The Structure of the Interfacial Layer and Ozone Protective Action of Ethylene-Propylene-Diene Elastomers in Covulcanizates with Butadiene-Nitrile Rubbers

2015 ◽  
pp. 237-256 ◽  
Keyword(s):  
Interfacial Layer ◽  
Protective Action ◽  
Ethylene Propylene ◽  
Nitrile Rubbers

Modification of ethylene-propylene-diene elastomers to improve the ozone resistance of their covulcanizates with butadiene-nitrile rubbers

2011 ◽  
Vol 53 (2) ◽  
pp. 133-142 ◽  
Author(s):  
N. M. Livanova ◽  
V. A. Shershnev ◽  
M. V. Dudnik ◽  
Yu. O. Andreasyan ◽  
A. A. Popov
Keyword(s):  
Ethylene Propylene ◽  
Nitrile Rubbers ◽  
Ozone Resistance

Cure Adhesion in the Interface of Fluorinated and Nitrile Rubbers

1987 ◽  
Vol 60 (5) ◽  
pp. 822-836 ◽  
Author(s):  
Kunio Mori
Keyword(s):  
Composite Materials ◽  
Interfacial Layer ◽  
Intermolecular Forces ◽  
Interfacial Region ◽  
Nitrile Rubbers

Abstract Recently there has been a great deal of interest in new composite rubbery materials. Good properties require the reinforcement of the interfacial region which is formed between different rubbers. In order to strengthen the interfacial region, it is necessary to increase the thickness of the interfacial layer and the intermolecular forces. However, in a laminate and blends of rubbers with physically and chemically different properties, it is often very difficult to obtain this as, for example, in the case of fluorinated (FR) and nitrile (NBR) rubbers. This work indicates newly developed vulcanization systems which are very effective in producing FR-NBR composite materials with very good properties, because they induce interpolymer interactions.

Solvent-assisted osmium staining of butyl acrylate and ethylene-propylene-diene in a styrene acrylonitrile matrix

1993 ◽  
Vol 51 ◽  
pp. 900-901 ◽  
Author(s):  
Gudrun A. Hutchins
Keyword(s):  
Butyl Acrylate ◽  
Room Temperature ◽  
Osmium Tetroxide ◽  
Staining Procedure ◽  
Reactive Site ◽  
Ethylene Propylene ◽  
Minimal Distortion ◽  
Styrene Acrylonitrile ◽  
Engineering Polymers ◽  
Effective Reaction

In order to optimize the toughening effect of elastomers in engineering polymers, it is necessary to characterize the size, morphology and dispersion of the specific elastomer within the polymer matrix. For unsaturated elastomers such as butadiene or isoprene, staining with osmium tetroxide is a well established procedure. The residual carbon-carbon double bond in these materials is the reactive site and forms a 1,2-dilato complex with the OsO4. Incorporation of osmium tetroxide into the elastomer not only produces sufficient contrast for TEM, but also crosslinks the elastomer sufficiently so that ultramicrotomy can be accomplished at room temperature with minimal distortion.Blends containing saturated elastomers such as butyl acrylate (BA) and ethylene propylene diene monomer (EPDM) cannot be stained directly with OsO4 because effective reaction sites such as C=C or -NH2 are not available in sufficient number. If additional reaction sites can be introduced selectively into the elastomer by a chemical reaction or the absorption of a solvent, a modified, two-step osmium staining procedure is possible.

Liquorice exaggerates protective action of Solanum xanthocarpum against cigarette smoke induced pulmonary inflammation

Planta Medica ◽  
2014 ◽  
Vol 80 (10) ◽  
Author(s):  
RA Manek ◽  
NR Sheth ◽  
JR Chavda ◽  
JD Vaghasiya ◽  
KP Modi ◽  
...  
Keyword(s):  
Cigarette Smoke ◽  
Protective Action ◽  
Pulmonary Inflammation ◽  
Solanum Xanthocarpum

Action of Lysolecithin on Blood Platelets

1963 ◽  
Vol 09 (03) ◽  
pp. 512-524 ◽  
Author(s):  
Chava Kirschmann ◽  
Sara Aloof ◽  
Andre de Vries
Keyword(s):  
Blood Platelets ◽  
Protective Action ◽  
Platelet Surface ◽  
Washed Platelet ◽  
Sufficient Concentration ◽  
Saline Medium

SummaryLysolecithin is adsorbed to washed blood platelets and, at sufficient concentration, lyses them, inhibits their clot-retracting activity and promotes their thromboplastin-generating activity. Lysolecithin adsorption to the platelet was studied by using P32-labelled lysolecithin obtained from the liver of rats injected with labelled orthophosphate. The amount of lysolecithin adsorbed to the surface of the washed platelet in saline medium is dependent on the concentration of lysolecithin in solution and reaches saturation — 5 × 10-8 jig per platelet — at a concentration of 9—10 µg per ml. Platelet lysis in saline medium begins at a lysolecithin concentration higher than 18 jig per ml. Plasma and albumin prevent adsorption of lysolecithin to the platelet and protect the platelet from damage by lysolecithin. Albumin is able to remove previously adsorbed lysolecithin from the platelet surface. The protective action of plasma explains the lack of platelet damage in blood, the plasma lecithin of which has been converted to lysolecithin by the action of Vipera palestinae venom phosphatidase, in vitro and in vivo.

Scalability of MOCVD-deposited Hafnium Oxide

2003 ◽  
Vol 765 ◽  
Author(s):  
S. Van Elshocht ◽  
R. Carter ◽  
M. Caymax ◽  
M. Claes ◽  
T. Conard ◽  
...  
Keyword(s):  
Hafnium Oxide ◽  
Interfacial Layer ◽  
Gate Dielectric ◽  
Deposition Process ◽  
Oxide Thickness ◽  
Process Conditions ◽  
Primary Concern ◽  
Gate Electrode ◽  
K Value ◽  
High K

AbstractBecause of aggressive downscaling to increase transistor performance, the physical thickness of the SiO2 gate dielectric is rapidly approaching the limit where it will only consist of a few atomic layers. As a consequence, this will result in very high leakage currents due to direct tunneling. To allow further scaling, materials with a k-value higher than SiO2 (“high-k materials”) are explored, such that the thickness of the dielectric can be increased without degrading performance.Based on our experimental results, we discuss the potential of MOCVD-deposited HfO2 to scale to (sub)-1-nm EOTs (Equivalent Oxide Thickness). A primary concern is the interfacial layer that is formed between the Si and the HfO2, during the MOCVD deposition process, for both H-passivated and SiO2-like starting surfaces. This interfacial layer will, because of its lower k-value, significantly contribute to the EOT and reduce the benefit of the high-k material. In addition, we have experienced serious issues integrating HfO2 with a polySi gate electrode at the top interface depending on the process conditions of polySi deposition and activation anneal used. Furthermore, we have determined, based on a thickness series, the k-value for HfO2 deposited at various temperatures and found that the k-value of the HfO2 depends upon the gate electrode deposited on top (polySi or TiN).Based on our observations, the combination of MOCVD HfO2 with a polySi gate electrode will not be able to scale below the 1-nm EOT marker. The use of a metal gate however, does show promise to scale down to very low EOT values.

Effects of Aging on the Morphology of Rubber-Brass Interfacial Layer

2011 ◽  
Vol 39 (1) ◽  
pp. 20-43 ◽  
Author(s):  
A. Ashirgade ◽  
P. B. Harakuni ◽  
W. J. Vanooij
Keyword(s):  
Chemical Composition ◽  
Interfacial Layer ◽  
Secondary Ion Mass Spectrometry ◽  
Morphological Changes ◽  
Grazing Incidence ◽  
Complex Nature ◽  
Rubber Compound ◽  
Tire Cord ◽  
Morphological Transformation ◽  
Adhesion Promoter

Abstract Adhesion between rubber compound and brass-plated steel tire cord is crucial in governing the overall performance of tires. The rubber-brass interfacial adhesion is influenced by the chemical composition and thickness of the interfacial layer. It has been shown that the interfacial layer consists mainly of sulfides and oxides of copper and zinc. This paper discusses the effect of changes in the chemical composition and the structure of the interfacial layers due to addition of adhesion promoter resins. Grazing incidence x-ray diffraction (GIXRD) experiments were run on sulfidized polished brass coupons previously bonded to five experimental rubber compounds. It was confirmed that heat and humidity conditions lead to physical and chemical changes of the rubber-steel tire cord interfacial layer, closely related to the degree of rubber-brass adhesion. Morphological transformation of the interfacial layer led to loss of adhesion after aging. The adhesion promoter resins inhibit unfavorable morphological changes in the interfacial layer, thus stabilizing it during aging and prolonging failure. Tire cord adhesion tests illustrated that the one-component resins improved adhesion after aging using a rubber compound with lower cobalt loading. Based on the acquired diffraction profiles, these resins were also found to impede crystallization of the sulfide layer after aging, leading to improved adhesion. Secondary ion mass spectrometry depth profiles and scanning electron microscopy micrographs strongly corroborated the findings from GIXRD. This interfacial analysis adds valuable information to our understanding of the complex nature of the rubber-brass bonding mechanism.

Sign in / Sign up

Export Citation Format

Share Document