Effect of aluminum nitride concentration on different physical properties of low density polyethylene based nanocomposites

2017 ◽  
Vol 37 (8) ◽  
pp. 765-775 ◽  
Author(s):  
Omer Bin Sohail ◽  
Osamah A. Bin-Dahman ◽  
Mostafizur Rahaman ◽  
Mamdouh A. Al-Harthi
Keyword(s):  
Electrical Conductivity ◽  
Dielectric Constant ◽  
Aluminum Nitride ◽  
Tensile Modulus ◽  
Theoretical Models ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Scanning Calorimetry ◽  
Composite Systems ◽  
Present Composite

Abstract In this study, blends of low-density polyethylene (LDPE)/aluminum nitride (AlN) ceramic nanocomposites have been prepared through melt blending technique. Increased loading of AIN leads to reduction in tensile properties but improvement in rheological property (storage modulus). The rheological behavior tends to become unique at higher frequencies (≥10 rad/s). Differential scanning calorimetry (DSC) results show that the total crystallinity has decreased with the increase in AlN loading in the composites. It is seen that there is an improvement in electrical conductivity, dielectric constant, and flammability properties with the addition of AlN in the nanocomposites. The experimental data of tensile modulus, electrical conductivity, and dielectric constant have been fitted with some available theoretical models to check the models’ applicability for the present composite systems. Results show that only Nicolais-Nicodemo model, McCullough model, and Rahaman-Khastgir model are applicable for predicting the tensile modulus, electrical conductivity, and dielectric constant of the composites, respectively.

scholarly journals Performance of Straw/Linear Low Density Polyethylene Composite Prepared with Film-Roll Hot Pressing

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 860
Author(s):  
Lei Zhang ◽  
Huicheng Xu ◽  
Weihong Wang
Keyword(s):  
Hot Pressing ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Thermoplastic Composites ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Scanning Calorimetry ◽  
Polyethylene Composite ◽  
Extrusion Method

Thermoplastic composites are usually prepared with the extrusion method, and straw reinforcement material must be processed to fiber or powder. In this study, film-roll hot pressing was developed to reinforce linear low density polyethylene (LLDPE) with long continuous straw stems. The long straw stems were wrapped with LLDPE film and then hot pressed and cooled to prepare straw/LLDPE composite. Extruded straw fiber/LLDPE composite was prepared as a control. The mechanical properties of these LLDPE-based composites were evaluated. The hot pressed straw/LLDPE composite provided higher tensile strength, tensile modulus, flexural strength, flexural modulus, and impact strength than the traditional extruded straw/LLDPE composite, by 335%, 107%, 68%, 57%, and 181%, respectively, reaching 35.1 MPa, 2.65 GPa, 3.8 MPa, 2.15 GPa, and 25.1 KJ/m2. The density of the hot pressed straw/LLDPE composite (0.83 g/cm3) was lower than that of the extruded straw/LLDPE composite (1.31 g/cm3), and the former had a higher ratio of strength-to-weight. Scanning electron microscopy indicated that the orientation of the straws in the composite was better with the new method. Differential scanning calorimetry tests revealed that in hot pressed straw/LLDPE composite, straw fibers have a greater resistance to the melting of LLDPE than extruded composite. Rotary rheometer tests showed that the storage modulus of the hot pressed straw/LLDPE was less affected by frequency than that of the extruded composite, and the better elastic characteristics were pronounced at 150 °C. The hot pressed straw/LLDPE composite absorbed more water than the extruded composite and showed a potential ability to regulate the surrounding relative humidity. Our results showed that straw from renewable sources can be used to produce composites with good performance.

Investigation of the morphology and properties of the polypropylene/low-density polyethylene/wood powder and the maleic anhydride grafted polypropylene/low-density polyethylene/wood powder polymer blend composites

2016 ◽  
Vol 51 (14) ◽  
pp. 2045-2059 ◽  
Author(s):  
DG Dikobe ◽  
AS Luyt
Keyword(s):  
Maleic Anhydride ◽  
Tensile Modulus ◽  
Ternary Systems ◽  
Low Density Polyethylene ◽  
Infrared Analysis ◽  
Low Density ◽  
Wood Powder ◽  
Scanning Calorimetry ◽  
Polyethylene Blends ◽  
Polyethylene Blend

The properties of polypropylene/low-density polyethylene and maleic anhydride grafted polypropylene/low-density polyethylene blends, and their wood powder composites are compared in this study. The blends contained equal amounts of polymers, and the wood powder was added into the blends to form polypropylene/low-density polyethylene/wood powder and maleic anhydride grafted polypropylene/low-density polyethylene/wood powder ternary systems. The Fourier-transform infrared analysis of the blends and composites did not provide any evidence of significant interactions between the different components, although the rest of the results clearly showed that maleic anhydride grafted polypropylene and wood powder significantly interacted, and that there was some interaction between maleic anhydride grafted polypropylene and low-density polyethylene. The differential scanning calorimetry and dynamic mechanical analysis results confirmed the immiscibility of polypropylene and low-density polyethylene, and polypropylene and maleic anhydride grafted polypropylene, and indicated that wood powder was distributed in both the low-density polyethylene and polypropylene phases in the polypropylene/low-density polyethylene blend, but most probably only in the maleic anhydride grafted polypropylene phase in the maleic anhydride grafted polypropylene/low-density polyethylene blend. The polypropylene/low-density polyethylene and maleic anhydride grafted polypropylene/low-density polyethylene blends were found to be more thermally stable than the neat polymers, while the presence of wood powder in both polymer blends further increased the thermal stability of the polymers. The blends and composites with maleic anhydride grafted polypropylene showed higher tensile modulus values and lower elongation at break values than the composites with polypropylene, while the stress at break values of the two sets of samples were comparable.

Crystallinity and Influence of Citric Acid as a Compatibilizer in Low Density Polyethylene/Jackfruit Seed Flour Blends

2015 ◽  
Vol 815 ◽  
pp. 14-18
Author(s):  
P. Santhiya ◽  
S.T. Sam ◽  
H. Kamarudin ◽  
S. Ragunathan ◽  
N.Z. Noriman ◽  
...  
Keyword(s):  
Differential Scanning Calorimetry ◽  
Citric Acid ◽  
Heating Temperature ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Scanning Calorimetry ◽  
Seed Flour ◽  
Flour Blends ◽  
Internal Mixer

The properties of blends made from low density polyethylene (LDPE) with various concentration of jackfruit seeds flour (JSF) with the presence of citric acid (CA) were investigated. The JSF content was varied from 0 to 20 wt%. The JSF were blended with LDPE by using an internal mixer (Brabender) at a temperature of 150°C. The test was carried out by using differential scanning calorimetry (DSC), with heating temperature of 100C/min. The crystallinity had improved with the presence of CA. However, the crystallinity slightly reduced with the increasing JSF content and further increased with the presence of CA.

Thermal Conductivity of Low Density Polyethylene Foams Part I: Comprehensive Study of Theoretical Models

2019 ◽  
Vol 28 (4) ◽  
pp. 745-754 ◽  
Author(s):  
Hasanzadeh Rezgar ◽  
Azdast Taher ◽  
Doniavi Ali ◽  
Eungkee Lee Richard
Keyword(s):  
Thermal Conductivity ◽  
Theoretical Models ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Comprehensive Study

Impact of hybrid nanosilica and nanoclay on the properties of palm rachis-reinforced recycled linear low-density polyethylene composites

2020 ◽  
pp. 089270572094421
Author(s):  
Wagih Abdel Alim Sadik ◽  
Abdel Ghaffar Maghraby El Demerdash ◽  
Rafik Abbas ◽  
Alaa Bedir
Keyword(s):  
Tensile Modulus ◽  
Stress Transfer ◽  
Microscopy Study ◽  
Hybrid Nanoparticles ◽  
Morphological Properties ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Plastic Composite ◽  
Blending Method

The main goal of this work was to assess the technical feasibility of palm rachis (PR) as a reinforcing agent in the production of wood–plastic composites. Recycled linear low-density polyethylene/PR fiber composites were prepared at constant content (3 phc (per hundred compounds)) of maleic anhydride-grafted polyethylene as compatibilizer by melt blending method utilizing a two-roll mill and compression molding. The effect of nanosilica (NS), nanoclay (NC), and hybrid nanoparticles (NSNC) at different concentrations (2, 4, and 6 phc) on mechanical, physical, thermal, and morphological properties was investigated. The results of mechanical properties measurements demonstrated that when 6 phc NS, 4 phc NC, and 4 phc NSNC were added, tensile, modulus strength, and hardness reached their optimum values. At a high level of NC loading (6 phc), the increased populace of NC layers led to agglomeration and stress transfer gets restricted. Elongation at break and Izod impact strength were decreased by the incorporation of different nanoparticles. Water absorption and thickness swelling of prepared composites were found to decrease on the incorporation of NS and NC. In addition, the thermal stability showed slightly improved by the addition of nanoparticles, but there are no perceptible changes in the values of melting temperature by increasing the content of NS and NC or NSNC. Scanning electron microscopy study approved the good interaction of the PR fibers with the polymer matrix as well as the effectiveness of NS and NC in the improvement of the interaction. The finding indicated that wood–plastic composite treated by NS had the highest properties than other composites.

Degradation of epoxidized natural rubber compatibilized linear low density polyethylene/ soya powder blends: the effect of natural weathering

2013 ◽  
Vol 33 (7) ◽  
pp. 579-588 ◽  
Author(s):  
S.T. Sam ◽  
H. Ismail ◽  
H.P.S. Abdul Khalil
Keyword(s):  
Natural Rubber ◽  
Exposure Period ◽  
Natural Weathering ◽  
Epoxidized Natural Rubber ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Scanning Calorimetry ◽  
Powder Blends ◽  
Compatibilized Blends

Abstract In the present study, linear low density polyethylene (LLDPE)/soya powder blends were compatibilized with epoxidized natural rubber (ENR 50) and exposed to natural weathering. The exposure period for the blends was 1 year. It was found that the degradability of the compatibilized blends was higher than that of uncompatibilized blends. Fourier transform infrared (FTIR) spectra, the tensile test, scanning electron microscopy (SEM), and differential scanning calorimetry (DSC) were applied to analyze the degradability of the blends. IR spectra showed that the carbonyl index (CI) of the blends increased as a function of exposure period and soya powder content. The compatibilized blends gave higher carbonyl indices. The retention tensile strength and elongation at break (Eb) of the compatibilized blends after weathering was generally lower than for the uncompatibilized blends. The increase of crystallinity also indicated a reduction of the amorphous portion after degradation. The higher crystallinity in compatibilized blends further confirms the higher degradability of ENR 50 compatibilized blends. The weight loss and molecular weight change indicated that the incorporation of ENR 50 into LLDPE/soya powder blends can enhance the degradability of the blends upon outdoor exposure.

Biodegradation study of bio-corn flour filled low density polyethylene composites assessed by natural soil

2016 ◽  
Vol 36 (3) ◽  
pp. 245-252 ◽  
Author(s):  
Samira Sahi ◽  
Hocine Djidjelli ◽  
Amar Boukerrou
Keyword(s):  
Filler Content ◽  
Alkali Treatment ◽  
Reactive Extrusion ◽  
Low Density Polyethylene ◽  
Natural Soil ◽  
Low Density ◽  
Corn Flour ◽  
Scanning Calorimetry ◽  
Soil Burial ◽  
Morphological Studies

Abstract This paper illustrates the aim to introduce biodegradable vegetable filler in synthetic polymers to prepare novel biodegradable composites. Low density polyethylene/alkali treated corn flour (LDPE/ATCF) composites were prepared by reactive extrusion using a twin-screw extruder. The microstructure, thermal properties and tensile properties were evaluated and compared with virgin LDPE. The Fourier transform infrared (FTIR) spectra showed a decrease in the hydrophilic nature of corn flour (CF) after alkali treatment. Scanning electron microscopy (SEM) micrographs showed good dispersion between matrix and filler. The tensile and elongation at break decreased by increasing the filler content in the composites. However, the Young’s modulus increased with the increase in filler content. The biodegradation of composites was studied in the environment using the soil burial test for 6 months. Differential scanning calorimetry (DSC) analysis showed an increase of the melting enthalpy (ΔHm) and crystallinity of LDPE with evidence of degradation. The biodegradability of the composites was enhanced with increasing ATCF content in the matrix. This result was supported by weight loss and degraded surface of composites observed through morphological studies. From the results, we conclude that the use of ATCF as filler in LDPE reduces pollution problems. This is advantageous for both the economy and the environment.

Exploration on compatibilizing effect of nonionic, anionic, and cationic surfactants on mechanical, morphological, and chemical properties of high-density polyethylene/low-density polyethylene/cellulose biocomposites

2015 ◽  
Vol 30 (6) ◽  
pp. 855-884 ◽  
Author(s):  
AK Sudari ◽  
AA Shamsuri ◽  
ES Zainudin ◽  
PM Tahir
Keyword(s):  
Mechanical Properties ◽  
High Density Polyethylene ◽  
Sodium Stearate ◽  
High Density ◽  
Low Density Polyethylene ◽  
Hexadecyltrimethylammonium Bromide ◽  
Low Density ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
Compatibilizing Effect

Three types of surfactants, specifically cationic, anionic, and nonionic, at different weight percentages were added into high-density polyethylene/low-density polyethylene/cellulose (HDPE/LDPE/cellulose) biocomposites via melt mixing. The cationic and anionic surfactants which are hexadecyltrimethylammonium bromide (HTAB) and sodium stearate (SS), respectively, were added from 4 to 20 wt%, whereas the nonionic surfactant which is sorbitan monostearate (SM) was added from 1 to 5 wt%. The mechanical testing results exhibited that the addition of HTAB increased tensile strength and tensile modulus, while SS deteriorated mechanical properties, while SM increased impact strength and tensile extension of the biocomposites. Based on the mechanical properties results, optimum weight percentages of HTAB and SM were 12 wt% and 4 wt%, respectively. The scanning electron microscopic micrographs displayed that the amount of cellulose fillers pullout decreased with the addition of HTAB, followed by SM, but it increased with SS. Fourier transform infrared spectra, X-ray diffractometer patterns, thermogravimetric analysis results, and differential scanning calorimetry thermograms have confirmed the presence of physical interactions only with the addition of HTAB and SM. Based on the results, compatibilizing effect was found in HTAB, whereas SM has not showed compatibilizing effect but instead plasticizing effect. However, neither compatibilizing nor plasticizing effect was exhibited by SS.

Thermal Properties of Linear-Low Density Polyethylene (LLDPE)/Soya Spent Powder Blends with the Addition of Epoxidised Natural Rubber

2013 ◽  
Vol 795 ◽  
pp. 433-437 ◽  
Author(s):  
S.T. Sam ◽  
N.Z. Noriman ◽  
S. Ragunathan ◽  
O.H. Lin ◽  
H. Ismail
Keyword(s):  
Thermal Properties ◽  
Natural Rubber ◽  
Mixing Time ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Scanning Calorimetry ◽  
Powder Composites ◽  
Powder Content ◽  
Internal Mixer

Soya spent powder as an inexpensive and renewable source has been used as a filler for linear-low density polyethylene (LLDPE) in this study. Linear-low density polyethylene (LLDPE)/soya spent powder composites were prepared by using Haake internal mixer. The mixing time was 10 minutes at 150°C with rotor speed 50 rpm. Epoxidised natural rubber (ENR 50) has been used as a compatibilizer in the present study. The thermal properties of the LLDPE/soya spent powder composites with and without ENR were studied with a differential scanning calorimetry (DSC). The crystallinity of the LLDPE/soya spent powder composites decreased with increasing soya spent powder content. However, the addition of ENR 50 as a compatibilizer increased the crystallinity of the LLDPE/soya spent powder composites.

Sign in / Sign up

Export Citation Format

Share Document