scholarly journals Microfluidic Device Control System Based on Segmented Temperature Sensor

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Anlin Xu ◽  
Ping Li
Keyword(s):  
Microfluidic Device ◽  
Indium Tin Oxide ◽  
Temperature Sensor ◽  
Biochemical Analysis ◽  
Simple Structure ◽  
Low Cost ◽  
Channel Structure ◽  
Measuring Device ◽  
Proportional Integral Derivative Control ◽  
Low Dimensional

Microfluidic technology refers to the technique of controlling the flow, mass transfer, and heat transfer of a fluid with a volume of picoliter to nanoliter in a low-dimensional channel structure with at least one dimension of micron or even nanometer scale. It is widely used in biochemical analysis, immunity, minimally invasive surgery, and environmental monitoring. This paper proposes a microfluidic device based on a segmented temperature sensor. This device can be used for segmental temperature measurement and controlling the temperature of the solution in the microchannel of a glass microfluidic chip. The device is based on a transparent indium tin oxide film glass as a heating element. It adopts a temperature control platform of a proportional-integral-derivative control algorithm. The system uses a charged coupled device camera, a fluorescence microscope, and an image acquisition card to form a noncontact fluorescent indicator temperature measuring device. The device measures the temperature distribution of the microfluid space with time and controls the microfluidics. Moreover, the device has the advantages of simple structure, low cost, and convenient operation.

The Liquid Level Measuring Device in Truck Based on ZigBee

2012 ◽  
Vol 562-564 ◽  
pp. 2002-2006
Author(s):  
Hai Bo Lin ◽  
Ji Xin Zhou ◽  
Hui Cao ◽  
Nian Teng Feng ◽  
Chui Jie Yi
Keyword(s):  
High Precision ◽  
Simple Structure ◽  
Low Cost ◽  
Correction Method ◽  
Liquid Level ◽  
Wireless Data ◽  
Measuring Device ◽  
Zigbee Technology

Because of the separation of modified truck’s cab and car tank, there must set long wires to transmit the signal. A liquid level measuring device for truck is designed and developed in this article. Using the ZigBee technology, a wireless data transmit mode, including the hardware and the software, is realized. A compensation and correction method is discussed on the basis of the ultrasonic transmission theory. This device has a simple structure, high precision, low cost, easy to install and so on.

Fabrication of 3D Temperature Sensor Using Magnetostrictive Inkjet Printhead

2020 ◽  
Vol 64 (5) ◽  
pp. 50405-1-50405-5
Author(s):  
Young-Woo Park ◽  
Myounggyu Noh
Keyword(s):  
Flexible Electronics ◽  
Inkjet Printing ◽  
Temperature Sensor ◽  
Computer Aided Design ◽  
Low Cost ◽  
Three Dimensional ◽  
Drop On Demand ◽  
Aided Design ◽  
Nanoparticle Ink ◽  
Inkjet Printhead

Abstract Recently, the three-dimensional (3D) printing technique has attracted much attention for creating objects of arbitrary shape and manufacturing. For the first time, in this work, we present the fabrication of an inkjet printed low-cost 3D temperature sensor on a 3D-shaped thermoplastic substrate suitable for packaging, flexible electronics, and other printed applications. The design, fabrication, and testing of a 3D printed temperature sensor are presented. The sensor pattern is designed using a computer-aided design program and fabricated by drop-on-demand inkjet printing using a magnetostrictive inkjet printhead at room temperature. The sensor pattern is printed using commercially available conductive silver nanoparticle ink. A moving speed of 90 mm/min is chosen to print the sensor pattern. The inkjet printed temperature sensor is demonstrated, and it is characterized by good electrical properties, exhibiting good sensitivity and linearity. The results indicate that 3D inkjet printing technology may have great potential for applications in sensor fabrication.

scholarly journals Design and Manufacturing of a Disposable, Cyclo-Olefin Copolymer, Microfluidic Device for a Biosensor †

Sensors ◽  
2019 ◽  
Vol 19 (5) ◽  
pp. 1178 ◽  
Author(s):  
Jorge Prada ◽  
Christina Cordes ◽  
Carsten Harms ◽  
Walter Lang
Keyword(s):  
Microfluidic Device ◽  
Heating Temperature ◽  
Low Cost ◽  
Reaction Chamber ◽  
Microfluidic System ◽  
Heating Process ◽  
Design And Manufacturing ◽  
On Chip ◽  
Working Parameters ◽  
Auto Fluorescence

This contribution outlines the design and manufacturing of a microfluidic device implemented as a biosensor for retrieval and detection of bacteria RNA. The device is fully made of Cyclo-Olefin Copolymer (COC), which features low auto-fluorescence, biocompatibility and manufacturability by hot-embossing. The RNA retrieval was carried on after bacteria heat-lysis by an on-chip micro-heater, whose function was characterized at different working parameters. Carbon resistive temperature sensors were tested, characterized and printed on the biochip sealing film to monitor the heating process. Off-chip and on-chip processed RNA were hybridized with capture probes on the reaction chamber surface and identification was achieved by detection of fluorescence tags. The application of the mentioned techniques and materials proved to allow the development of low-cost, disposable albeit multi-functional microfluidic system, performing heating, temperature sensing and chemical reaction processes in the same device. By proving its effectiveness, this device contributes a reference to show the integration potential of fully thermoplastic devices in biosensor systems.

scholarly journals Room-Temperature Solution-Processed 0D/1D Bilayer Electrodes for Translucent CsPbBr3 Perovskite Photovoltaics

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1489
Author(s):  
Bhaskar Parida ◽  
Saemon Yoon ◽  
Dong-Won Kang
Keyword(s):  
Solar Cells ◽  
Indium Tin Oxide ◽  
High Performance ◽  
Room Temperature ◽  
Low Cost ◽  
Perovskite Solar Cells ◽  
Ambient Air ◽  
Plasma Damage ◽  
Temperature Solution ◽  
Ito Nanoparticles

Materials and processing of transparent electrodes (TEs) are key factors to creating high-performance translucent perovskite solar cells. To date, sputtered indium tin oxide (ITO) has been a general option for a rear TE of translucent solar cells. However, it requires a rather high cost due to vacuum process and also typically causes plasma damage to the underlying layer. Therefore, we introduced TE based on ITO nanoparticles (ITO-NPs) by solution processing in ambient air without any heat treatment. As it reveals insufficient conductivity, Ag nanowires (Ag-NWs) are additionally coated. The ITO-NPs/Ag-NW (0D/1D) bilayer TE exhibits a better figure of merit than sputtered ITO. After constructing CsPbBr3 perovskite solar cells, the device with 0D/1D TE offers similar average visible transmission with the cells with sputtered ITO. More interestingly, the power conversion efficiency of 0D/1D TE device was 5.64%, which outperforms the cell (4.14%) made with sputtered-ITO. These impressive findings could open up a new pathway for the development of low-cost, translucent solar cells with quick processing under ambient air at room temperature.

scholarly journals Microsphere-Based Microfluidic Device for Plasma Separation and Potential Biochemistry Analysis Applications

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 487
Author(s):  
Hongyan Xu ◽  
Zhangying Wu ◽  
Jinan Deng ◽  
Jun Qiu ◽  
Ning Hu ◽  
...  
Keyword(s):  
Blood Sample ◽  
Microfluidic Device ◽  
Biochemical Analysis ◽  
Cost Effective ◽  
Clinical Diagnostics ◽  
Correction Factors ◽  
Separation Device ◽  
Blood Samples ◽  
Plasma Separation ◽  
Blood Biochemical

The development of a simple, portable, and cost-effective plasma separation platform for blood biochemical analysis is of great interest in clinical diagnostics. We represent a plasma separation microfluidic device using microspheres with different sizes as the separation barrier. This plasma separation device, with 18 capillary microchannels, can extract about 3 μL of plasma from a 50 μL blood sample in about 55 min. The effects of evaporation and the microsphere barrier on the plasma biochemical analysis results were studied. Correction factors were applied to compensate for these two effects. The feasibility of the device in plasma biochemical analysis was validated with clinical blood samples.

scholarly journals Negative Pressure Provides Simple and Stable Droplet Generation in a Flow-Focusing Microfluidic Device

Micromachines ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 662
Author(s):  
Nikita A. Filatov ◽  
Anatoly A. Evstrapov ◽  
Anton S. Bukatin
Keyword(s):  
Microfluidic Device ◽  
Negative Pressure ◽  
Low Cost ◽  
Control Valve ◽  
Droplet Microfluidics ◽  
Droplet Generation ◽  
Electric Signal ◽  
Absolute Pressure ◽  
Flow Focusing ◽  
Wide Range

Droplet microfluidics is an extremely useful and powerful tool for industrial, environmental, and biotechnological applications, due to advantages such as the small volume of reagents required, ultrahigh-throughput, precise control, and independent manipulations of each droplet. For the generation of monodisperse water-in-oil droplets, usually T-junction and flow-focusing microfluidic devices connected to syringe pumps or pressure controllers are used. Here, we investigated droplet-generation regimes in a flow-focusing microfluidic device induced by the negative pressure in the outlet reservoir, generated by a low-cost mini diaphragm vacuum pump. During the study, we compared two ways of adjusting the negative pressure using a compact electro-pneumatic regulator and a manual airflow control valve. The results showed that both types of regulators are suitable for the stable generation of monodisperse droplets for at least 4 h, with variations in diameter less than 1 µm. Droplet diameters at high levels of negative pressure were mainly determined by the hydrodynamic resistances of the inlet microchannels, although the absolute pressure value defined the generation frequency; however, the electro-pneumatic regulator is preferable and convenient for the accurate control of the pressure by an external electric signal, providing more stable pressure, and a wide range of droplet diameters and generation frequencies. The method of droplet generation suggested here is a simple, stable, reliable, and portable way of high-throughput production of relatively large volumes of monodisperse emulsions for biomedical applications.

scholarly journals Direct measurement of the thermoelectric properties of electrochemically deposited Bi2Te3 thin films

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Jose Recatala-Gomez ◽  
Pawan Kumar ◽  
Ady Suwardi ◽  
Anas Abutaha ◽  
Iris Nandhakumar ◽  
...  
Keyword(s):  
Thin Films ◽  
Thermoelectric Properties ◽  
Bismuth Telluride ◽  
Indium Tin Oxide ◽  
Seed Layer ◽  
Room Temperature ◽  
Low Cost ◽  
Temperature Dependent ◽  
Temperature Heat ◽  
Electrochemically Deposited

Abstract The best known thermoelectric material for near room temperature heat-to-electricity conversion is bismuth telluride. Amongst the possible fabrication techniques, electrodeposition has attracted attention due to its simplicity and low cost. However, the measurement of the thermoelectric properties of electrodeposited films is challenging because of the conducting seed layer underneath the film. Here, we develop a method to directly measure the thermoelectric properties of electrodeposited bismuth telluride thin films, grown on indium tin oxide. Using this technique, the temperature dependent thermoelectric properties (Seebeck coefficient and electrical conductivity) of electrodeposited thin films have been measured down to 100 K. A parallel resistor model is employed to discern the signal of the film from the signal of the seed layer and the data are carefully analysed and contextualized with literature. Our analysis demonstrates that the thermoelectric properties of electrodeposited films can be accurately evaluated without inflicting any damage to the films.

scholarly journals Investigation of serial coherent laser beam combination based on Brillouin amplification

2007 ◽  
Vol 25 (1) ◽  
pp. 79-83 ◽  
Author(s):  
SHUANGYI WANG ◽  
ZHIWEI LÜ ◽  
DIANYANG LIN ◽  
LEI DING ◽  
DONGBIN JIANG
Keyword(s):  
Laser Beam ◽  
High Power ◽  
Simple Structure ◽  
Low Cost ◽  
Coupling Efficiency ◽  
Laser Beams ◽  
Beam Combination ◽  
Multiple Beams ◽  
Combination Scheme ◽  
Stokes Beam

Based on transferring energy from multiple pump beams into one Stokes beam using Brillouin amplification, a serial coherent laser beam combination scheme is presented, which has many advantages, such as, simple structure, low cost, ease of adjustment, higher load capability, scalable easily, etc. Furthermore, it has been demonstrated that the combination of several beams using this method is theoretically possible. But in practice, the amplification of high power Stokes beam is a key problem to solve. In this paper, the amplification of Stokes beam whose power is higher than the pump beam is first studied and proved experimentally. Coupling the two laser beams by this method is proved experimentally, and the coupling efficiency reaches more than 80%. Then the feasibility of multiple beams combination based on Brillouin amplification is analyzed and tested theoretically.

A low-cost thin layer coulometric microfluidic device based on an ion-selective membrane for calcium determination

The Analyst ◽  
2014 ◽  
Vol 139 (1) ◽  
pp. 48-51 ◽  
Author(s):  
Denis Dorokhin ◽  
Gastón A. Crespo ◽  
Majid Ghahraman Afshar ◽  
Eric Bakker
Keyword(s):  
Thin Layer ◽  
Microfluidic Device ◽  
Low Cost ◽  
Selective Membrane ◽  
Calcium Determination

Compact Triple/Quadruple-Band Reconfigurable Monopole Antenna for Wireless Applications

2021 ◽  
pp. 2150277
Author(s):  
Asmaa Zugari ◽  
Wael Abd Ellatif Ali ◽  
Mohammad Ahmad Salamin ◽  
El Mokhtar Hamham
Keyword(s):  
Simple Structure ◽  
Low Cost ◽  
Ground Plane ◽  
Monopole Antenna ◽  
Pin Diode ◽  
Wireless Applications ◽  
Rectangular Patch ◽  
Antenna Performance ◽  
Compact Size ◽  
Multi Band

In this paper, a compact reconfigurable tri-band/quad-band monopole antenna is presented. To achieve the multi-band behavior, two right-angled triangles were etched in a conventional rectangular patch, and a partial ground plane is used. Moreover, the proposed multi-band antenna is printed on a low cost FR4 epoxy with compact dimensions of 0.23[Formula: see text], where [Formula: see text] is calculated at the lowest resonance frequency. To provide frequency agility, a metal strip which acts as PIN diode was embedded in the frame of the modified patch. The tri-band/quad-band antenna performance in terms of reflection coefficient, radiation patterns, peak gain and efficiency was studied. The measured results are consistent with the simulated results for both cases. The simple structure and the compact size of the proposed antenna could make it a good candidate for multi-band wireless applications.

Sign in / Sign up

Export Citation Format

Share Document