scholarly journals An analytical method to estimate temperature distribution of typical radiant floor cooling systems with internal heat radiation

2021 ◽  
pp. 014459872199800
Author(s):  
Xiaolong Wang ◽  
Wenke Zhang ◽  
Qingqing Li ◽  
Zhenqiang Wei ◽  
Wenjun Lei ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Internal Heat ◽  
Single Layer ◽  
Heat Radiation ◽  
Transfer Model ◽  
Cooling Systems ◽  
Average Temperature ◽  
Floor Surface ◽  
Floor Structure

Radiant floor cooling systems are increasingly used in practice. The temperature distribution on the floor surface and inside the floor structure, especially the minimum and average temperature of floor surface, determines the thermal performance of radiant floor systems. A good temperature distribution of the floor structure is very important to prevent occupant discomfort and avoid possible condensation in summer cooling. In this study, based on the heat transfer model of the single-layer homogeneous floor structure when there is no internal heat radiation in the room, this paper proposes a heat transfer model of single-layer floor radiant cooling systems when the room has internal heat radiation. Using separation variable methods, an analytical solution was developed to estimate temperature distribution of typical radiant floor cooling systems with internal heat radiation, which can be used to calculate the minimum temperature and the average temperature of typical composite floor structure. The analytical solution was validated by experiments. The values of the measured experiments are in a good agreement with the calculations. The absolute error between the calculated and the measured floor surface temperatures was within 0.45°C. The maximum relative error was within 2.31%. Prove that this model can be accepted. The proposed method can be utilized to calculate the cooling capacity of a typical multi-layer composite floor and will be developed in the future study for design of a typical radiant floor cooling system.

Heat Transfer Model for Pulse Laser Assisted Machining of ZrO2

2016 ◽  
Vol 836-837 ◽  
pp. 430-435
Author(s):  
Huan Lu ◽  
Shu Long Wang ◽  
Ning He ◽  
Liang Li ◽  
Xiu Qing Hao
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Pulse Laser ◽  
Heat Transfer Model ◽  
Simulation Software ◽  
Heat Radiation ◽  
Transfer Model ◽  
Laser Assisted Machining ◽  
Simulated Temperature ◽  
Infrared Temperature Measurement

Laser assisted machining (LAM) is one important solution for machining difficult-to-machine materials. The heat transfer model of quasi steady state in laser assisted micro machining is built, and the simulation software for temperature distribution measurement is developed based on MATLAB. The simulated temperature distribution of the ZrO2 ceramic heated by pulse laser shows a good agreement of tendency with the corresponding experimental results through the infrared temperature measurement method, while the simulated temperature is consistently overestimated. This difference maybe results from the neglect of the heat loss caused by the heat radiation and the heat convection in the model. The proposed model in this paper could provide reference for the selection of optimal process parameters and improve the machining quality, which are closely related to the temperature distribution.

scholarly journals Tank Design for On-Board Hydrogen Storage in Metal Hydrides

2008 ◽  
Author(s):  
Karelle Couturier ◽  
Farida Joppich ◽  
Antje Wo¨rner ◽  
Rainer Tamme
Keyword(s):  
Heat Transfer ◽  
Metal Hydride ◽  
Storage Tank ◽  
Internal Heat ◽  
Transfer Model ◽  
Cooling Fluid ◽  
Internal Heat Exchanger ◽  
Tank Design ◽  
Technical Solutions ◽  
Charging Dynamics

The aim of this work is to reduce the refueling time of a metal hydride storage tank by improving its design, taking in account the total volumetric and mass capacity of the tank. A heat and mass transfer model is proposed and solved to obtain the charging curve for 1 kg hydrogen in a LaNi5 reference storage tank. Compared to gas transport and reaction kinetics, heat transfer is found to limit the hydrogen charging dynamics of the storage tank. To improve the refueling time, it is found to be necessary to increase first of all the heat transfer inside the metal hydride bed, and subsequently the heat transfer from the metal hydride bed to the cooling fluid. Technical solutions such as the implementation of aluminum foam and/or internal heat exchanger tubes are investigated. By combining both solutions, the refueling time can be reduced from 400 minutes (reference tank) to 15 minutes. The tank volume still meets the DOE targets, but its mass remains a problem. Therefore, new materials with improved gravimetric capacity have to be developed. With this work it is now possible to improve the tank design for newly developed storage materials and to evaluate their potential for technical applications.

Correcting Turbocharger Performance Measurements for Heat Transfer and Friction

2017 ◽  
Author(s):  
Mario Schinnerl ◽  
Jan Ehrhard ◽  
Mathias Bogner ◽  
Joerg Seume
Keyword(s):  
Heat Transfer ◽  
Combustion Engine ◽  
Measurement Data ◽  
Internal Heat ◽  
Friction Model ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Friction Power ◽  
Turbine Efficiency ◽  
Compressor Efficiency

The measured performance maps of turbochargers which are commonly used for the matching process with a combustion engine are influenced by heat transfer and friction phenomena. Internal heat transfer from the hot turbine side to the colder compressor side leads to an apparently lower compressor efficiency at low to mid speeds and is not comparable to the compressor efficiency measured under adiabatic conditions. The product of the isentropic turbine efficiency and the mechanical efficiency is typically applied to characterize the turbine efficiency and results from the power balance of the turbocharger. This so-called ‘thermo-mechanical’ turbine efficiency is strongly correlated with the compressor efficiency obtained from measured data. Based on a previously developed one-dimensional heat transfer model, non-dimensional analysis was carried out and a generally valid heat transfer model for the compressor side of different turbochargers was developed. From measurements and ramp-up simulations of turbocharger friction power, an analytical friction power model was developed to correct the thermo-mechanical turbine efficiency from friction impact. The developed heat transfer and friction model demonstrates the capability to properly predict the adiabatic (aerodynamic) compressor and turbine performance from measurement data obtained at a steady-flow hot gas test bench.

Study on Effective Radial Thermal Conductivity of Gas Flow through a Methanol Reactor

2015 ◽  
Vol 13 (1) ◽  
pp. 103-112 ◽  
Author(s):  
Kun Lei ◽  
Hongfang Ma ◽  
Haitao Zhang ◽  
Weiyong Ying ◽  
Dingye Fang
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Temperature Distribution ◽  
Large Scale ◽  
Gas Flow ◽  
Fixed Bed ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Particle Reynolds Number

Abstract The heat conduction performance of the methanol synthesis reactor is significant for the development of large-scale methanol production. The present work has measured the temperature distribution in the fixed bed at air volumetric flow rate 2.4–7 m3 · h−1, inlet air temperature 160–200°C and heating tube temperature 210–270°C. The effective radial thermal conductivity and effective wall heat transfer coefficient were derived based on the steady-state measurements and the two-dimensional heat transfer model. A correlation was proposed based on the experimental data, which related well the Nusselt number and the effective radial thermal conductivity to the particle Reynolds number ranging from 59.2 to 175.8. The heat transfer model combined with the correlation was used to calculate the temperature profiles. A comparison with the predicated temperature and the measurements was illustrated and the results showed that the predication agreed very well with the experimental results. All the absolute values of the relative errors were less than 10%, and the model was verified by experiments. Comparing the correlations of both this work with previously published showed that there are considerable discrepancies among them due to different experimental conditions. The influence of the particle Reynolds number on the temperature distribution inside the bed was also discussed and it was shown that improving particle Reynolds number contributed to enhance heat transfer in the fixed bed.

scholarly journals Group Invariant Solutions for Flow and Heat Transfer of Power-Law Nanofluid in a Porous Medium

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Saba Javaid ◽  
Asim Aziz
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Power Law ◽  
Internal Heat ◽  
Shear Thickening ◽  
Internal Heat Source ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Flow And Heat Transfer ◽  
Power Law Nanofluid

The present work covers the flow and heat transfer model for the power-law nanofluid in the presence of a porous medium over the penetrable plate. The flow is caused by the impulsive movement of the plate embedded in Darcy’s type porous medium. The flow and heat transfer model has been examined with the effect of linear thermal radiation and the internal heat source or sink in the flow regime. The Rosseland approximation is utilized for the optically thick nanofluid. To form the closed-form solutions for the governing partial differential equations of conservation of mass, momentum, and energy, the Lie symmetry analysis is used to get the reductions of governing equations and to find the group invariants. These invariants are then utilized to obtain the exact solution for all three cases, i.e., shear thinning fluid, Newtonian fluid, and shear thickening fluid. In the end, all solutions are plotted for the cu -water nanofluid and discussed briefly for the different emerging flow and heat transfer parameters.

Research on Heat Transfer Characteristics of Nano-Porous Silica Aerogel Material and its Application on Mars Surface Mission

2014 ◽  
Vol 924 ◽  
pp. 329-335 ◽  
Author(s):  
Cong Hang Li ◽  
Shi Chen Jiang ◽  
Zheng Ping Yao ◽  
Song Sheng ◽  
Xin Jian Jiang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Silica Aerogel ◽  
Thermal Environment ◽  
Porous Silica ◽  
Heat Transfer Model ◽  
Heat Radiation ◽  
Transfer Model ◽  
Ambient Conditions ◽  
Coupled Heat Transfer

Based on the nanoporous network structure features of silica aerogel, the gas-solid coupled heat transfer model of silica aerogel is analyzed, and the calculation formulas of the gas-solid coupled, the gas thermal conductivity and the heat radiation within the aerogel are derived. The thermal conductivity of pure silica aerogel is calculated according to the derived heat transfer model and is also experimentally measured. Moreover, measurements on the thermal conductivities of silica aerogel composites with different densities at ambient conditions are performed. And finally, a novel design of silica aerogel based integrated structure and thermal insulation used for withstanding the harsh thermal environment on the Martin surface is presented.

Modeling of Temperature Distribution in Moving Webs in Roll-to-Roll Manufacturing

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Youwei Lu ◽  
Prabhakar R. Pagilla
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Thermal Strain ◽  
Heat Transfer Model ◽  
Operating Conditions ◽  
Transfer Model ◽  
Roll To Roll ◽  
Flexible Material ◽  
Process Line ◽  
The Web

A heat transfer model that can predict the temperature distribution in moving flexible composite materials (webs) for various heating/cooling conditions is developed in this paper. Heat transfer processes are widely employed in roll-to-roll (R2R) machines that are used to perform processing operations, such as printing, coating, embossing, and lamination, on a moving flexible material. The goal is to efficiently transport the webs over heating/cooling rollers and ovens within such processes. One of the key controlled variables in R2R transport is web tension. When webs are heated or cooled during transport, the temperature distribution in the web causes changes in the mechanical and physical material properties and induces thermal strain. Tension behavior is affected by these changes and thermal strain. To determine thermal strain and material property changes, one requires the distribution of temperature in moving webs. A multilayer heat transfer model for composite webs is developed in this paper. Based on this model, temperature distribution in the moving web is obtained for the web transported on a heat transfer roller and in a web span between two adjacent rollers. Boundary conditions that reflect many types of heating/cooling of webs are considered and discussed. Thermal contact resistance between the moving web and heat transfer roller surfaces is considered in the derivation of the heat transfer model. Model simulations are conducted for a section of a production R2R coating and fusion process line, and temperature data from these simulations are compared with measured data obtained at key locations within the process line. In addition to determining thermal strain in moving webs, the model is valuable in the design of heating/cooling sources required to obtain a certain desired temperature at a specific location within the process line. Further, the model can be used in determining temperature dependent parameters and the selection of operating conditions such as web speed.

Specific Absorption Rate and Temperature Increase in Human Eye Subjected to Electromagnetic Fields at 900 MHz

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
Teerapot Wessapan ◽  
Phadungsak Rattanadecho
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Electromagnetic Fields ◽  
Absorption Rate ◽  
Specific Absorption Rate ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Specific Absorption ◽  
Eye Model ◽  
Human Eye

Human eye is one of the most sensitive parts of the entire human body when exposed to electromagnetic fields. These electromagnetic fields interact with the human eye and may lead to cause a variety of ocular effects from high intensity radiation. However, the resulting thermo-physiologic response of the human eye to electromagnetic fields is not well understood. In order to gain insight into the phenomena occurring within the human eye with temperature distribution induced by electromagnetic fields, a detailed knowledge of absorbed power distribution as well as temperature distribution is necessary. This study presents a numerical analysis of specific absorption rate (SAR) and heat transfer in the heterogeneous human eye model exposed to electromagnetic fields. In the heterogeneous human eye model, the effect of power density on specific absorption rate and temperature distribution within the human eye is systematically investigated. In particular, the results calculated from a developed heat transfer model, considered natural convection and porous media theory, are compared with the results obtained from a conventional heat transfer model (based on conduction heat transfer). In all cases, the temperatures obtained from the developed heat transfer model have a lower temperature gradient than that of the conventional heat transfer model. The specific absorption rate and the temperature distribution in various parts of the human eye during exposure to electromagnetic fields at 900 MHz, obtained by numerical solution of electromagnetic wave propagation and heat transfer equation, are also presented. The results show that the developed heat transfer model, which is the more accurate way to determine the temperature increase in the human eye due to electromagnetic energy absorption from electromagnetic field exposure.

Sign in / Sign up

Export Citation Format

Share Document