Microstructures of Rapidly Solidified Aluminum Alloys

1983 ◽  
Vol 28 ◽  
Author(s):  
J.W. Zindel ◽  
J.T. Stanley ◽  
R.D. Field ◽  
H.L. Fraser
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Aluminum Alloys ◽  
Melt Spinning ◽  
Metastable Phase ◽  
Laser Surface ◽  
Metastable Phase Diagram ◽  
Transmission Electron ◽  
Ternary Additions ◽  
Rapidly Solidified

ABSTRACTAn investigation was performed to study the origin and stability of microstructures in rapidly solidified aluminum alloys. Al-Ni and Al-Fe base alloys were rapidly solidified by means of laser surface melting and melt spinning techniques. Microstructures were studied using optical and transmission electron microscopy. The effect of microstructure on mechanical properties was also studied using microhardness measurements. The origin of the observed microstructural constituents will be explained in terms of features of the metastable phase diagram. The effect of ternary additions on stability will also be considered.

Metastable Phases in Rapidly Solidified Aluminum-Rich Al-Fe Alloys

1982 ◽  
Vol 19 ◽  
Author(s):  
D. Shechtman ◽  
L.J. Swartzendruber
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Melt Spinning ◽  
Gamma Ray ◽  
Resonance Spectrum ◽  
Metastable Phase ◽  
Metastable Phases ◽  
Transmission Electron ◽  
Fe Alloys ◽  
Rapidly Solidified

ABSTRACTAluminum-rich Al-Fe binary alloys up to and including Al3Fe were prepared by melt spinning in order to study the metastable phase structure and its transformation following heat treatment. Transmission electron microscopy and nuclear gamma-ray resonance were utilized in the study. The rapidly solidified structure was found to contain up to three metastable phases. One of the phases, with a composition and a gamma-ray resonance spectrum appropriate for Al6Fe, has either a globular or a cellular morphology upon quenching.

TEM/STEM Characterization of Rapidly Solidified Aluminum Alloys

1985 ◽  
Vol 43 ◽  
pp. 30-31
Author(s):  
R. J. Kar ◽  
T. P. McHale ◽  
R. T. Kessler
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Aluminum Alloys ◽  
High Strength ◽  
Advanced Materials ◽  
Structure Property ◽  
Aerospace Applications ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Rapidly Solidified

Low-density and high strength-type rapidly solidified (RST) aluminum alloys offer promise for structural aerospace applications. At Northrop, as part of a continuing program to establish structure-property relationships in advanced materials, detailed transmission electron microscopy (TEM)/scanning transmission electron microscopy (STEM) of candidate RST aluminum-lithium (Al-Li) and high strength (7XXX-type) aluminum-copper-magnesium-zinc (Al-Cu-Mg-Zn) alloys is routinely performed. This paper describes typical microstructural features that we have observed in these alloys.Figure 1 illustrates the microstructure of an inert-gas atomized RST Al-Li-Cu-Mg-Zr alloy. Frequently the grain boundaries are decorated with continuous or semi-continuous stringers of oxide that are relatively opaque to the incident electron beam. These have been identified to be Al-,Mg-, and Li- containing oxides present on powder particle surfaces prior to consolidation, and which have not been adequately broken up and dispersed by post-consolidation processing. The microstructures of these alloys are generally characterized by unrecystallized grains and equiaxed sub-grains pinned by fine (0.2μm) precipitates. These have been identified to be Al3Zr dispersoids using a combination of selected area diffraction/energy-dispersive x-ray (SAD/EDX) methods.

scholarly journals Mechanical properties of Ni-Fe-Cu-P-B alloy produced by two component melt spinning (TCMS)

2017 ◽  
Vol 62 (1) ◽  
pp. 137-140
Author(s):  
M. Wojciechowska ◽  
K. Ziewiec ◽  
S. Kąc ◽  
K. Prusik
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Tensile Testing ◽  
Melt Spinning ◽  
Single Phase ◽  
Energy Dispersive Spectrometry ◽  
Young Modulus ◽  
Transmission Electron ◽  
Two Component ◽  
Melt Spun

Abstract The aim of this work was to investigate the microstructure and mechanical properties of the two-component melt-spun (TCMS) alloy produced from Ni40Fe40B20 and Ni70Cu10P20 melts. The Ni40Fe40B20, Ni70Cu10P20, Ni55Fe20Cu5P10B10 alloys were arc-melted. Then the alloys were melt-spun in the two different ways i.e.: by casting from a single-chamber crucible and from the two-chamber crucible. All of the above mentioned alloys were processed in the first way and the Ni40Fe40B20 and Ni70Cu10P20 were simultaneously cast on the copper roller from the two-chamber crucible. The microstructure of the alloy was studied using transmission electron microscopy (TEM), scanning electron microscopy (SEM) with energy dispersive spectrometry (EDS) and light microscopy. The mechanical properties were investigated using tensile testing and nanoindentation. The two-component melt-spun (TCMS) amorphous Ni55Fe20Cu5P10B10 alloy present hardness, tensile strength and Young modulus on the significantly higher level than for a single phase amorphous Ni55Fe20Cu5P10B10 alloy and slightly below the corresponding values for the Ni40Fe40B20.

scholarly journals Structure of Rapidly Solidified Al-Fe-Cr-Ce Alloy

2011 ◽  
Vol 465 ◽  
pp. 199-202 ◽  
Author(s):  
Alena Michalcová ◽  
Dalibor Vojtěch ◽  
Pavel Novák ◽  
Ivan Procházka ◽  
Jakub Čížek ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Transmission Electron Microscopy ◽  
Positron Annihilation ◽  
Melt Spinning ◽  
Positron Annihilation Spectroscopy ◽  
Transmission Electron ◽  
Rapidly Solidified ◽  
Thermal Stability Of

An alloy containing Al – 3wt.% Cr – 3wt.% Fe – 0.8wt. % Ce, was prepared by melt spinning. Structure of obtained ribbons was observed by light, scanning and transmission electron microscopy. It was found out that the structure is very fine. Microhardness of cross sectioned ribbons was also measured. Defects in structure were determined by positron annihilation spectroscopy. The thermal stability of the alloy was observed by comparing rapidly solidified ribbons and ribbons annealed at 400°C and at 500°C for 100 h

Phase Transformations in Ti-7w/oMo-3w/oMe Alloy

1974 ◽  
Vol 32 ◽  
pp. 514-515
Author(s):  
S. Fujishiro
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Transmission Electron Microscopy ◽  
Tensile Strength ◽  
Mechanical Processing ◽  
Ray Method ◽  
X Ray ◽  
Transmission Electron ◽  
Water Quench ◽  
Alpha Beta

The mechanical properties of three titanium alloys (Ti-7Mo-3Al, Ti-7Mo- 3Cu and Ti-7Mo-3Ta) were evaluated as function of: 1) Solutionizing in the beta field and aging, 2) Thermal Mechanical Processing in the beta field and aging, 3) Solutionizing in the alpha + beta field and aging. The samples were isothermally aged in the temperature range 300° to 700*C for 4 to 24 hours, followed by a water quench. Transmission electron microscopy and X-ray method were used to identify the phase formed. All three alloys solutionized at 1050°C (beta field) transformed to martensitic alpha (alpha prime) upon being water quenched. Despite this heavily strained alpha prime, which is characterized by microtwins the tensile strength of the as-quenched alloys is relatively low and the elongation is as high as 30%.

Devitrification products of rapidly solidified Ni-Nb amorphous alloys.

1990 ◽  
Vol 48 (4) ◽  
pp. 950-951
Author(s):  
G. A. Bertero ◽  
W.H. Hofmeister ◽  
N.D. Evans ◽  
J.E. Wittig ◽  
R.J. Bayuzick
Keyword(s):  
Electron Microscopy ◽  
Amorphous Structure ◽  
Sulphuric Acid Solution ◽  
X Ray Diffraction ◽  
High Fracture ◽  
Transmission Electron ◽  
Xrd Techniques ◽  
Rapidly Solidified ◽  
Electromagnetically Levitated

Rapid solidification of Ni-Nb alloys promotes the formation of amorphous structure. Preliminary results indicate promising elastic properties and high fracture strength for the metallic glass. Knowledge of the thermal stability of the amorphus alloy and the changes in properties with temperature is therefore of prime importance. In this work rapidly solidified Ni-Nb alloys were analyzed with transmission electron microscopy (TEM) during in-situ heating experiments and after isothermal annealing of bulk samples. Differential thermal analysis (DTA), scanning electron microscopy (SEM) and x-ray diffraction (XRD) techniques were also used to characterize both the solidification and devitrification sequences.Samples of Ni-44 at.% Nb were electromagnetically levitated, melted, and rapidly solidified by splatquenching between two copper chill plates. The resulting samples were 100 to 200 μm thick discs of 2 to 3 cm diameter. TEM specimens were either ion-milled or alternatively electropolished in a methanol-10% sulphuric acid solution at 20 V and −40°C.

An analysis of the transport properties and mechanical stability of rapidly solidified Al-Sb alloy

2015 ◽  
Vol 10 (2) ◽  
pp. 2663-2681
Author(s):  
Rizk El- Sayed ◽  
Mustafa Kamal ◽  
Abu-Bakr El-Bediwi ◽  
Qutaiba Rasheed Solaiman
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Melt Spinning ◽  
Elastic Moduli ◽  
Mechanical Stability ◽  
Microstructural Analysis ◽  
Alloy System ◽  
Antimony Content ◽  
The Stability ◽  
Rapidly Solidified

The structure of a series of AlSb alloys prepared by melt spinning have been studied in the as melt–spun ribbons  as a function of antimony content .The stability  of these structures has  been  related to that of the transport and mechanical properties of the alloy ribbons. Microstructural analysis was performed and it was found that only Al and AlSb phases formed for different composition.  The electrical, thermal and the stability of the mechanical properties are related indirectly through the influence of the antimony content. The results are interpreted in terms of the phase change occurring to alloy system. Electrical resistivity, thermal conductivity, elastic moduli and the values of microhardness are found to be more sensitive than the internal friction to the phase changes. 

Microstructure Evolution and Mechanical Properties of an Al-Cu-Mg Alloy at Elevated Temperature

2014 ◽  
Vol 1004-1005 ◽  
pp. 148-153
Author(s):  
Min Hao ◽  
Ji Gang Ru ◽  
Ming Liu ◽  
Kun Zhang ◽  
Liang Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Elevated Temperature ◽  
Elevated Temperatures ◽  
Shear Fracture ◽  
S Phase ◽  
Mg Alloy ◽  
Transmission Electron ◽  
Fracture Features ◽  
Scanning Electron

Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were utilized to study the microstructure and mechanical behavior of an Al-Cu-Mg alloy after tensile test at 125°C, 150°C, 175°C and 200 °C, respectively. The yield strength and ultimate tensile strength decreased with the increase of temperature, while the elongation increased firstly and then decreased. The S and S′ precipitate after tension at elevated temperatures. When the temperature was higher than 175°C, the precipitate coarsens rapidly. The alloys displayed a shear fracture features at elevated temperature. The larger S′ and S phase coarsened and dropped which forming crack in the grain boundaries and precipitate interfaces, resulting in the decrease of the elongation of the alloy.

Sign in / Sign up

Export Citation Format

Share Document