to impact on a substrate. The shock wave generated by the sudden impact of the droplets propagated through the underlying deposits, which induces a phase transition to a high pressure form. The decompression of the high-pressure phase results in the formation of several metastable phases, as evidenced by transmission electron microscopy and x-ray diffraction studies. The peak pressure is estimated to be ≈23GPa with a pulse duration of 1-5 ns. Transmission electron microscopy revealed that the metastable phases of Si with a size range of 2 to 5 nm were dispersed within Si-I. In Ge, a metastable phase, ST-12, was observed. This is a decompression product of Ge-II which possesses the β-Sn type of structure. In the case of CdTe, a fine dispersion of hexagonal CdTe particles, embedded in cubic-CdTe with an average size of 2 nm was obtained.

scholarly journals Structure of Rapidly Solidified Al-Fe-Cr-Ce Alloy

2011 ◽  
Vol 465 ◽  
pp. 199-202 ◽  
Author(s):  
Alena Michalcová ◽  
Dalibor Vojtěch ◽  
Pavel Novák ◽  
Ivan Procházka ◽  
Jakub Čížek ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Transmission Electron Microscopy ◽  
Positron Annihilation ◽  
Melt Spinning ◽  
Positron Annihilation Spectroscopy ◽  
Transmission Electron ◽  
Rapidly Solidified ◽  
Thermal Stability Of

An alloy containing Al – 3wt.% Cr – 3wt.% Fe – 0.8wt. % Ce, was prepared by melt spinning. Structure of obtained ribbons was observed by light, scanning and transmission electron microscopy. It was found out that the structure is very fine. Microhardness of cross sectioned ribbons was also measured. Defects in structure were determined by positron annihilation spectroscopy. The thermal stability of the alloy was observed by comparing rapidly solidified ribbons and ribbons annealed at 400°C and at 500°C for 100 h

Devitrification products of rapidly solidified Ni-Nb amorphous alloys.

1990 ◽  
Vol 48 (4) ◽  
pp. 950-951
Author(s):  
G. A. Bertero ◽  
W.H. Hofmeister ◽  
N.D. Evans ◽  
J.E. Wittig ◽  
R.J. Bayuzick
Keyword(s):  
Electron Microscopy ◽  
Amorphous Structure ◽  
Sulphuric Acid Solution ◽  
X Ray Diffraction ◽  
High Fracture ◽  
Transmission Electron ◽  
Xrd Techniques ◽  
Rapidly Solidified ◽  
Electromagnetically Levitated

Rapid solidification of Ni-Nb alloys promotes the formation of amorphous structure. Preliminary results indicate promising elastic properties and high fracture strength for the metallic glass. Knowledge of the thermal stability of the amorphus alloy and the changes in properties with temperature is therefore of prime importance. In this work rapidly solidified Ni-Nb alloys were analyzed with transmission electron microscopy (TEM) during in-situ heating experiments and after isothermal annealing of bulk samples. Differential thermal analysis (DTA), scanning electron microscopy (SEM) and x-ray diffraction (XRD) techniques were also used to characterize both the solidification and devitrification sequences.Samples of Ni-44 at.% Nb were electromagnetically levitated, melted, and rapidly solidified by splatquenching between two copper chill plates. The resulting samples were 100 to 200 μm thick discs of 2 to 3 cm diameter. TEM specimens were either ion-milled or alternatively electropolished in a methanol-10% sulphuric acid solution at 20 V and −40°C.

The orientation relationships of nanobelt-like Si2Hf precipitates in an Al–Si–Mg–Hf alloy

2016 ◽  
Vol 49 (4) ◽  
pp. 1223-1230 ◽  
Author(s):  
Xueli Wang ◽  
Huilan Huang ◽  
Xinfu Gu ◽  
Yanjun Li ◽  
Zhihong Jia ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Coincident Site Lattice ◽  
Orthorhombic Structure ◽  
Orientation Relationships ◽  
Lattice Distribution ◽  
Site Lattice ◽  
Transmission Electron ◽  
Habit Planes ◽  
Al Matrix

The orientation relationships (ORs) between the Al matrix and Si2Hf precipitates with an orthorhombic structure in an Al–Si–Mg–Hf alloy after heat treatment at 833 K for 20 h were investigated by transmission electron microscopy and electron diffraction. Four ORs are identified as (100)Al||(010)p, (0\overline {1}1)Al||(101)pand [011]Al||[\overline {1}01]p; (11\overline {1})Al||(010)pand [011]Al||[\overline {1}01]p; (12\overline {1})Al||(010)p, (101)Al||(100)pand [1\overline {11}]Al||[001]p; (\overline {11}1)Al||(010)pand [112]Al||[\overline {1}01]p. The habit planes of these four ORs are rationalized by the fraction of good atomic matching sites at the interface. In addition, the formation of Si2Hf precipitates with a nanobelt-like morphology is interpreted on the basis of the near-coincident site lattice distribution.

Microstructure of Rapidly Solidified Cu-Fe Alloys

1983 ◽  
Vol 28 ◽  
Author(s):  
Uwe Köster ◽  
Christoph Caesar
Keyword(s):  
Cross Sections ◽  
Contact Surface ◽  
Iron Content ◽  
Melt Spinning ◽  
Volume Fraction ◽  
Thermal Contact ◽  
Lattice Parameter ◽  
Good Thermal Contact ◽  
Fe Alloys ◽  
Rapidly Solidified

ABSTRACTRapidly solidified ribbons of Cu-Fe alloys with iron contents up to 20 at.−% have been prepared by melt-spinning. Optical and electron microscopy as well as x-ray and electron diffraction techniques were used to characterize quantitatively the microstructure, i.e., grain size and shape, solubility of iron, lattice parameter, volume fraction and distribution of precipitated iron-particles, etc.Whereas the free surfaces of melt-spun Cu-Fe ribbons have been found to be very smooth, the contact surfaces usually consist of isolated areas of good thermal contact with small equiaxed grains separated by bands without contact during casting and therefore poor heat transfer. The cross sections of the ribbons generally exhibit a strong anisotropy in their microstructure: very fine crystals adjacent to the contact surface develop into narrow columnar grains, generally significantly elongated and extending across the whole section. The average columnar width of the grains has been found to decrease significantly with increasing iron content. Precipitation of iron not only depends on the iron content but also on the distance from the contact surface.

Study of Corrosion Behavior of Conventional and Nanostructured WC-Co HVOF Sprayed Coats

2010 ◽  
Vol 64 ◽  
pp. 13-18 ◽  
Author(s):  
Shahin Khameneh Asl ◽  
Mohammad Reza Saghi Beyragh ◽  
Mahdi Ghassemi Kakroudi
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Heat Treating ◽  
Crystalline Phases ◽  
Chemical Test ◽  
Transmission Electron ◽  
Hvof Spray ◽  
Wear And Corrosion Resistance

Interest in nanomaterials has increased in recent years. This is due to the potential of size reduction to nanometric scale to provide properties of materials such as hardness, toughness, wear, and corrosion resistance. The current study is focused on WC-Co cermet coats, materials that are extensively used in applications requiring wear resistance. In this work, WC-17Co powder was thermally sprayed onto mild steel using High Velocity Oxy Fuel (HVOF) spray technique. The nanostructured specimen was produced from sprayed sample by heat-treating at 1100°C in a vacuum chamber. Their structures were studied by using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Polarization and electrochemical impedance spectroscopy (EIS) tests were performed on the both types of coated samples in 3.5% NaCl solution. The amorphous phase in WC-17Co coating was transformed to crystalline phases by heat treatment at high temperatures. The heat treatment of these coatings at high temperature also resulted in partially dissolution of WC particles and formation of new crystalline phases. Generation of these phases produced the nanostructured coating with better mechanical properties. Comparative electro chemical test results showed that, the heat treatment could improve corrosion resistance of the nanostructured WC-17Co coat than the as sprayed coats.

Sign in / Sign up

Export Citation Format

Share Document