Analysis about Planning and Modification of the Upper and Lower Structures of the 38 Floor Apartment SkyHouse Project with Equivalent Static Analysis

The modeled building structure is a regular building, with the number of levels being varied. The structural model is divided into 38-level portals. This research uses the help of the SAP2000 v21 program to facilitate the earthquake analysis process. The results of the study that will be compared are displacements between levels and base shear that occur due to earthquake forces. The results of the analysis have shown that static analysis produces greater results for the structural models compared to dynamic analysis. The difference in displacement between levels produced by the two methods in the three structural models is still included in the displacement limits between levels of permission required in SNI 1726-2012, so that the three models can still be analyzed by static analysis and dynamic analysis. Because the results of displacement and base shear in static analysis are greater than dynamic analysis, static analysis is safer if used for earthquake force loading in general structural calculations. Although in earthquake analysis, dynamic analysis is a more accurate analysis because the analysis process is closer to the actual situation.

Analysis of Multistory Buildings With Stub Column In Different Seismic Zones In India – A Review

Construction of building requires proper planning and management. Buildings are subjected to various loads such as dead load, live load, wind load and seismic load. Seismic load has extreme adverse effect on building so it is necessary to perform seismic analysis. This paper explains about the response of building when it is subjected to seismic load, this response can be shown by story drift and base shear. Behavior of buildings with stub columns is analyzed and the results are compared with buildings without stub columns. Seismic analysis has been performed on (G+7) buildings located in seismic zones 2,3,4&5 using ETABS software. Analysis has been performed according to IS 1893:PartI (2002).The storey drift and design base shear are evaluated and compared. Pushover analysis was performed and the results were compared.

Shake Table Tests of a Novel Low-rise Bolt-Assembled Precast Concrete Sandwich Wall Panel Structure

A novel low-rise bolt - assembled precast concrete sandwich wall panel structure for rural residential houses was proposed, in which the connections between wall and wall, and wall and floor were connected by high strength bolts and steel plates. The bolt joints can be easily installed and disassembled. They are replaceable to make the precast structure demountable and reassembled. All the components are connected together by the novel bolted connectors. This paper presents the shake-table tests of a full-scale two-story bolt-assembled precast concrete sandwich wall building. The results indicated that the proposed structural system had good seismic performance and remained in the elastic stage with no damage after 9-degree rare earthquake excitation for the Model-1. The Model-2 exhibited excellent capacity and performed satisfactorily under the excitation up to 0.8 g. Cracks were observed at the wall openings and the base of walls and columns, which was similar to that of a cast-in-situ structure. The damage statuses were mainly light damage and moderate damage. The bolt connection joints were not anti-seismic weak places and had good seismic performance. Equivalent base shear method is suitable for estimating the seismic demand of the proposed precast concrete sandwich wall panel structure.

Seismic Performance of RC Column Using Fiber Hinge Concept with Time Integration Method

Recent seismic events showed the importance of understanding the structural performance of RC column that can be predicted numerically. The accuracy of column performance depends on type of the analysis and representation of seismic effect. Therefore, in this paper a nonlinear time history analysis has been performed to assess the seismic performance of bridge column using fiber hinge concept with time integration method using sap2000 software. A long bridge RC column is utilized and subjected to seismic excitation. The column has been divided into different size and numbers of fiber to assess the accuracy of the analysis and time consuming to analyze each case of fiber hinges. In addition, this paper used three-time integration methods, Newmark, Hilber-Hughes-Taylor, and Chung & Hulbert to predict the most suitable method to be used in column seismic analysis. The time history displacement and base shear in addition to moment rotation of the column are the most important factors to evaluate the column seismic performance. The analysis results demonstrated that the most suitable time integration method is Hilber-Hughes-Taylor for such type of the analysis since it gives more stable base shear result than other two methods. Furthermore, the results indicated that the accuracy of seismic performance increased by number of fibers incremental. Moreover, the number of steel fibers should be equal to the number of bars with same area and location. The unconfined and confined concrete should be divided into small areas to get accurate prediction of column seismic performance.

Review on Seismic Analysis of Multistoried Building in Hilly Region

Due to sloping land and high seismically active zones, designing and construction of multistory buildings in hilly regions is always a challenge for structural engineers. This review paper focuses to establish a review study on the Possible Types of building frame configuration in the hilly region and he behavior of Such building frames under seismic loading conditions, and (3) The recent research and developments to make such frames less vulnerable to earthquakes. This paper concludes that the dynamics characteristics of such buildings are significantly different in both horizontal and vertical directions, resulting in the center of mass and center of stiffness having eccentricity at point of action and not vertically aligned for different floors. When such frames are subjected to lateral loads, due to eccentricity it generates torsion in the frame. Most of the studies agree that the buildings resting on slanting ground have higher displacement and base shear compared to buildings resting on plain ground and the shorter column attracts more forces and undergoes damage when subjected to earthquake. Keywords: Building frame configuration, Seismic behavior, Dynamic characteristics, Response spectrum analysis, time history analysis.

Dynamic Behaviour Comparison of an Irregular Edifice with Different Locations of Floating Column and Shear Wall

Architects nowadays develop attractive edifices, and floating columns are widely employed in this process. Floating columns are used not only to provide a magnificent perspective but also when a vast open area is necessary. Edifices with irregular configurations are more vulnerable to earthquakes and hence, suitable shear wall placement is required to ensure the edifice's stability. Many multi-storey edifices collapsed in seconds after the Bhuj Earthquake (Jan 26, 2001), due to the presence of soft stories, floating columns, and mass anomalies. As a result, knowing the seismic reactions of these buildings are vital for constructing earthquake-resistant assemblies. The relevance of a Floating Column and the existence of a shear wall in an irregular multistorey building is highlighted in this study. Dynamic seismic behaviour of a G+18 irregular edifice with different locations of the floating column and different positions of the shear wall is explored in this research. The edifice is analysed and compared with the model without shear walls and floating columns to examine the alterations. The dynamic analysis is carried out using Response Spectrum Analysis and storey drift, storey displacement and base shear are calculated and finally, software compression is computed for different zones. The analysis is carried out by Indian standardized codes IS 1893:2016 and IS 456:2000 which are the codes specified by the Bureau of Indian Standards for earthquake resistance edifice design and plain and reinforcement concrete design respectively. Keywords: Floating Column, Shear Wall, Irregular Edifice, Seismic behaviour, Response Spectrum Analysis, storey drift, storey displacement, base shear.

Quantification of Optimal Target Reliability for Seismic Design: Methodology and Application to Midrise Steel Buildings

Quantification of the optimal target reliability based on the minimum lifecycle cost is the goal standard for calibration of seismic design provisions, which is yet to be fully-materialized even in the leading codes. Deviation from the optimally-calibrated design standards is significantly more pronounced in countries whose regulations are adopted from the few leading codes with no recalibration. A major challenge in the quantification of optimal target reliability for such countries is the lack of risk models that are suited for the local construction industry and design practices. This paper addresses this challenge by presenting an optimal target reliability quantification framework that tailors the available risk models for the countries from which the codes are adopted to the local conditions of the countries adopting the codes. The proposed framework is showcased through the national building code of Iran, which is adopted from the codes of the United States, using a case study of three midrise residential steel building archetypes. The archetypes have various structural systems including intermediate moment-resisting frame (IMF) and special concentrically braced frame (SCBF). Each of these archetypes are designed to different levels of the base shear coefficient, each of which corresponds to a level of reliability. To compute the lifecycle cost, the initial construction cost of buildings is estimated. Next, robust nonlinear models of these structures are generated, using which the probability distribution of structural responses and the collapse fragility are assessed through incremental dynamic analyses. Thereafter, the buildings are subjected to a detailed seismic risk analysis. Subsequently, the lifecycle cost of the buildings is computed as the sum of the initial construction cost and the seismic losses. Finally, the optimal strength and the corresponding target reliability to be prescribed are quantified based on the notion of minimum lifecycle cost. The results reveal a 50-year optimal reliability index of 2.0 and 2.1 for IMF and SCBF buildings, respectively and an optimal collapse probability given the maximum considered earthquake of 16% for both systems. In the context on the case study of the national building code of Iran, the optimal design base shear for IMF buildings is 40% higher than the current prescribed value by the code, whereas that of SCBF buildings is currently at the optimal level.

Effect of Building Configuration on Overstrength Factor and Ductility Factor

It is important for the structure to be economical and still have a high level of life safety. The lateral force sustained by the structures during a large earthquake would be several times larger than the lateral force for which the structures are designed. This is opposite to the fact that design loads such as gravity in codes are usually higher than the actual anticipated load. It is based on the probability that the occurrence of large earthquakes is quite rare and the capacity of the structure to absorb energy. The co-factors of response reduction factor which is the overstrength factor and ductility factor reduce the design horizontal base shear coefficient. A total of 36 low-rise residential buildings having different storey, bay and bay lengths are selected and analysed in this paper. NBC 105: 2020 is selected for the seismic design of RC buildings while provision provided in FEMA 356:2000 is used to carry out non-linear pushover analysis. The results indicated that between the different structures, the value of overstrength factor and ductility factor has a high deviation.

The Behaviour of High-Rise Building with or without Shear Wall under Different Earthquakes

On the 5th June 2015, an earthquake hit Ranau, Sabah with a magnitude of 6.0 that caused 18 casualties and several injuries are one of the examples that show Malaysia is not safe from any seismic event. Most of the structure in Malaysia was designed not to include seismic action. Furthermore, an area that has a high density of population such as in the central region (Klang valley) and several main cities in Malaysia has less available land to build landed housing and uses high-rise apartments as an alternative. High-rise buildings that are normally having problems with soft story mechanisms and plan irregularity which could lead to severe damage when earthquakes happen. This study aims to observe the response of high-rise buildings when under different earthquakes in the presence of shear walls. To achieve this objective two models were modelled and analyzed by using ETABS software, the one with a shear wall and the one with no shear wall. The methods used in this study were the response spectrum method and time-history analysis. In the end, the parameters observed were base shear, story stiffness, story drift, and story displacement. The observations highlighted that the effect of earthquake intensities shows a significant effect. The acquired results indicated that the building with the shear wall is more resistant and strong structures as compared to buildings without shear wall when undergoing seismic analysis.