Research on Seismic Control of High Rise Steel Frame Building Structure

2016 ◽  
Vol 13 (12) ◽  
pp. 9898-9903 ◽  
Author(s):  
Fengmei Pi ◽  
Zhiyuan Liu ◽  
Hongwei Yang
Keyword(s):  
Steel Frame ◽  
Building Structure ◽  
Seismic Control ◽  
High Rise ◽  
Frame Building

Automation of seismic design of high-rise structure with braced steel frame

2021 ◽  
Author(s):  
Xin Zhao ◽  
Gang Wang ◽  
Jinlun Cai ◽  
Junchen Guo
Keyword(s):  
Seismic Performance ◽  
Seismic Design ◽  
Structural Design ◽  
Structure Design ◽  
Steel Frame ◽  
Design Methods ◽  
Automatic Design ◽  
Component Level ◽  
Design Algorithm ◽  
High Rise

<p>With the continuous development and progress of society, the structure of high-rise buildings has been paid more and more attention by the engineering community. However, the existing high- rise structure design methods often have a lot of redundancy and have a lot of room for optimization. Most of the existing seismic design methods of high-rise structures are based on engineering experience and manual iterative methods, so that the efficiency of design can not meet the needs of the society. if the method of design automation is adopted, the workload of designers can be greatly reduced and the efficiency of structural design can be improved. Based on the digital modeling theory, this paper proposes a MAD automatic design algorithm, in which the designer provides the initial design of the structure, and the algorithm carries out the modeling, analysis, optimization and design of each stage of the structure, and finally obtains the optimal structure. The structural design module of this algorithm starts from the component level, when the component constraint design meets the limit requirements of the specification, it enters and completes the component constraint design and the global constraint design of the structure in turn. In this paper, taking a ten-story braced steel frame high-rise structure as an example, the optimal design is carried out, and its seismic performance is analyzed. the results show that the MAD automatic design algorithm can distribute the materials to each part reasonably, which can significantly improve the seismic performance of the structure and realize the effective seismic design.</p>

Linear and non-linear analysis on two-dimensional steel frame under different temperatures

2019 ◽  
Vol 10 (1) ◽  
pp. 48-55
Author(s):  
Parthasarathi N. ◽  
Satyanarayanan K.S. ◽  
Prakash M. ◽  
Thamilarasu V.
Keyword(s):  
High Temperatures ◽  
Progressive Collapse ◽  
Transient State ◽  
Steel Frame ◽  
Frame Structure ◽  
Two Dimensional ◽  
Content Type ◽  
Frame Building ◽  
Different Temperatures ◽  
Steel Frame Structure

Purpose Progressive collapse because of high temperatures arising from an explosion, vehicle impact or fire is an important issue for structural failure in high-rise buildings. Design/methodology/approach The present study, using ABAQUS software for the analysis, investigated the progressive collapse of a two-dimensional, three-bay, four-storey steel frame structure from high-temperature stresses. Findings After structure reaches the temperature results like displacement, stress axial load and shear force are discussed. Research limitations/implications Different temperatures were applied to the columns at different heights of a structure framed with various materials. Progressive collapse load combinations were also applied as per general service administration guidelines. Originality/value This study covered both steady-state and transient-state conditions of a multistorey-frame building subjected to a rise in temperature in the corner columns and intermediate columns. The columns in the framed structure were subjected to high temperatures at different heights, and the resulting displacements, stresses and axial loads were obtained, analysed and discussed.

scholarly journals SEISMIC ANALYSIS OF MULTISTORIED IRREGULAR AND REGULAR BUILDING WITH MASONARY INFILLS

2021 ◽  
Vol 5 (12) ◽  
Author(s):  
Ashutosh Shrivastava ◽  
Rajesh Chaturvedi
Keyword(s):  
Urban Areas ◽  
Seismic Analysis ◽  
Response Spectrum ◽  
Pushover Analysis ◽  
Seismic Zone ◽  
Soft Storey ◽  
High Rise ◽  
Frame Building ◽  
Performance Point ◽  
Open Ground

Nowadays, as in the urban areas the space available for the construction of buildings is limited. So in limited space we have to construct such type of buildings which can be used for multiple purposes such as lobbies, car parking etc. To fulfill this demand, high rise buildings is the only option available. The performance of a high rise building during strong earthquake motion depends on the distribution of stiffness, strength and mass along both the vertical and horizontal directions. If there is discontinuity in stiffness, strength and mass between adjoining storeys of a building then such a building is known as irregular building. The present study focuses on the seismic performance of regular and vertical irregular building with and without masonary infills. In the present study G+11 building is considered for the analysis with modelling and analysis done on ETABS software v17.0.1. The earthquake forces are calculated as per IS 1893 (part 1): 2016 for seismic zone III. The width of strut is calculated by using equivalent diagonal strut method. Total five models are considered for the analysis i.e. regular building with bare frame, regular building with masonary infill, soft storey building with open ground storey, mass irregular building with masonary infill and vertical geometric irregular building with masonary infill. The non-linear static analysis (pushover analysis) and linear dynamic analysis (response spectrum analysis) are performed for all the models and thereby compare their results. From analysis, the parameters like performance point, time period, maximum storey displacement, maximum storey drifts, storey shears and overturning moments are determined and also comparative study is done for all the models. From the comparison, it is observed that the vertical geometric irregular building shows better performance under seismic loading and bare frame building shows inferior performance. Moreover, the performance of masonary infilled frame building is f

scholarly journals HIGH RISE FRAME BUILDING CONSTRUCTION WITH REGARD TO DEFECTS IN MONOLITHIC BASE SLAB

2020 ◽  
Vol 22 (5) ◽  
pp. 160-172
Author(s):  
S. V. Yushchube ◽  
I. I. Podshivalov ◽  
G. I. Tayukin
Keyword(s):  
Defect Formation ◽  
Strength Properties ◽  
Building Construction ◽  
Non Destructive Testing ◽  
Destructive Testing ◽  
High Rise ◽  
Frame Building ◽  
Concrete Layer ◽  
Non Destructive

The paper analyzes the influence of defects detected in a monolithic base slab on the possibility of its further application in the construction of a 25-storey high-rise frame building. Non destructive testing and vertical core sampling techniques are used for the detailed analysis of the monolithic base slab. It is found that irregularities in the procedure during winter concreting of the base slab decreases the strength properties of concrete and provides the defect formation in the slab structure, namely delamination of the lower protective concrete layer and uncovering of working reinforcement. For the safe use of the 25-storey high-rise building, the base slab is proposed to be strengthened by adding in-situ reinforced concrete layer 100 cm thick.

Sign in / Sign up

Export Citation Format

Share Document