An Evaluation of Two-Level Seismic Design Procedure

1993 ◽  
Vol 9 (1) ◽  
pp. 121-135 ◽  
Author(s):  
Chia-Ming Uang
Keyword(s):  
Structural Damage ◽  
Limit State ◽  
Design Procedure ◽  
Reduction Factor ◽  
Performance Criteria ◽  
Ultimate Limit State ◽  
Seismic Codes ◽  
Seismic Force ◽  
Force Reduction Factor ◽  
Force Reduction

The two-level design philosophy is recognized by modern seismic codes. When this philosophy is implemented in the code, the intensities of the two design earthquakes, the structural performance criteria, explicit versus implicit design approach, and the effectiveness to achieve the performance criteria vary considerably from one code to the other. For the ultimate limit state, the UBC was compared with seismic codes of Canada, Japan, and Eurocode. It was found that a trend to deviate from the UBC approach of using a single seismic force reduction factor (i.e., Rw) is apparent. Instead, an approach using a compound force reduction factor which considers the contribution of structural ductility and structural overstrength is preferred. For the serviceability limit state, a comparison of the level of design earthquakes and performance criteria of the UBC, Tri-Services Manual, and the Japanese code indicates that the UBC produces the most flexible structure, and that UBC does not control structural damage. It is suggested that the UBC adopts an explicit serviceability design procedure.

Development of Seismic Force Reduction and Displacement Amplification Factors for Autoclaved Aerated Concrete Structures

2006 ◽  
Vol 22 (1) ◽  
pp. 267-286 ◽  
Author(s):  
Jorge L. Varela ◽  
Jennifer E. Tanner ◽  
Richard E. Klingner
Keyword(s):  
Reduction Factor ◽  
Test Results ◽  
Lateral Loads ◽  
Autoclaved Aerated Concrete ◽  
Laboratory Test Results ◽  
Seismic Force ◽  
Force Reduction Factor ◽  
Aerated Concrete ◽  
Hysteretic Characteristics ◽  
Force Reduction

This paper addresses the development and application of a rational procedure to select the seismic force reduction factor ( R) and the displacement amplification factor ( Cd) for the design of autoclaved aerated concrete (AAC) structures. The values of R and Cd are proposed based on a combination of laboratory test results and numerical simulation. The test results are obtained from 14 AAC shear-wall specimens tested under simulated gravity and quasi-static reversed cyclic lateral loads. Analytical responses are predicted using nonlinear analysis models whose hysteretic characteristics are based on the experimentally observed responses. Using an iterative procedure, typical AAC structures are designed using successively larger trial values of the factor, R, until the structure's response (either ductility or drift) exceeds the experimentally determined capacity. A lower fractile of those critical values, modified for probable structural overstrength, is taken as a reasonable value of 3 for R. Using an analogous procedure, a reasonable value of Cd is determined as 3. These values will undoubtedly be refined based on field experience, just as they have been for other structural systems.

Underground Tunnels Exposed to Internal Blast: Effect of the Explosive Source Position

2016 ◽  
Vol 711 ◽  
pp. 852-859
Author(s):  
Matteo Colombo ◽  
Paolo Martinelli ◽  
Marco di Prisco
Keyword(s):  
Limit State ◽  
Design Procedure ◽  
Internal Diameter ◽  
Ultimate Limit State ◽  
Fe Model ◽  
Average Width ◽  
Internal Explosion ◽  
Explosive Source ◽  
Blast Effect ◽  
Tunnel Cross Section

The design procedure recently proposed by the same authors and based on a simplified FE model for underground tunnels subjected to internal explosion is extended in this work taking into account different possible positions of the explosive source inside the tunnel. The situation in which the internal explosion is preceded by fire accidents is also analyzed. The reference situation is represented by the explosive source located at the center of the tunnel cross–section. The tunnel geometry considered is that of the metro line in Brescia, Italy. It has an internal diameter of about 8.15 m and is located about 23.1 m below the surface. Six segments and a smaller key segment (6+1) make up the tunnel. The ring has an average width of about 1.5 m. Dynamic analyses were carried out in order to reproduce the blast scenario. The aim of this work is to evaluate the influence of the position of the explosive source on the tunnel dynamic response. An ultimate limit state criterion based on the eccentric ultimate flexural capacity and capable of including fire–blast interaction is adopted. An innovative layered precast tunnel segment solution made of different fiber–reinforced cementitious composites is considered.

scholarly journals A RATIONALIZED SEISMIC DESIGN METHOD FOR BUILDINGS IN EARTHQUAKE-PRONE DEVELOPING COUNTRIES

2021 ◽  
Vol 11 (4) ◽  
pp. 266-279
Author(s):  
Tint Lwin ◽  
Takeshi Koike ◽  
Ji Dang
Keyword(s):  
Developing Countries ◽  
Seismic Design ◽  
Design Method ◽  
Limit State ◽  
Design Procedure ◽  
Ultimate Limit State ◽  
Design Guideline ◽  
Seismic Safety ◽  
Seismic Design Method ◽  
Ultimate Limit

In general, the US codes such as the UBC-97 and ASCE-7 are widely used in developing countries including Myanmar, Syria, Philippines and so on. When the current seismic design guideline based on the UBC-97 and ACI 318-99 in Myanmar is assessed, several problems can be found in the following items: firstly, the fundamental period is not checked in modeling; secondly, reduction factor R is introduced a priori for the base shear estimation. And finally, a limit state assessment is done only for Design Basic Earthquake (DBE) but not for other design earthquakes. As a result, adequate yield strength is not checked for Maximum Operational Earthquake (MOE). Then there is no way to assess the seismic safety of the ultimate limit state for Maximum Considered Earthquake (MCE). In order to solve these problems, a rationalized seismic design method for earthquake prone developing countries is proposed. A new seismic design method is developed for MOE and MCE with adequate yield acceleration and typical period of the building estimated by using pushover analysis. A simplified procedure to estimate the inelastic response for a given design spectrum is also proposed. Finally, this design procedure can provide a rational method to assess the seismic safety for the ultimate limit of the building.

Period-dependent seismic force reduction factors for short-period structures

1991 ◽  
Vol 18 (4) ◽  
pp. 568-574 ◽  
Author(s):  
W. K. Tso ◽  
N. Naumoski
Keyword(s):  
Reduction Factor ◽  
Structural Systems ◽  
High Ductility ◽  
Base Shear ◽  
Ductility Demand ◽  
Seismic Design Code ◽  
Short Period ◽  
Seismic Force ◽  
Force Reduction ◽  
Reduction Factors

The seismic force reduction factors proposed in the seismic provisions of the National Building Code of Canada 1990 (NBCC 1990) are examined using ground motion records from two recent Canadian earthquakes. The displacement ductility demands are analyzed for structural systems with different ductility capacity. It is found that the NBCC 1990 force reduction factors, which are period independent, lead to a very high ductility demand for short-period structural systems. To avoid this, two types of period-dependent force reduction factors for short-period structures are investigated. The results show that the linearly varying period-dependent reduction factor represents a viable means to resolve the high ductility problems associated with short-period structural systems. Key words: earthquake, seismic, design, code, response, spectra, ductility, reduction factor, base shear.

Design of Mooring Lines of Floating Offshore Wind Turbine in Jeju Offshore Area

2014 ◽  
Author(s):  
Hyungjun Kim ◽  
Joonmo Choung ◽  
Gi-Young Jeon
Keyword(s):  
Wind Turbine ◽  
Limit State ◽  
Design Procedure ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Ultimate Limit State ◽  
Mooring Lines ◽  
Offshore Area ◽  
Floating Offshore Wind Turbine ◽  
Wind Turbine System

This paper presents a mooring design procedure of a floating offshore wind turbine. The offshore environment data of Jeju south sea collected from Korea Hydrographic and Oceanographic Administration (KHOA) are used as environmental conditions for hydrodynamic analysis. A semi-submersible floating wind turbine system is considered based on Offshore Code Comparison Collaborative Continuation (OC4) DeepCWind platform and the National Renewable Energy Laboratory (NREL) 5MW class wind turbine. Catenary mooring with studless chain is chosen as the mooring system. Important design decisions such as how large the nominal sizes are, how long the mooring lines are, how far the anchor points are located, are demonstrated in detail. Considering ultimate limit state and fatigue limit state based on 100-year return period and 50 year design life, respectively, long-term predictions of breaking strength and fatigue are performed.

scholarly journals On consistent nonlinear analysis of soil–structure interaction problems

2018 ◽  
Vol 40 (2) ◽  
pp. 86-95 ◽  
Author(s):  
Andrzej Truty
Keyword(s):  
Nonlinear Analysis ◽  
Soil Structure ◽  
Limit State ◽  
Design Procedure ◽  
Linear Structure ◽  
Soil Structure Interaction ◽  
Ultimate Limit State ◽  
Structure Interaction ◽  
Finite Element Software ◽  
Computational Strategy

AbstractNonlinear soil–linear structure computational strategy is commonly accepted in the community of geotechnical engineers using advanced finite element software for solving complex soil–structure interaction problems. However, further design procedure of the structural elements is carried out using increased values of the computed elastic stress resultants. It is absolutely not clear whether this method is conservative and, therefore, whether safe or not. To tackle this problem, a fully consistent nonlinear analysis of a deep excavation protected by the diaphragm wall is analysed here. The subsoil is modelled using the Hardening Soil model, while reinforced concrete is modelled using the modified Lee–Fenves model enhanced by the Eurocode 2 (EC2)-compatible creep module, developed by the author. It is shown that the commonly used nonlinear soil–linear structure computational strategy may yield insufficient amount of reinforcement from the ultimate limit state (ULS) and serviceability limit state (SLS) points of view. A consistent and conservative method of combining fully nonlinear analysis and the rules imposed by the EC2 is proposed.

scholarly journals Further comments on seismic design loads for bridges

1981 ◽  
Vol 14 (1) ◽  
pp. 3-11
Author(s):  
J. B. Berrill ◽  
M. J. N. Priestley ◽  
R. Peek
Keyword(s):  
New Zealand ◽  
Response Spectra ◽  
Reduction Factor ◽  
Base Shear ◽  
Attenuation Model ◽  
Design Spectra ◽  
Model Code ◽  
Force Reduction Factor ◽  
Background Material ◽  
Force Reduction

This paper provides background material to the loadings section
of the model code recently published by the Society's Discussion Group
on Bridge Design, and presents a preliminary re-evaluation of the design spectra given in the proposed code. The basis for the proposed zoning scheme, in which the present uniform Zone B is replaced by a transition zone, is discussed. Arguments are given underlying the return period coefficients, and the force reduction factor used in generating the inelastic response spectra of the code. It is likely that the design spectra and the values of the other coefficients determining base shear forces will need to be revised as further research results become available; however, the form of the base shear expression, and the loadings section
as a whole, should remain unchanged. Re-evaluated spectra suggest that
the seismic coefficient values given in the proposed code may be too large by about 25 percent in Zone A, and too low by as much as 40 percent in
 Zone C. While the reassessed values should be more reliable than the original ones, they are based on a Japanese attenuation model, which has
not yet been calibrated against New Zealand data. Further research is required to establish an appropriate attenuation model for New Zealand;
 to avoid undue proliferation of design loadings it is preferable to defer revision of the various coefficients in the proposed code until such a
model is available. Until this is done, the proposed spectra should be viewed with caution, particularly in Zone C.

A proposed strategy for seismic design of steel buildings

1999 ◽  
Vol 26 (5) ◽  
pp. 564-571
Author(s):  
DJL Kennedy ◽  
M S Medhekar
Keyword(s):  
Seismic Design ◽  
Limit State ◽  
Evaluation Criteria ◽  
Design Procedure ◽  
Ultimate Limit State ◽  
Seismic Zone ◽  
Steel Buildings ◽  
Limit States ◽  
Design Earthquake ◽  
Ultimate Limit

The conceptual basis of the seismic design procedure in the National Building Code of Canada is reviewed. The design earthquake is specified only for the ultimate limit states at which the performance of both ordinary and important buildings is evaluated by an elastic static analysis in all zones. Criteria for checking the serviceability limit states, which apply to moderate earthquakes that may occur relatively frequently in the life of the building, are not specified explicitly. It is suggested that the current design approach could be improved by adopting a design strategy that addresses as well the serviceability limit states and associated evaluation criteria and gives methods for design and analysis as a function of the seismic zone and the importance of the structure. An earthquake with a return period of 1 in 50 years is proposed tentatively for the serviceability limit states with appropriate drift limits. The proposed serviceability limit states are shown to govern the design of buildings for values of the force modification factor greater, on average, than 3.Key words: analyses, earthquake, seismic design, serviceability limit state, steel, ultimate limit state.

Sign in / Sign up

Export Citation Format

Share Document