Evaluation of glass-fiber grafted by epoxide-terminated hyperbranched polymer on the effect of mechanical characterization of epoxy composites

2018 ◽  
Vol 25 (2) ◽  
pp. 417-424 ◽  
Author(s):  
Shuiping Li ◽  
Yanbo Li ◽  
Huajun Zhu ◽  
Qing Lin ◽  
Haijun Hou ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Hyperbranched Polymer ◽  
Impact Resistance ◽  
Percentage Elongation ◽  
Elongation At Break ◽  
Flexural Tests

AbstractIn this study, glass-fiber, grafted by epoxide-terminated hyperbranched polymer (GF-HBPE), was incorporated into epoxy resins for reinforcement purpose. The effects of GF-HBPE content on mechanical properties of the resulting epoxy-based composites, such as tensile strength, percentage elongation at break, flexural strength, and impact strength, were investigated. The experimental results revealed that GF-HBPE substantially outperformed impact resistance in both tensile and flexural tests. For instance, the tensile strength, percentage elongation at break, flexural strength, and impact strength of the epoxy composite with 1 wt% GF-HBPE increase by about 23.6%, 125%, 26%, and 74.5%, respectively, compared to the unmodified epoxy thermoset.

Evaluation of morphological characteristics and mechanical performance of Rockforce mineral fiber- and glass fiber-reinforced polyamide-6 composites

2014 ◽  
Vol 21 (3) ◽  
pp. 323-328 ◽  
Author(s):  
Huseyin Unal ◽  
A. Mimaroglu
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Flexural Modulus ◽  
Morphological Characteristics ◽  
Tensile Modulus ◽  
Polyamide 6 ◽  
Uniaxial Tensile ◽  
Elongation At Break

AbstractIn this study, the effect of addition of Rockforce mineral and glass fiber fillers on the mechanical properties and morphological characteristics of polyamide-6 composites were evaluated and compared. Reinforcements, single and mixed compounds by various weight ratios between 10 and 30 wt%, were added to polyamide-6 polymer. Uniaxial tensile, Izod impact, and flexural tests were carried out. Tensile strength, elongation at break, tensile modulus, flexural strength, flexural modulus, and impact strength were obtained. The results showed that the tensile strength, tensile modulus, flexural strength, and flexural modulus of polyamide-6 composite increased with the increase in the glass fiber ratio and are slightly influenced by the addition of Rockforce mineral fibers. Moreover, the impact strength follows an increasing and decreasing profile, whereas elongation at break values decreased with the increase in reinforcement ratio. Finally, scanning electron microscopy was used for comparison and evaluation of the fracture surface of the polyamide-6 composite.

scholarly journals The Utilization of Waste Cooking Oil (WCO) as A Mixture of Polyol Sourcein. The Production of Polyurethane Using Toluene Diisocyanate

2019 ◽  
Vol 35 (1) ◽  
pp. 221-227
Author(s):  
Maulida Lubis ◽  
Mara Bangun Harahap ◽  
Iriany Iriany ◽  
Muhammad Hendra S. Ginting ◽  
Iqbal Navissyah Lazuardi ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Waste Cooking Oil ◽  
Raw Material ◽  
Toluene Diisocyanate ◽  
Elongation At Break ◽  
Cooking Oil ◽  
A Value ◽  
Stirring Time

Cooking oil waste that has been disposed could contamine the environment. However, if it is processed well, it can potentially become a raw material of polyurethane. The aim of this study was to determine the best polyurethane on the tensile strength, impact strength, elongation at break, water absorption, characterization of Fourier Transform Infra-Red (FTIR) and the characterization of Scanning Electron Microscopy (SEM). The variables used in this study were ambient process temperature with 440 rpm stirring speed, 1-minute stirring time, the ratio of polyoland WCO was 7:3 (% w/w), and the ratio of Toluene Diisocyanate (TDI) and WCO was 1:1; 1:2; 1:3; 1:4 (% w/w). The results obtained from the analysis of the best tensile strength against the polyurethane synthetic was in the 1:1 ratio of mixed variations between oil and TDI with a value of 0.403 MPa. The best impact strength was in the ratio of mixed variations between oil and TDI with 1:4 (% w/w) with a value of 600.975 J/m2. The best elongation at break against polyurethane foam synthetic was in the 1:3 ratio of mixture variations of oil and TDI with a value of 4.506%.

Direct Reactive Compatibilization of GMA on PE/Wood-Flour Composite

2011 ◽  
Vol 378-379 ◽  
pp. 735-739
Author(s):  
Yue Wen Li ◽  
Xin Hua Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Wood Flour ◽  
Reactive Extrusion ◽  
Rupture Surface ◽  
Elongation At Break ◽  
Reactive Compatibilization ◽  
Anchoring Strength

Reactive compatibilization between high-density polyethylene(HDPE) and wood-flour was achieved via direct reactive extrusion of glycidyl methacrylate(GMA), initiator, HDPE and wood-flour. Impact rupture surface of the composite was observed by scanning electron microscope(SEM), and its load deformation temperature(HDT) and mechanical properties were tested. Effect of GMA dosage and extrusion temperature on reactive compatibilization of the composite was analysed. The result indicated that the anchoring strength of interface in the composite was obviously strengthened, and its HDT, tensile strength, flexural strength, notched impact strength and elongation at break of the composite were distinctly improved due to the addition of GMA and dicumyl peroxide(DCP). When the composite was extruded at 180°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 84°C, 40Mpa, 45Mpa, 11% and 6.6KJ.m-2, which respectively increased by 17°C, 74%, 36%, 83% and 69% than that of the composite without reactive compatibilization, and when the composite was extruded at 190°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 84°C, 40Mpa, 44Mpa, 11% and 6.6KJ.m-2, which respectively increased by 20°C, 60%, 26%, 83% and 83% than that of the composite without reactive compatibilization. When GMA usage increased, the HDT and mechanical properties of the composite increased first, then descended, and the optimum usage of GMA was 1wt%-3wt%.

scholarly journals Mechanical Properties of Abaca Fiber Reinforced Urea Formaldehyde Composites

2015 ◽  
Vol 12 (1) ◽  
pp. 54-59 ◽  
Author(s):  
Abhishek Suvarna ◽  
Akash Katagi ◽  
Jackson Pasanna ◽  
Sunil Kumar ◽  
Basavaraju Bennehalli ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Urea Formaldehyde ◽  
Charpy Impact ◽  
Fiber Reinforced ◽  
Compression Moulding ◽  
Charpy Impact Strength

The present investigation focuses on the fabrication and mechanical characterization of alkali treated natural abaca fiber reinforced urea formaldehyde composites. The composites were prepared by means of compression moulding, and then the effects of fiber loading on mechanical properties such as tensile strength, flexural strength and impact strength were investigated. The composite with 40 wt% abaca fibers gave excellent tensile strength and flexural strength showing that it has the most superior bonding and adhesion of all the composites. In particular, the highest value, 10.02 kJ/m2 of charpy impact strength is observed in the composite with 50 wt% abaca fiber. This work revealed the potential of using abaca fibers in fiberboard.

Effect of wood particle size on selected properties of neat and recycled wood polypropylene composites

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 3427-3442
Author(s):  
Vedat Çavuş ◽  
Fatih Mengeloğlu
Keyword(s):  
Particle Size ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Wood Flour ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Wood Particle ◽  
Sem Analysis ◽  
Elongation At Break

Neat polypropylene (PP)- and post-industrial recycled polypropylene (rPP)-based wood-plastic composites (WPC) were manufactured using 40% mahogany wood flour (WF). The effect of particle size (0.074 to 0.149 mm, 0.177 to 0.250 mm, and 0.400 to 0.841 mm) on the selected properties of PP and rPP composites was studied. The influence of 3% maleic anhydride grafted polypropylene (MAPP) presence in the formulation was also evaluated. Test specimens were manufactured using a combination of extrusion and injection molding processes. The density and mechanical properties, such as flexural strength, flexural modulus, tensile strength, tensile modulus, elongation at break, hardness and impact strength values were determined. Morphology of the manufactured composites was also studied using scanning electron microscopy (SEM) analysis. Results showed that the particle size, polypropylene type (neat or recycled), and presence of MAPP had important effects on WPC’s properties. Density, flexural modulus, tensile modulus, and impact strength values increased with decreased particle size regardless of the presence of MAPP. Flexural strength values increased with decreased particle size without MAPP. Regardless of particle size, addition of MAPP in composites provided higher flexural strength, flexural modulus, tensile strength, and tensile modulus values but lower elongation at break values compared to composites without MAPP.

scholarly journals THERMAL, DYNAMIC MECHANICAL ANALYSIS AND MECHANICAL PROPERTIES OF POLYBUTYLENE TEREPHTHALATE/POLYETHYLENE TEREPHTHALATE BLENDS

2020 ◽  
Vol 82 (5) ◽  
Author(s):  
Muhammad Akmal Ahmad Saidi ◽  
Azman Hassan ◽  
Mat Uzir Wahit ◽  
Lai Jau Choy ◽  
Hazleen Anuar
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Dynamic Mechanical Analysis ◽  
Polyethylene Terephthalate ◽  
Mechanical Analysis ◽  
Polybutylene Terephthalate ◽  
Elongation At Break ◽  
Dynamic Mechanical

Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and mechanical tests were conducted to characterize the properties of polybutylene terephthalate/polyethylene terephthalate (PBT/PET) blends. PBT and PET were blended at different PBT/PET ratios (80/20, 60/40, 40/60, 20/80) via twin screw extruder prior to injection molding. DSC characterization showed a single glass transition temperature for all PBT/PET blends indicating that the miscibility occurred in the amorphous region. From DMA results, loss modulus and tan δ also showed a single peak for all PBT/PET blends, confirming the DSC results. At room temperature, PBT/PET 20/80 has the highest storage modulus followed by PBT/PET 80/20 blend. PET has higher tensile strength, flexural strength, Young’s and flexural modulus than PBT but lower in elongation at break and impact strength. PBT/PET 80/20 blend has the highest tensile strength, flexural strength, elongation at break, and impact strength compared to other PBT/PET blends. PBT/PET 80/20 blend can be suggested as an optimum formulation with balanced mechanical properties in terms of stiffness and toughness.

Preparation and Properties of Polypropylene/Pottery Stone Composites

2011 ◽  
Vol 347-353 ◽  
pp. 1778-1781
Author(s):  
Zheng Hua Song ◽  
T Ruphun ◽  
T Karnjanamayul
Keyword(s):  
Thermal Stability ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Average Particle Size ◽  
Flow Index ◽  
Average Particle ◽  
Elongation At Break

Pottery stone (PTS) filled polypropylene (PP) composites were prepared using a twin screw extruder and injection molding machine. PTS used in this study is in a particulate form with an average particle size of 6.95 μm. The melt flow index (MFI), tensile properties (tensile strength, Young’s modulus and elongation at break), notched-impact strength, flexural strength, thermal stability and morphology of the PP/PTS composites were investigated. The results showed that the incorporation of PTS into the PP matrix caused a slight decrease in the MFI, an increase in the tensile strength (5 and 10 phr, but 10 phr optimal), Young’s modulus (all, but 20 phr optimal), impact strength (all, but 20 phr optimal), flexural strength (all, but 10 phr optimal) and thermal stability (all, but 20 phr optimal) and a decrease in the elongation at break. Therefore, PTS can be effectively used as reinforcing filler in PP. The fractured surfaces of the composites displayed the well dispersed of PTS in PP matrix and also exhibited plastic deformation feature.

Study on Direct Reactive Compatibilization of HDPE/Wood-Flour Composites

2011 ◽  
Vol 239-242 ◽  
pp. 2346-2351 ◽  
Author(s):  
Yue Wen Li ◽  
Xin Hua Chen
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Wood Flour ◽  
Reactive Extrusion ◽  
Extrusion Temperature ◽  
Elongation At Break ◽  
Reactive Compatibilization ◽  
Optimum Dosage ◽  
Anchoring Strength

Reactive compatibilization between high-density polyethylene(HDPE) and wood-flour was achieved via direct reactive extrusion of maleic anhydride(MAH), initiator, HDPE and wood-flour. Impact rupture surface of the composites was observed by scanning electron microscope(SEM), and its load deformation temperature(HDT) and mechanical properties were tested. Effect of MAH dosage, initiator activity and extrusion temperature on the reactive compatibilization was analysed. The result indicated that the anchoring strength of interface in the composites was obviously strengthened and its HDT, tensile strength, flexural strength, notched impact strength and elongation at break were distinctly improved due to the addition of MAH and dicumyl peroxide(DCP). When the composites were extruded at 180°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 79°C, 34Mpa, 36Mpa, 30% and 10KJ.m-2, which respectively increased by 10°C, 62%, 33%, 200% and 150% than that of the composites without reactive compatibilization, and when the composites were extruded at 200°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 78°C, 34Mpa, 36Mpa, 24% and 8KJ.m-2, which respectively increased by 12°C, 55%, 33%, 200% and 100% than that of the composites without reactive compatibilization. In the case of DCP and MAH as compatibilizer, there was an optimum dosage of MAH. The optimum dosage was shifted forward as extrusion temperature increased.

Preparation and Characterization of β-glucosidase Films for Stabilization and Handling in Dry Configurations

2020 ◽  
Vol 21 (8) ◽  
pp. 741-747
Author(s):  
Liguang Zhang ◽  
Yanan Shen ◽  
Wenjing Lu ◽  
Lengqiu Guo ◽  
Min Xiang ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Protein Function ◽  
Protein Stabilization ◽  
Functional Protein ◽  
Elongation At Break ◽  
Gelatin Films ◽  
The Stability ◽  
And Function ◽  
General Method

Background: Although the stability of proteins is of significance to maintain protein function for therapeutical applications, this remains a challenge. Herein, a general method of preserving protein stability and function was developed using gelatin films. Method: Enzymes immobilized onto films composed of gelatin and Ethylene Glycol (EG) were developed to study their ability to stabilize proteins. As a model functional protein, β-glucosidase was selected. The tensile properties, microstructure, and crystallization behavior of the gelatin films were assessed. Result: Our results indicated that film configurations can preserve the activity of β-glucosidase under rigorous conditions (75% relative humidity and 37°C for 47 days). In both control films and films containing 1.8 % β-glucosidase, tensile strength increased with increased EG content, whilst the elongation at break increased initially, then decreased over time. The presence of β-glucosidase had a negligible influence on tensile strength and elongation at break. Scanning electron-microscopy (SEM) revealed that with increasing EG content or decreasing enzyme concentrations, a denser microstructure was observed. Conclusion: In conclusion, the dry film is a promising candidate to maintain protein stabilization and handling. The configuration is convenient and cheap, and thus applicable to protein storage and transportation processes in the future.

Mechanical Property Improvement of Poly(Butylene Succinate) by Reinforcing with Modified Fumed Silica

2014 ◽  
Vol 1025-1026 ◽  
pp. 215-220 ◽  
Author(s):  
Sasirada Weerasunthorn ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fumed Silica ◽  
Tensile Modulus ◽  
Silica Particles ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Ir Spectrophotometry

Fumed silica particles (SiO2) were directly added into poly (butylene succinate) (PBS) by melt mixing process. The effects of amount of fumed silica particles on mechanical properties of PBS/fumed silica composites, those are tensile strength, tensile modulus, impact strength as well as flexural strength, were investigated. It was found that the mechanical properties decreased with increasing fumed silica loading (0-3 wt%). In order to increase polymer-filler interaction, fumed silica was treated with 3-glycidyloxypropyl trimethoxysilane (GPMS), and its structure was analyzed by FT-IR spectrophotometry. The PBS/modified was found to possess better tensile strength, tensile modulus, impact strength and flexural strength that those of PBS/fumed silica composites.

Sign in / Sign up

Export Citation Format

Share Document