Horny Layer Thickness as Assessed Functionally Does Not Predict Sodium Lauryl Sulphate Skin Irritation

2015 ◽  
pp. 176-179 ◽  
Author(s):  
G. Zarafonitis ◽  
P. G. M. van der Valk
Keyword(s):  
Layer Thickness ◽  
Skin Irritation ◽  
Sodium Lauryl Sulphate ◽  
Horny Layer

Different skin irritation abilities of different qualities of sodium lauryl sulphate

1989 ◽  
Vol 21 (3) ◽  
pp. 184-188 ◽  
Author(s):  
Tove Agner ◽  
Jørgen Serup ◽  
Vagn Handlos ◽  
Walther Batsberg
Keyword(s):  
Skin Irritation ◽  
Sodium Lauryl Sulphate

Proteomic analysis of skin irritation reveals the induction of HSP27 by sodium lauryl sulphate in human skin

2002 ◽  
Vol 146 (5) ◽  
pp. 777-785 ◽  
Author(s):  
I.L.A. Boxman ◽  
P.J. Hensbergen ◽  
R.C. Van Der Schors ◽  
D.P. Bruynzeel ◽  
C.P. Tensen ◽  
...  
Keyword(s):  
Human Skin ◽  
Proteomic Analysis ◽  
Skin Irritation ◽  
Sodium Lauryl Sulphate

Structure and Orientation of As Precipitates in LT-MBE Grown GaAs

1991 ◽  
Vol 49 ◽  
pp. 900-901 ◽  
Author(s):  
Alain Claverie ◽  
Zuzanna Liliental-Weber
Keyword(s):  
Transport Properties ◽  
Layer Thickness ◽  
Growth Temperature ◽  
Low Temperatures ◽  
Lattice Parameter ◽  
Crystalline Quality ◽  
Insulating Properties ◽  
Lt Gaas

GaAs layers grown by MBE at low temperatures (in the 200°C range, LT-GaAs) have been reported to have very interesting electronic and transport properties. Previous studies have shown that, before annealing, the crystalline quality of the layers is related to the growth temperature. Lowering the temperature or increasing the layer thickness generally results in some columnar polycrystalline growth. For the best “temperature-thickness” combinations, the layers may be very As rich (up to 1.25%) resulting in an up to 0.15% increase of the lattice parameter, consistent with the excess As. Only after annealing are the technologically important semi-insulating properties of these layers observed. When annealed in As atmosphere at about 600°C a decrease of the lattice parameter to the substrate value is observed. TEM studies show formation of precipitates which are supposed to be As related since the average As concentration remains almost unchanged upon annealing.

Paracrystalline Aggregates of Psoriatic Keratin and Their Relation to Normal Keratin Structure

1985 ◽  
Vol 43 ◽  
pp. 680-681
Author(s):  
S. Trachtenberg ◽  
P.M. Steinert ◽  
B.L. Trus ◽  
A.C. Steven
Keyword(s):  
Cell Death ◽  
Stratum Corneum ◽  
Intermediate Filament ◽  
Skin Disease ◽  
Amorphous Matrix ◽  
Terminal Differentiation ◽  
Proteolytic Degradation ◽  
Horny Layer ◽  
Chronic Skin ◽  
Chronic Skin Disease

During terminal differentiation of vertebrate epidermis, certain specific keratin intermediate filament (KIF) proteins are produced. Keratinization of the epidermis involves cell death and disruption of the cytoplasm, leaving a network of KIF embedded in an amorphous matrix which forms the outer horny layer known as the stratum corneum. Eventually these cells are shed (desquamation). Normally, the processes of differentiation, keratinization, and desquamation are regulated in an orderly manner. In psoriasis, a chronic skin disease, a hyperkeratotic stratum corneum is produced, resulting in abnormal desquamation of unusually large scales. In this disease, the normal KIF proteins are diminished in amount or absent, and other proteins more typical of proliferative epidermal cells are present. There is also evidence of proteolytic degradation of the KIF.

The stabilization of B.C.C. Cu in Cu/Nb nanolayered composites

1996 ◽  
Vol 54 ◽  
pp. 228-229
Author(s):  
H. Kung ◽  
A.J. Griffin ◽  
Y.C. Lu ◽  
K.E. Sickafus ◽  
T.E. Mitchell ◽  
...  
Keyword(s):  
Electrical Resistivity ◽  
Layer Thickness ◽  
Volume Fraction ◽  
Ion Beam ◽  
High Strength ◽  
Cross Sectional ◽  
Metastable Structure ◽  
High Resolution Tem ◽  
Potential Improvement ◽  
Two Phases

Materials with compositionally modulated structures have gained much attention recently due to potential improvement in electrical, magnetic and mechanical properties. Specifically, Cu-Nb laminate systems have been extensively studied mainly due to the combination of high strength, and superior thermal and electrical conductivity that can be obtained and optimized for the different applications. The effect of layer thickness on the hardness, residual stress and electrical resistivity has been investigated. In general, increases in hardness and electrical resistivity have been observed with decreasing layer thickness. In addition, reduction in structural scale has caused the formation of a metastable structure which exhibits uniquely different properties. In this study, we report the formation of b.c.c. Cu in highly textured Cu/Nb nanolayers. A series of Cu/Nb nanolayered films, with alternating Cu and Nb layers, were prepared by dc magnetron sputtering onto Si {100} wafers. The nominal total thickness of each layered film was 1 μm. The layer thickness was varied between 1 nm and 500 nm with the volume fraction of the two phases kept constant at 50%. The deposition rates and film densities were determined through a combination of profilometry and ion beam analysis techniques. Cross-sectional transmission electron microscopy (XTEM) was used to examine the structure, phase and grain size distribution of the as-sputtered films. A JEOL 3000F high resolution TEM was used to characterize the microstructure.

On the Effect of 2-Layer Thickness by High-Specific Gravity Armor Blocks on Wave Reflection

1999 ◽  
Author(s):  
Masahiro Ito ◽  
Yuitch Iwagaki ◽  
Hiroshi Murakami ◽  
Kenji Nemoto ◽  
Masato Yamamoto ◽  
...  
Keyword(s):  
Specific Gravity ◽  
Layer Thickness ◽  
Wave Reflection ◽  
High Specific Gravity
Sign in / Sign up

Export Citation Format

Share Document