Three-Point Bending Fracture Behavior of Cracked Giant Magnetostrictive Materials Under Magnetic Fields

2015 ◽  
Vol 44 (4) ◽  
pp. 20140439 ◽  
Author(s):  
Fumio Narita ◽  
Koji Shikanai ◽  
Yasuhide Shindo ◽  
Kotaro Mori
Keyword(s):  
Magnetic Fields ◽  
Fracture Behavior ◽  
Three Point Bending ◽  
Magnetostrictive Materials ◽  
Giant Magnetostrictive Materials ◽  
Bending Fracture

Three-point bending fatigue of cracked giant magnetostrictive materials under magnetic fields

2017 ◽  
Vol 228 (11) ◽  
pp. 3867-3876 ◽  
Author(s):  
Fumio Narita ◽  
Koji Shikanai ◽  
Yasuhide Shindo ◽  
Kotaro Mori
Keyword(s):  
Magnetic Fields ◽  
Bending Fatigue ◽  
Three Point Bending ◽  
Magnetostrictive Materials ◽  
Giant Magnetostrictive Materials

Three-Point Bending Fracture Behaviors of Bamboo

2011 ◽  
Vol 261-263 ◽  
pp. 464-468 ◽  
Author(s):  
Yuan Lin An ◽  
Zhi Ming Liu ◽  
Gan Wang ◽  
Wen Jian Wu
Keyword(s):  
Building Material ◽  
Fracture Behavior ◽  
Bending Strength ◽  
Fiber Layer ◽  
Three Point Bending ◽  
Fracture Behaviors ◽  
Bamboo Fibers ◽  
Natural Building ◽  
Bending Fracture ◽  
Fracture Processes

Bamboo is a typical natural building material, which is longitudinally reinforced by robust fibers. This present paper focuses on the three-point bending fracture behavior of bamboo across and along fiber lengths with dense fiber layer upward and downward. The three-point bending strength of bamboo across the fibers is about ten times higher than that along the bamboo fibers, and the value of three-point bending strength with dense fiber layer downward is higher than that with dense fiber layer upward. Based on the microstructure of the fracture surfaces and the loading curves, different fracture processes are concluded to explain the anisotropy of bamboo.

THE EFFECT OF HIGH TEMPERATURE CORROSION ON MECHANICAL BEHAVIOR OF A GAMMA-TiAl ALLOY

2010 ◽  
Vol 24 (15n16) ◽  
pp. 2970-2975 ◽  
Author(s):  
WENYUE ZHAO ◽  
YUE MA ◽  
SHENGKAI GONG
Keyword(s):  
High Temperature ◽  
Fracture Behavior ◽  
Tial Alloy ◽  
Crack Nucleation ◽  
High Temperature Corrosion ◽  
Bending Tests ◽  
Three Point Bending ◽  
Salt Corrosion ◽  
Corrosion Pits ◽  
Bending Fracture

The mechanical properties of Ti -48 Al -2 Cr -2 Nb alloy were discussed after the high temperature corrosion tests carried out with salt mixture of 75wt. % Na 2 SO 4 and 25wt. % NaCl at 800°C. The microstructure of the alloy after corrosion was observed by SEM and the fracture behavior of the corroded and uncorroded alloys was investigated by means of the three-point bending tests. It has been shown that the corrosion path was mainly along the lamellar structure and rough surface with a large number of corrosion pits formed during the high temperature corrosion. The experimental results also indicated that the bearing capacity of bending fracture descended evidently due to the molten salt corrosion at high temperature, which only had remarkable effects on the surface state of the alloy. The microcracks inside the alloy always propagated along the phase interfaces and grain boundaries while the corrosion pits on salt-deposited surface became the main crack initiation location in corroded alloy. The stress concentration caused by corrosion was considered as the essential reason of the property reduction, which decreased the energy barrier of crack nucleation and shortened the incubation period.

Effect of Concrete Mixture Composition on Acoustic Emission and Fracture Parameters Obtained from Three-Point Bending Test

2015 ◽  
Vol 1100 ◽  
pp. 152-155
Author(s):  
Libor Topolář ◽  
Hana Šimonová ◽  
Petr Misák
Keyword(s):  
Acoustic Emission ◽  
Bending Test ◽  
Mixture Composition ◽  
Three Point Bending ◽  
Concrete Mixtures ◽  
Fracture Parameters ◽  
Fracture Tests ◽  
Stress Behaviour ◽  
Bending Fracture ◽  
Fracture Processes

This paper reports the analysis of acoustic emission signals captured during three-point bending fracture tests of concrete specimens with different mixture composition. Acoustic emission is an experimental tool well suited for monitoring fracture processes in material. The typical acoustic emission patterns were identified in the acoustic emission records for three different concrete mixtures to further describe the under-the-stress behaviour and failure development. An understanding of microstructure–performance relationships is the key to true understanding of material behaviour. The acoustic emission results are accompanied by fracture parameters determined via evaluation of load versus deflection diagrams recorded during three-point bending fracture tests.

Statistical analysis of three-point-bending fracture failure of mortar

2021 ◽  
Vol 300 ◽  
pp. 123883
Author(s):  
Peng Zhang ◽  
Peng Yuan ◽  
Junfeng Guan ◽  
Xianhua Yao ◽  
Lielie Li
Keyword(s):  
Statistical Analysis ◽  
Three Point Bending ◽  
Fracture Failure ◽  
Bending Fracture
Sign in / Sign up

Export Citation Format

Share Document