Sb-Te Phase-change Nanowires by Templated Electrodeposition

2012 ◽  
Vol 1431 ◽  
Author(s):  
C. A. Ihalawela ◽  
R. E. Cook ◽  
X. M. Lin ◽  
H. H. Wang ◽  
G. Chen
Keyword(s):  
Phase Change ◽  
Dominant Role ◽  
Pulse Excitation ◽  
Aao Template ◽  
X Ray ◽  
High Data ◽  
Aspect Ratios ◽  
Composition And Structure ◽  
Future Challenges ◽  
Non Volatile Memory

ABSTRACTPhase-change memory materials (PCMMs) are semiconductors that exhibit rapid order-disorder transition under electrical or optical pulse excitation. Currently thin-film-based PCMMs play a dominant role in fabrication of non-volatile memory devices. In contrast, phase-change nanowires (PCNWs) have the potential to overcome future challenges such as high data density and low power consumption. Among the various methods to synthesize PCNWs, the vapor-liquid-solid method has been reported previously. In this paper, we report synthesis of Sb-Te PCNWs using a templated electrochemical method. Nanoporous anodic aluminum oxide (AAO) was used as a template for the growth of nanowires. Sb-Te PCNWs with different compositions, diameters and aspect ratios were grown inside the AAO template by electrodeposition. Composition and structure of these nanowires were characterized by energy dispersive X-ray spectroscopy, X-ray diffraction, and scanning and transmission electron microscopy. It is found that electrodeposition through nanosized channels results in materials that are quite different from those electrodeposited on unrestricted surface. The mechanism of nanowire formation inside the channels of AAO template is discussed.

scholarly journals Preparation of Porous Hydroxyapatite Using Cetyl Trimethyl Ammonium Bromide as Surfactant for the Removal of Lead Ions from Aquatic Solutions

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1617
Author(s):  
Silviu-Adrian Predoi ◽  
Carmen Steluta Ciobanu ◽  
Mikael Motelica-Heino ◽  
Mariana Carmen Chifiriuc ◽  
Monica Luminita Badea ◽  
...  
Keyword(s):  
Cetyl Trimethyl Ammonium Bromide ◽  
Morphological Changes ◽  
Low Cost ◽  
Lead Ions ◽  
Ammonium Bromide ◽  
Porous Hydroxyapatite ◽  
X Ray ◽  
Composition And Structure ◽  
Cetyl Trimethyl Ammonium ◽  
Co Precipitation

In the present study, a new low-cost bioceramic nanocomposite based on porous hydroxyapatite (HAp) and cetyl trimethyl ammonium bromide (CTAB) as surfactant was successfully obtained by a simple chemical co-precipitation. The composition and structure of the HAp-CTAB were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, transmission electron microscopy (TEM), scanning electron microscope (SEM) equipped with an energy dispersive X-ray (EDX) spectrometer, and N2 adsorption/desorption analysis. The capacity of HAp-CTAB nanocomposites to remove the lead ions from aqueous solutions was studied by adsorption batch experiments and proved by Langmuir and Freundlich models. The Pb2+ removal efficiency of HAp-CTAB biocomposite was also confirmed by non-destructive ultrasound studies. The cytotoxicity assays showed that the HAp-CTAB nanocomposites did not induce any significant morphological changes of HeLa cells after 24 h of incubation or other toxic effects. Taken together, our results suggests that the obtained porous HAp-CTAB powder could be used for the decontamination of water polluted with heavy metals, such as Pb2+.

scholarly journals pH-controlled synthesis of sustainable lauric acid/SiO2 phase change material for scalable thermal energy storage

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shafiq Ishak ◽  
Soumen Mandal ◽  
Han-Seung Lee ◽  
Jitendra Kumar Singh
Keyword(s):  
Electron Microscopy ◽  
Phase Change ◽  
Lauric Acid ◽  
Photoelectron Spectroscopy ◽  
Phase Change Materials ◽  
Precursor Solution ◽  
Thermal Reliability ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Heating And Cooling

AbstractLauric acid (LA) has been recommended as economic, eco-friendly, and commercially viable materials to be used as phase change materials (PCMs). Nevertheless, there is lack of optimized parameters to produce microencapsulated PCMs with good performance. In this study, different amounts of LA have been chosen as core materials while tetraethyl orthosilicate (TEOS) as the precursor solution to form silicon dioxide (SiO2) shell. The pH of precursor solution was kept at 2.5 for all composition of microencapsulated LA. The synthesized microencapsulated LA/SiO2 has been characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS), Scanning electron microscopy (SEM), and Transmission electron microscopy (TEM). The SEM and TEM confirm the microencapsulation of LA with SiO2. Thermogravimetric analysis (TGA) revealed better thermal stability of microencapsulated LA/SiO2 compared to pure LA. PCM with 50% LA i.e. LAPC-6 exhibited the highest encapsulation efficiency (96.50%) and encapsulation ratio (96.15%) through Differential scanning calorimetry (DSC) as well as good thermal reliability even after 30th cycle of heating and cooling process.

scholarly journals Controlling water evaporation through self-assembly

2016 ◽  
Vol 113 (37) ◽  
pp. 10275-10280 ◽  
Author(s):  
Kevin Roger ◽  
Marianne Liebi ◽  
Jimmy Heimdal ◽  
Quoc Dat Pham ◽  
Emma Sparr
Keyword(s):  
Self Assembly ◽  
Feedback Loop ◽  
Ambient Air ◽  
Underlying Mechanism ◽  
Water Evaporation ◽  
Air Humidity ◽  
X Ray ◽  
X Ray Scattering ◽  
Composition And Structure ◽  
Living Organisms

Water evaporation concerns all land-living organisms, as ambient air is dryer than their corresponding equilibrium humidity. Contrarily to plants, mammals are covered with a skin that not only hinders evaporation but also maintains its rate at a nearly constant value, independently of air humidity. Here, we show that simple amphiphiles/water systems reproduce this behavior, which suggests a common underlying mechanism originating from responding self-assembly structures. The composition and structure gradients arising from the evaporation process were characterized using optical microscopy, infrared microscopy, and small-angle X-ray scattering. We observed a thin and dry outer phase that responds to changes in air humidity by increasing its thickness as the air becomes dryer, which decreases its permeability to water, thus counterbalancing the increase in the evaporation driving force. This thin and dry outer phase therefore shields the systems from humidity variations. Such a feedback loop achieves a homeostatic regulation of water evaporation.

ROOM TEMPERATURE PHOTOLUMINESCENCE OF POLYCRYSTALLINE SIC PREPARED FROM CARBON-SATURATED SI MELT

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1047-1051
Author(s):  
JIANPING MA ◽  
ZHIMING CHEN ◽  
GANG LU ◽  
MINGBIN YU ◽  
LIANMAO HANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Uv Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Composition And Structure ◽  
Light Excitation ◽  
Scanning Electron

Intense photoluminescence (PL) has been observed at room temperature from the polycrystalline SiC samples prepared from carbon-saturated Si melt at a temperature ranging from 1500 to 1650°C. Composition and structure of the samples have been confirmed by means of X-ray photoelectron spectroscopy, X-ray diffraction and scanning electron microscopy. PL measurements with 325 nm UV light excitation revealed that the room temperature PL spectrum of the samples consists of 3 luminescent bands, the peak energies of which are 2.38 eV, 2.77 eV and 3.06 eV, respectively. The 2.38 eV band is much stronger than the others. It is suggested that some extrinsic PL mechanisms associated with defect or interface states would be responsible to the intensive PL observed at room temperature.

Lateral Size of Self-Patterned Nanostructures Controlled by Multi-Step Deposition

2005 ◽  
Vol 106 ◽  
pp. 117-122 ◽  
Author(s):  
Izabela Szafraniak ◽  
Dietrich Hesse ◽  
Marin Alexe
Keyword(s):  
Electron Microscopy ◽  
Ultrathin Films ◽  
Lateral Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Non Volatile Memory ◽  
Ferroelectric Capacitors ◽  
Scanning Electron

Self-patterning presents an appealing alternative to lithography for the production of arrays of nanoscale ferroelectric capacitors for use in high density non-volatile memory devices. Recently a self-patterning method, based on the use of the instability of ultrathin films during hightemperature treatments, was used to fabricate nanosized ferroelectrics. This paper reports the use of the method for the preparation of PZT nanoislands on different single crystalline substrates - SrTiO3, MgO and LaAlO3. Moreover, a multi-step deposition procedure in order to control lateral the dimension of the crystals was introduced. The nanostructures obtained were studied by atomic force microscopy, scanning electron microscopy and X-ray diffraction.

scholarly journals The Influence of Scandium on the Composition and Structure of the Ti-Al Alloy Obtained by “Hydride Technology”

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 918
Author(s):  
Natalia Karakchieva ◽  
Olga Lepakova ◽  
Yuri Abzaev ◽  
Victor Sachkov ◽  
Irina Kurzina
Keyword(s):  
Rietveld Method ◽  
Al Alloy ◽  
Surface Strength ◽  
Average Width ◽  
Near Surface ◽  
X Ray ◽  
Lamellar Structures ◽  
Quantitative Content ◽  
Transmission Electron ◽  
Composition And Structure

In this study the influence of scandium on the structural and phase state of the Ti-Al alloy obtained by the method of “Hydride Technology” (HT). The Rietveld method has allowed for determining the content of basic phases of the 49at.%Ti-49at.%Al-2at.%Sc system. By means of the methods of transmission electron microscopy (TEM) and X-ray spectral microanalysis, it has been established that scandium additives into the Ti-Al system result in the change of the quantitative content of phases in local regions of the structure. The Ti2Al5 phase has been found, and Ti2Al has been absent. In the morphology of substructures Ti-Al and Ti-Al-Sc there are lamellar structures or lamellae; the peculiarities of the distribution, fraction and size of which are influenced by scandium additives. The average width of Al-rich lamellae has been 0.85 µm, which is four times greater than that for the Ti-Al system (0.21 µm). For Ti-rich lamellae of the sample of the Ti-Al-Sc alloy, the average width of the lamellae has been 0.54 µm, and for Ti-Al it has been 0.34 µm. Based on the obtained data, a scheme of the distribution of phases in the composition of the Ti-Al-Sc alloy in the lamellar structures has been proposed. It has been established that in the Ti-Al-Sc system there is growth of the near-surface strength relative to Ti-Al. In this way, the microhardness of the Ti-Al-Sc alloy has amounted to 1.7 GPa, that is of the Ti-Al alloy which is 1.2 GPa.

LiMn2-xCuxO4 Spineis - 5 V Cathode Materials

1997 ◽  
Vol 496 ◽  
Author(s):  
Yair Ein-Eli ◽  
W. F. Howard ◽  
Sharon H. Lu ◽  
Sanjeev Mukerjee ◽  
James McBreen ◽  
...  
Keyword(s):  
Copper Ions ◽  
Oxide Phase ◽  
Electrochemical Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Spinel Compounds ◽  
Composition And Structure ◽  
Phase Spinel ◽  
Lithium Copper Oxide ◽  
X Ray Absorption

ABSTRACTA series of electroactive spinel compounds, LiMn2-xCuxO4 (0.1 ≤ x ≤ 0.5) has been studied by crystallographic, spectroscopie and electrochemical methods and by electron-microscopy. These LiMn2-xCuxO4 spinels are nearly identical in structure to cubic LiMn2O4 and successfully undergo reversible Li intercalation. The electrochemical data show slight shifts to higher voltage for the delithiation reaction that normally occurs at 4.1 V in standard Li1−xMn2O4 electrodes (1 ≥ x ≥ 0) corresponding to the oxidation of Mn3+ to Mn4+. The data also show a remarkable reversible electrochemical process at 4.9 V which is attributed to the oxidation of Cu2+ to Cu3+. The inclusion of Cu in the spinel structure enhances the electrochemical stability of these materials upon cycling. The initial capacity of LiMn2-xCuxO4 spinels decreases with increasing x from 130 mAh/g in LiMn2O4 (x=0) to 70 mAh/g in “LiMn1.5Cu0.5O4”(x=0.5). Although the powder X-ray diffraction pattern of “LiMn1.5Cu0.5 O4” shows a single-phase spinel product, neutron diffraction data show a small, but significant quantity of an impurity phase, the composition and structure of which could not be identified. X-ray absorption spectroscopy was used to gather information about the oxidation states of the manganese and copper ions. The composition of the spinel component in the LiMn1.5Cu0.5O4 was determined from X-ray diffraction and XANES data to be Li1.01Mn1.67Cu0.32O4 suggesting, to a best approximation, that the impurity in the sample was a lithium-copper-oxide phase.

scholarly journals All-optical dynamic tuning of local excitonic emission of monolayer MoS2 by integration with Ge2Sb2Te5

Nanophotonics ◽  
2020 ◽  
Vol 9 (8) ◽  
pp. 2351-2359
Author(s):  
Hao Ouyang ◽  
Haitao Chen ◽  
Yuxiang Tang ◽  
Jun Zhang ◽  
Chenxi Zhang ◽  
...  
Keyword(s):  
Thin Film ◽  
Phase Change ◽  
Optical Networks ◽  
Dominant Role ◽  
Laser Pulses ◽  
Coulomb Interactions ◽  
Optical Modulators ◽  
Dynamic Tuning ◽  
All Optical ◽  
Excitonic Emission

AbstractStrong quantum confinement and coulomb interactions induce tightly bound quasiparticles such as excitons and trions in an atomically thin layer of transitional metal dichalcogenides (TMDs), which play a dominant role in determining their intriguing optoelectronic properties. Thus, controlling the excitonic properties is essential for the applications of TMD-based devices. Here, we demonstrate the all-optical tuning of the local excitonic emission from a monolayer MoS2 hybridized with phase-change material Ge2Sb2Te5 (GST) thin film. By applying pulsed laser with different power on the MoS2/GST heterostructure, the peak energies of the excitonic emission of MoS2 can be tuned up to 40 meV, and the exciton/trion intensity ratio can be tuned by at least one order of magnitude. Raman spectra and transient pump-probe measurements show that the tunability originated from the laser-induced phase change of the GST thin film with charge transferring from GST to the monolayer MoS2. The dynamic tuning of the excitonic emission was all done with localized laser pulses and could be scaled readily, which pave a new way of controlling the excitonic emission in TMDs. Our findings could be potentially used as all-optical modulators or switches in future optical networks.

scholarly journals Direct Numerical Simulation of Pore-Scale Trapping Events During Capillary-Dominated Two-Phase Flow in Porous Media

2021 ◽  
Author(s):  
Mosayeb Shams ◽  
Kamaljit Singh ◽  
Branko Bijeljic ◽  
Martin J. Blunt
Keyword(s):  
Numerical Simulation ◽  
Porous Media ◽  
Direct Numerical Simulation ◽  
Complex Geometry ◽  
Flow In Porous Media ◽  
Pore Scale ◽  
Contact Lines ◽  
Two Phase ◽  
X Ray ◽  
Aspect Ratios

AbstractThis study focuses on direct numerical simulation of imbibition, displacement of the non-wetting phase by the wetting phase, through water-wet carbonate rocks. We simulate multiphase flow in a limestone and compare our results with high-resolution synchrotron X-ray images of displacement previously published in the literature by Singh et al. (Sci Rep 7:5192, 2017). We use the results to interpret the observed displacement events that cannot be described using conventional metrics such as pore-to-throat aspect ratio. We show that the complex geometry of porous media can dictate a curvature balance that prevents snap-off from happening in spite of favourable large aspect ratios. We also show that pinned fluid-fluid-solid contact lines can lead to snap-off of small ganglia on pore walls; we propose that this pinning is caused by sub-resolution roughness on scales of less than a micron. Our numerical results show that even in water-wet porous media, we need to allow pinned contacts in place to reproduce experimental results.

Template Synthesis of Indium Nanowires Using Anodic Aluminum Oxide Membranes

2008 ◽  
Vol 8 (9) ◽  
pp. 4488-4493 ◽  
Author(s):  
Feng Chen ◽  
Adrian H. Kitai
Keyword(s):  
Aluminum Oxide ◽  
Template Synthesis ◽  
Anodic Aluminum Oxide ◽  
Preferred Orientation ◽  
Hydraulic Pressure ◽  
X Ray Diffraction ◽  
Aao Template ◽  
X Ray ◽  
Anodic Aluminum ◽  
Oxide Membranes

Indium nanowires with diameters approximately 300 nm have been synthesized by a hydraulic pressure technique using anodic aluminum oxide (AAO) templates. The indium melt is injected into the AAO template and solidified to form nanostructures. The nanowires are dense, continuous and uniformly run through the entire ∼60 μm thickness of the AAO template. X-ray diffraction (XRD) reveals that the nanowires are polycrystalline with a preferred orientation. SEM is performed to characterize the morphology of the nanowires.

Sign in / Sign up

Export Citation Format

Share Document