Fabrication of Device-grade Separation-by-implantation-of-oxygen Materials by Optimizing Dose-energy Match

2002 ◽  
Vol 17 (7) ◽  
pp. 1634-1643 ◽  
Author(s):  
Meng Chen ◽  
Yuehui Yu ◽  
Xi Wang ◽  
Xiang Wang ◽  
Jing Chen ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Silicon On Insulator ◽  
Optimum Dose ◽  
Cross Sectional ◽  
Buried Oxide ◽  
Transmission Electron ◽  
Good Crystallinity ◽  
Grade Separation ◽  
Silicon Islands

In this article, we report formation of separation-by-implantation-of-oxygen (SIMOX) silicon-on-insulator (SOI) materials with doses ranging from (2.5 to 13.5) × 1017 cm−2 at acceleration energies of 70–160 keV and subsequent annealing at temperatures over 1300 °C in oxygen + argon atmosphere for 5 h. The microstructure evolution of SIMOX wafers was characterized by Rutherford backscattering spectroscopy, cross-sectional transmission electron microscopy, high-resolution transmission electron microscopy, Secco, and Cu-plating. This study revealed a series of good matches of dose-energy combination at acceleration energies of 70–160 keV with doses of (2.5–5.5) × 1017 cm−2, in which SIMOX wafers had good crystallinity of the top silicon, sharp Si/SiO2 interfaces, high-integrity buried oxide layers with low pinhole density, and low detectable silicon islands. Furthermore, the higher the oxygen dose, the higher the implanted energy required for the formation of a buried oxide free from Si islands. The mechanism of the optimum dose-energy match is discussed.

scholarly journals Formation of Buried Oxide in Mev Oxygen Implanted Silicon

1987 ◽  
Vol 107 ◽  
Author(s):  
C.W. Nieh ◽  
F. Xiong ◽  
C. C. Ahn ◽  
Z. Zhou ◽  
D. N. Jamieson ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Resolution Electron Microscopy ◽  
Chemical Information ◽  
Cross Sectional ◽  
Buried Oxide ◽  
Implantation Temperature ◽  
Transmission Electron ◽  
Resolution Electron ◽  
Electron Energy Loss

AbstractWe have studied the formation of buried oxide in MeV oxygen implanted Si. A continuous oxide layer is formed in the samples implanted with 2x1018/cm2 oxygen and annealed at 1300° C. The microstructures are studied by cross-sectional transmission electron microscopy and high resolution electron microscopy. Chemical information was obtained by electron energy loss spectroscopy. The effects of implantation temperature are studied. Implantation at a low substrate temperature leads to a well-defined buried SiO2 layer, inhibits the formation of oxide precipitates in the silicon, and reduces silicon inclusions in the SiO2.

Buried oxide layers formed by low-dose oxygen implantation

1992 ◽  
Vol 7 (4) ◽  
pp. 788-790 ◽  
Author(s):  
S. Nakashima ◽  
K. Izumi
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Breakdown Voltage ◽  
Low Dose ◽  
Annealing Temperature ◽  
Cross Sectional ◽  
Oxide Layers ◽  
Buried Oxide ◽  
Transmission Electron ◽  
Anneal Temperature

The structure of buried oxide layers formed by low-dose 16O+ implantation of 0.4 and 0.7 × 1018 cm−2 at 180 keV and by subsequent annealing in the temperature range of 1150 to 1350 °C has been investigated using cross-sectional transmission electron microscopy (XTEM). At a dose of 0.4 × 1018 cm−2, an 80-nm continuous uniform buried oxide layer having a breakdown voltage of approximately 40 V is formed after annealing at 1350 °C. At a dose of 0.7 × 1018 cm−2, multiple buried oxide layers having Si islands between them are formed at an anneal temperature of 1150 °C. The number of multiple layers is reduced as the annealing temperature increases, but the Si islands do not dissolve even after annealing at 1350 °C. The existence of the Si islands causes the breakdown voltage to fall to 0 V despite the higher dose.

Microstructure of laser-irradiated, conducting Kapton polyimide

1995 ◽  
Vol 53 ◽  
pp. 502-503
Author(s):  
D. L. Callahan ◽  
Z. Ball ◽  
H. M. Phillips ◽  
R. Sauerbrey
Keyword(s):  
Electron Microscopy ◽  
Phase Transition ◽  
Transmission Electron Microscopy ◽  
Cross Section ◽  
Film Surface ◽  
Cross Sectional ◽  
General Utility ◽  
Transmission Electron ◽  
Considerable Debate ◽  
Potential Applications

Ultraviolet laser-irradiation can be used to induce an insulator-to-conductor phase transition on the surface of Kapton polyimide. Such structures have potential applications as resistors or conductors for VLSI applications as well as general utility electrodes. Although the percolative nature of the phase transformation has been well-established, there has been little definitive work on the mechanism or extent of transformation. In particular, there has been considerable debate about whether or not the transition is primarily photothermal in nature, as we propose, or photochemical. In this study, cross-sectional optical microscopy and transmission electron microscopy are utilized to characterize the nature of microstructural changes associated with the laser-induced pyrolysis of polyimide.Laser-modified polyimide samples initially 12 μm thick were prepared in cross-section by standard ultramicrotomy. Resulting contraction in parallel to the film surface has led to distortions in apparent magnification. The scale bars shown are calibrated for the direction normal to the film surface only.

Ion thinning of integrated circuit transverse specimens for transmission electron microscopy

1992 ◽  
Vol 50 (2) ◽  
pp. 1426-1427
Author(s):  
F. Shaapur
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Integrated Circuit ◽  
Substrate Surface ◽  
Homogeneous Material ◽  
Material System ◽  
Ion Milling ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Motion Profile

Non-uniform ion-thinning of heterogenous material structures has constituted a fundamental difficulty in preparation of specimens for transmission electron microscopy (TEM). A variety of corrective procedures have been developed and reported for reducing or eliminating the effect. Some of these techniques are applicable to any non-homogeneous material system and others only to unidirectionalfy heterogeneous samples. Recently, a procedure of the latter type has been developed which is mainly based on a new motion profile for the specimen rotation during ion-milling. This motion profile consists of reversing partial revolutions (RPR) within a fixed sector which is centered around a direction perpendicular to the specimen heterogeneity axis. The ion-milling results obtained through this technique, as studied on a number of thin film cross-sectional TEM (XTEM) specimens, have proved to be superior to those produced via other procedures.XTEM specimens from integrated circuit (IC) devices essentially form a complex unidirectional nonhomogeneous structure. The presence of a variety of mostly lateral features at different levels along the substrate surface (consisting of conductors, semiconductors, and insulators) generally cause non-uniform results if ion-thinned conventionally.

TEM Sample Preparation Tricks for Advanced DRAMs

2015 ◽  
Author(s):  
Ching Shan Sung ◽  
Hsiu Ting Lee ◽  
Jian Shing Luo
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Tem Analysis ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Characterization Of Materials

Abstract Transmission electron microscopy (TEM) plays an important role in the structural analysis and characterization of materials for process evaluation and failure analysis in the integrated circuit (IC) industry as device shrinkage continues. It is well known that a high quality TEM sample is one of the keys which enables to facilitate successful TEM analysis. This paper demonstrates a few examples to show the tricks on positioning, protection deposition, sample dicing, and focused ion beam milling of the TEM sample preparation for advanced DRAMs. The micro-structures of the devices and samples architectures were observed by using cross sectional transmission electron microscopy, scanning electron microscopy, and optical microscopy. Following these tricks can help readers to prepare TEM samples with higher quality and efficiency.

Post Oxidation Anneal and Re-Oxidation Effects in 5 nm SiO2 Films

1986 ◽  
Vol 76 ◽  
Author(s):  
L. Dori ◽  
M. Arienzo ◽  
Y. C. Sun ◽  
T. N. Nguyen ◽  
J. Wetzel
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Silicon Dioxide ◽  
Oxygen Vacancies ◽  
Interface Roughness ◽  
Cross Sectional ◽  
Oxide Charge ◽  
Transmission Electron ◽  
Redistribution Of Hydrogen ◽  
Transmission Electron Microscopy Cross

ABSTRACTUltrathin silicon dioxide films, 5 nm thick, were grown in a double-walled furnace at 850°C in dry O2. A consistent improvement in the electrical properties is observed following the oxidation either with a Post-Oxidation Anneal (POA) at 1000°C in N2 or with the same POA followed by a short re-oxidation (Re-Ox) step in which 1 nm of additional oxide was grown. We attribute these results to the redistribution of hydrogen and water related groups as well as to a change in the concentration of sub-oxide charge states at the Si-SiO2 interface. A further improvement observed after the short re-oxidation step had been attributed to the filling of the oxygen vacancies produced during the POA. High resolution Transmission Electron Microscopy cross-sectional observations of the Si-iSO2 interface have evidenced an increase in the interface roughness after the thermal treatment at high temperature. These results are in agreement with recent XPS data.

Sign in / Sign up

Export Citation Format

Share Document