Optical and Structural Properties of Fluorine Doped SnO2 on Si (100) for Photovoltaic Application

2018 ◽  
Vol 13 (10) ◽  
pp. 1522-1532 ◽  
Author(s):  
S. Nivetha ◽  
K. Kaviyarasu ◽  
A. Ayeshamariam ◽  
N. Punithavelan ◽  
R. Perumalsamy ◽  
...  
Keyword(s):  
Spray Pyrolysis Technique ◽  
Energy Difference ◽  
Vital Role ◽  
X Ray Diffraction ◽  
Energy Storage Devices ◽  
Sem Images ◽  
Storage Devices ◽  
Force Microscopy ◽  
Photovoltaic Application ◽  
Atomic Force

Photovoltaic material plays a vital role in the production of energy storage devices, more specifically in solar cell fabrications. In this work, ITO:F-doped materials were coated over the silicon substrate through spray pyrolysis technique. X-ray diffraction studies were conducted for porous silicon (PSi) coated with ITO:F structures formed at different current densities. This pore formation is evident from the broad peak at 69.9°, revealing an amorphous-like nature but at the same location where the single crystalline peak also is observed. These pores are explicitly shown in the SEM images in which very fine surface fragments are observed. At 20 mA/cm2, well-defined porous patterns that were uniformly distributed over the surface were observed. The microstructures observed via atomic force microscopy for these PSi coated with ITO:F structures are randomly aligned and almost evenly distributed over the entire surface of these nanorods, which are approximately 40 nm. Radiative recombination of electrons from a level in the conduction band or its subband to a level at an energy difference of greater than 1.7 eV in the valance band or its subband will emit visible light.

Structural and mechanical properties of tantalum thin films ected by nitrogen ion implantation

2020 ◽  
Vol 34 (15) ◽  
pp. 2050163 ◽  
Author(s):  
A. H. Ramezani ◽  
S. Hoseinzadeh ◽  
Zh. Ebrahiminejad
Keyword(s):  
Friction Coefficient ◽  
Wear Mechanism ◽  
Mechanism Study ◽  
X Ray Diffraction ◽  
Sem Images ◽  
Force Microscopy ◽  
Atomic Force ◽  
Coefficient Measurement ◽  
Nitrogen Ions ◽  
Nitrogen Ion

Tantalum bulk were implanted with nitrogen ions at different dose of [Formula: see text] ions/cm2 to [Formula: see text] ions/cm2 and at a energy 30 keV. The implanted samples were characterized using X-ray diffraction (XRD), atomic force microscopy (AFM), microhardness testing, friction coefficient measurements and wear mechanism study. Scanning electron microscopy (SEM) images were used to analyze the friction of samples. The XRD results confirmed that the increasing dose affects the formation of the TaN phase. Based on AFM images, the morphology and surface roughness change proportionally to grain size after implantation. It was found that hardness increases as energy increases. From the friction coefficient measurement, this coefficient decreases as energy increases. For the un-implanted sample, the wear mechanism has abrasion, and with increasing the energy, it shifts to being flake and sticky.

Synthesis and Atomic Force Microscopy Contact Current Images of Aluminum Doped ZnO Thin Films

2010 ◽  
Vol 644 ◽  
pp. 109-112
Author(s):  
N. Muñoz Aguirre ◽  
J. Eduardo Rivera-López ◽  
L. Martínez Pérez ◽  
Pedro A. Tamayo Meza
Keyword(s):  
Thin Films ◽  
Atomic Force Microscopy ◽  
Spray Pyrolysis Technique ◽  
Water Mist ◽  
Zno Thin Films ◽  
Electrical Characteristics ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Doped Zno

Aluminum doped ZnO thin films were synthesized by the water-mist assisted spray pyrolysis technique. The structural characterization by means of X-Ray diffraction measurements is reported. By means of Atomic Force Microscopy, the superficial electrical characteristics of the thin films are studied. Specifically, contact current images are shown and discussed. It is important to emphasize that in spite of no voltage is applied to the Atomic Force Microscopy contact conductive tip, current images are getting.

scholarly journals Influence of substrates on the properties of cerium -doped CdO nanocrystalline thin films

2018 ◽  
Vol 16 (38) ◽  
pp. 112-123
Author(s):  
Abubaker S. Mohammed
Keyword(s):  
Thin Films ◽  
Glass Substrate ◽  
Spray Pyrolysis Technique ◽  
Xrd Analysis ◽  
Silicon Substrates ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Cerium Content ◽  
Atomic Force ◽  
Cdo Films

Transparent thin films of CdO:Ce has been deposited on to glass and silicon substrates by spray pyrolysis technique for various concentrations of cerium (2, 4, and 6 Vol.%). CdO:Ce films were characterized using different techniques such as X-ray diffraction (XRD), atomic force microscopy(AFM) and optical properties. XRD analysis show that CdO films exhibit cubic crystal structure with (1 1 1) preferred orientation and the intensity of the peak increases with increasing's of Ce contain when deposited films on glass substrate, while for silicon substrate, the intensity of peaks decreases, the results reveal that the grain size of the prepared thin film is approximately (73.75-109.88) nm various with increased of cerium content. With a surface roughness of (0.871–16.2) nm as well as root mean square of (1.06-19.7) nm for glass substrate, while for silicon (84.79-107.48) nm, for a pure CdO and doped with Ce (2, 4, and 6 Vol.%). The 300-nm-thin CdO films showed that the optical energy band gap equal 2.6 eV, and increases with increasing doping until reaches a maximum value of 3.25 eV when doping levels 6 Vol.%.

scholarly journals Synthesis and characterization of Iron tungstate oxide films by advanced controlled spray pyrolysis technique

2019 ◽  
Vol 17 (41) ◽  
pp. 29-39
Author(s):  
Alaa A. Abdul-hamead
Keyword(s):  
Spray Pyrolysis ◽  
Spray Pyrolysis Technique ◽  
Annealing Treatment ◽  
Tungstic Acid ◽  
Chemical Spray Pyrolysis ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Sensor Applications ◽  
Semiconductor Oxides ◽  
Atomic Force

For the first time Iron tungstate semiconductor oxides films (FeWO4) was successfully synthesized simply by advanced controlled chemical spray pyrolysis technique, via employed double nozzle instead of single nozzle using tungstic acid and iron nitrate solutions at three different compositions and spray separately at same time on heated silicone (n-type) substrate at 600 °C, followed by annealing treatment for one hour at 500 °C. The crystal structure, microstructure and morphology properties of prepared films were studied by X-ray diffraction analysis (XRD), electron Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) respectively. According to characterization techniques, a material of well-crystallized monoclinic phase FeWO4 films with spindle and aggregated fine plates microstructures were obtained from using this advance technique, with thickness about 500 nm. Such these structures have been recognized as one of the most efficient microstructures due to their large specific surface area especially in gas sensor applications.

Study of the elastic properties of sprayed SnO2 and SnS2 layers

2000 ◽  
Vol 77 (9) ◽  
pp. 705-715
Author(s):  
M Mnari ◽  
B Cros ◽  
M Amlouk ◽  
S Belgacem ◽  
D Barjon
Keyword(s):  
High Frequency ◽  
Chemical Structure ◽  
Spray Pyrolysis Technique ◽  
Acoustic Microscopy ◽  
Acoustic Parameters ◽  
Force Microscopy ◽  
Photovoltaic Application ◽  
Atomic Force ◽  
Acoustic Signature ◽  
Acoustic Images

SnO2 and SnS2 thin films have been prepared by the spray pyrolysis technique for photovoltaic application purposes and characterized by high-frequency acoustic microscopy (570 MHz).The surface acoustic images reveal contrasts explained by differences in topography according to atomic force microscopy studies. The acoustic signature V(z) of the systemslayer/substrate were modelled and refined to fit with the experimental V(z). The acoustic parameters of the layers were calculated using the results of the final simulation. The values of Young's modulus deduced from the acoustic parameters, 401 and 56 GPa for SnO2 and SnS2, respectively, are discussed in relation with the chemical structure and bonding involved. PACS Nos.: 43.35Ns and 62.65

Investigation of the Effect of Uv-Assisted Oxidation and Nitridation of Hafnium Metal Films

2003 ◽  
Vol 780 ◽  
Author(s):  
C. Essary ◽  
V. Craciun ◽  
J. M. Howard ◽  
R. K. Singh
Keyword(s):  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Grazing Angle ◽  
X Ray Diffraction ◽  
Metal Thin Films ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force ◽  
Silicon Interface

AbstractHf metal thin films were deposited on Si substrates using a pulsed laser deposition technique in vacuum and in ammonia ambients. The films were then oxidized at 400 °C in 300 Torr of O2. Half the samples were oxidized in the presence of ultraviolet (UV) radiation from a Hg lamp array. X-ray photoelectron spectroscopy, atomic force microscopy, and grazing angle X-ray diffraction were used to compare the crystallinity, roughness, and composition of the films. It has been found that UV radiation causes roughening of the films and also promotes crystallization at lower temperatures.Furthermore, increased silicon oxidation at the interface was noted with the UVirradiated samples and was shown to be in the form of a mixed layer using angle-resolved X-ray photoelectron spectroscopy. Incorporation of nitrogen into the film reduces the oxidation of the silicon interface.

Low Molecular Weight Microfibers with Light Sensing Properties

2017 ◽  
Vol 54 (4) ◽  
pp. 655-658
Author(s):  
Andrei Bejan ◽  
Dragos Peptanariu ◽  
Bogdan Chiricuta ◽  
Elena Bicu ◽  
Dalila Belei
Keyword(s):  
Molecular Weight ◽  
Low Molecular Weight ◽  
X Ray Diffraction ◽  
Aromatic Rings ◽  
X Ray ◽  
Force Microscopy ◽  
Light Sensing ◽  
Sensing Applications ◽  
Atomic Force ◽  
Low Molecular Weight Compounds

Microfibers were obtained from organic low molecular weight compounds based on heteroaromatic and aromatic rings connected by aliphatic spacers. The obtaining of microfibers was proved by scanning electron microscopy. The deciphering of the mechanism of microfiber formation has been elucidated by X-ray diffraction, infrared spectroscopy, and atomic force microscopy measurements. By exciting with light of different wavelength, florescence microscopy revealed a specific optical response, recommending these materials for light sensing applications.

Structural and Optical Properties of InAsSbBi Grown by Molecular Beam Epitaxy on Offcut GaSb Substrates

Photonics ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 215
Author(s):  
Rajeev R. Kosireddy ◽  
Stephen T. Schaefer ◽  
Marko S. Milosavljevic ◽  
Shane R. Johnson
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Optical Quality ◽  
X Ray Diffraction ◽  
Interface Quality ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Lateral Variations

Three InAsSbBi samples are grown by molecular beam epitaxy at 400 °C on GaSb substrates with three different offcuts: (100) on-axis, (100) offcut 1° toward [011], and (100) offcut 4° toward [011]. The samples are investigated using X-ray diffraction, Nomarski optical microscopy, atomic force microscopy, transmission electron microscopy, and photoluminescence spectroscopy. The InAsSbBi layers are 210 nm thick, coherently strained, and show no observable defects. The substrate offcut is not observed to influence the structural and interface quality of the samples. Each sample exhibits small lateral variations in the Bi mole fraction, with the largest variation observed in the on-axis growth. Bismuth rich surface droplet features are observed on all samples. The surface droplets are isotropic on the on-axis sample and elongated along the [011¯] step edges on the 1° and 4° offcut samples. No significant change in optical quality with offcut angle is observed.

scholarly journals Ultrafine metal-polymer catalysts based on polyconjugated systems for Fisher–Tropsch synthesis

2020 ◽  
Vol 92 (6) ◽  
pp. 977-984
Author(s):  
Mayya V. Kulikova ◽  
Albert B. Kulikov ◽  
Alexey E. Kuz’min ◽  
Anton L. Maximov
Keyword(s):  
Tropsch Synthesis ◽  
X Ray Diffraction ◽  
Fischer Tropsch ◽  
Force Microscopy ◽  
Composite Catalysts ◽  
Fe Catalyst ◽  
Atomic Force ◽  
And Function ◽  
Metal Polymer

AbstractFor previously studied Fischer–Tropsch nanosized Fe catalyst slurries, polymer compounds with or without polyconjugating structures are used as precursors to form the catalyst nanomatrix in situ, and several catalytic experiments and X-ray diffraction and atomic force microscopy measurements are performed. The important and different roles of the paraffin molecules in the slurry medium in the formation and function of composite catalysts with the two types of aforementioned polymer matrices are revealed. In the case of the polyconjugated polymers, the alkanes in the medium are “weakly” coordinated with the metal-polymer composites, which does not affect the effectiveness of the polyconjugated polymers. Otherwise, alkane molecules form a “tight” surface layer around the composite particles, which create transport complications for the reagents and products of Fischer-Tropsch synthesis and, in some cases, can change the course of the in situ catalyst formation.

scholarly journals Evaluation of grain boundaries as percolation pathways in quartz-rich continental crust using Atomic Force Microscopy

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ritabrata Dobe ◽  
Anuja Das ◽  
Rabibrata Mukherjee ◽  
Saibal Gupta
Keyword(s):  
Atomic Force Microscopy ◽  
Grain Boundary ◽  
Continental Crust ◽  
Electron Backscatter Diffraction ◽  
Vital Role ◽  
Force Microscopy ◽  
Atomic Force ◽  
Width Measurements ◽  
Lower Temperature ◽  
Backscatter Diffraction

AbstractHydrous fluids play a vital role in the chemical and rheological evolution of ductile, quartz-bearing continental crust, where fluid percolation pathways are controlled by grain boundary domains. In this study, widths of grain boundary domains in seven quartzite samples metamorphosed under varying crustal conditions were investigated using Atomic Force Microscopy (AFM) which allows comparatively easy, high magnification imaging and precise width measurements. It is observed that dynamic recrystallization at higher metamorphic grades is much more efficient at reducing grain boundary widths than at lower temperature conditions. The concept of force-distance spectroscopy, applied to geological samples for the first time, allows qualitative estimation of variations in the strength of grain boundary domains. The strength of grain boundary domains is inferred to be higher in the high grade quartzites, which is supported by Kernel Average Misorientation (KAM) studies using Electron Backscatter Diffraction (EBSD). The results of the study show that quartzites deformed and metamorphosed at higher grades have narrower channels without pores and an abundance of periodically arranged bridges oriented at right angles to the length of the boundary. We conclude that grain boundary domains in quartz-rich rocks are more resistant to fluid percolation in the granulite rather than the greenschist facies.

Sign in / Sign up

Export Citation Format

Share Document