scholarly journals Adsorption Performance of La(III) and Y(III) on Orange Peel: Impact of Experimental Variables, Isotherms, and Kinetics

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Li Liu ◽  
Yunzhang Rao ◽  
Changshun Tian ◽  
Tao Huang ◽  
Jiacheng Lu ◽  
...  
Keyword(s):  
Adsorption Process ◽  
Chemical Interaction ◽  
Orange Peel ◽  
Ion Concentration ◽  
Batch Adsorption ◽  
Order Model ◽  
Adsorption Performance ◽  
Monolayer Adsorption ◽  
Langmuir Isotherm Model ◽  
Better Than

To alleviate the environmental problem associated with rare earth wastewater, this research applied waste orange peel (OP) for the adsorption of La(III) and Y(III) from aqueous solution. The adsorption properties of orange peel are characterized using scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR), and the participation of hydroxyl and other oxygen-containing groups that promote the physical-chemical interaction is verified. Batch adsorption results suggest that orange peel possesses a satisfactory adsorption performance for La(III) and Y(III). The optimal adsorption conditions were obtained at pH of 6, temperature of 40°C, appropriate dosage of 2 g/L and 3 g/L, contact time of 30 min, and initial ion concentration of 32 mg/L. Under the same condition, adsorption performance of La(III) is better than that of Y(III). The experimental data is well fitted by the Langmuir isotherm model with correlation   coefficient   R 2 > 0.9 and the minimum standard error values. Equilibrium results show that Langmuir monolayer adsorption capacity of La(III) and Y(III) onto orange peel is up to 37.61 and 31.10 mg/g. The fitting results of kinetics prove that the adsorption process of La(III) and Y(III) follows the pseudosecond-order model. Thus, natural orange peel as a recyclable biosorbent has potential economic and applicative benefits to remove La(III) and Y(III) from aqueous solutions.

scholarly journals Removal of Cadmium(II) from Water using Modified Citrus limettioides Peels: Thermodynamic and Isotherm Studies

2019 ◽  
Vol 32 (1) ◽  
pp. 73-78
Author(s):  
P. Janaki ◽  
R. Sudha ◽  
T.S. Sribharathi ◽  
P. Anitha ◽  
K. Poornima ◽  
...  
Keyword(s):  
Adsorption Process ◽  
Low Cost ◽  
Raw Material ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Adsorption Method ◽  
Chemically Modified ◽  
Adsorption Performance ◽  
Monolayer Adsorption ◽  
Isotherm Equations

The adsorption performance of sulphuric acid treated low cost adsorbent synthesized by using Citrus limettioides peel as an effective raw material for the removal of cadmium(II) from water. The batch adsorption method was carried out to optimize some parameters like contact time, pH and adsorbent dose. The nonlinear isotherm equations were used to calculate the different isotherm constant of five isotherm models namely Freundlich, Langmuir, Dubinin-Radushkevich, Redlich-Peterson and Sips. The Langmuir monolayer adsorption capacity of chemically modified Citrus limettioides peel was found to be 287.60 mg g-1. The negative values of ΔGº and ΔHº showed that the adsorption process is spontaneous and exothermic.

Adsorption of Ni(II) Ion onto Calcined Eggshells: A Study of Equilibrium Adsorption Isotherm

2019 ◽  
Vol 19 (1) ◽  
pp. 143
Author(s):  
Hans Kristianto ◽  
Novitri Daulay ◽  
Arenst Andreas Arie
Keyword(s):  
Adsorption Process ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Sem Images ◽  
Economical Method ◽  
X Ray ◽  
Adsorption Performance ◽  
Monolayer Adsorption ◽  
Equilibrium Adsorption Isotherm

Adsorption is one of the most effective and economical method to treat heavy metals in water. In this study, we utilize waste chicken eggshells as biosorbent to adsorb Ni(II). Furthermore we study the effect of eggshell calcination on its adsorption performance. The effect of calcination on the characteristic of eggshell was observed using Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscope-Energy Dispersive X-ray Spectroscopy (SEM-EDS). It could be observed that CaCO3 in eggshell was converted into CaO, and from SEM images the calcined eggshell became more porous than the uncalcined one. The effect of various parameters such as initial Ni(II) solution pH and initial Ni(II) concentration was investigated using batch adsorption experiments. The data obtained then fitted to Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherms. The best pH for Ni(II) adsorption was found to be 6. From Langmuir and Dubinin-Radushkevich, it was found that calcined eggshells gave 60 times higher maximum adsorption capacity then uncalcined one. This increase was possible due to more porous structure of calcined eggshells. The adsorption process was found to be exothermic and physisorption. This result was confirmed by the decrease of % removal with increase of temperature. Furthermore, Langmuir isotherm was found to be the best model, indicating adsorption of Ni(II) was monolayer adsorption on homogenous surface.

scholarly journals Removal of aqueous Cr(VI) by magnetic biochar derived from bagasse

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Meina Liang ◽  
Yanmei Ding ◽  
Qing Zhang ◽  
Dunqiu Wang ◽  
Huanhuan Li ◽  
...  
Keyword(s):  
Adsorption Process ◽  
Amorphous Structure ◽  
Batch Adsorption ◽  
High Adsorption ◽  
Magnetic Biochar ◽  
Adsorption Performance ◽  
Monolayer Adsorption ◽  
Before And After ◽  
Pseudo Second Order ◽  
Cr Concentration

AbstractWe prepared a novel adsorbent functionalized by bagasse magnetic biochar (BMBC). To study the removal behaviors and mechanisms of Cr(VI) by BMBC, batch adsorption experiments were conducted by modifying variables, such as pH, adsorption time, BMBC dosages, initial Cr concentration, co-existing ions, and ionic strength, and characterizing BMBC before and after Cr(VI) adsorption. BMBC was primarily composed of Fe2O3 and Fe3O4 on bagasse boichar with an amorphous structure. The specific surface area of BMBC was 81.94 m2 g−1, and the pHpzc of BMBC was 6.2. The fabricated BMBC showed high adsorption performance of Cr(VI) in aqueous solution. The maximum Cr(VI) adsorption capacity of BMBC was 29.08 mg g−1 at 25 ºC, which was much higher than that of conventional biochar sorbents. The adsorption process followed pseudo-second-order kinetics and could be explained by the involvement of the Langmuir isotherm in monolayer adsorption. The crystalline structure of Fe3O4 in the BMBC changed slightly during the adsorption process; Fe3O4 improved the adsorption of Cr(VI) on BMB. The desorption capacity of Cr(VI) was 8.21 mg g−1 when 0.2 mol L−1 NaOH was used as the desorption solution. After being reused three times, the removal efficiency is still as high as 80.36%.

scholarly journals Sequestration of Pb(II) and Ni(II) ions from aqueous solution using microalga Rhizoclonium hookeri: adsorption thermodynamics, kinetics, and equilibrium studies

2016 ◽  
Vol 7 (2) ◽  
pp. 214-227 ◽  
Author(s):  
S. Suganya ◽  
A. Saravanan ◽  
P. Senthil Kumar ◽  
M. Yashwanthraj ◽  
P. Sundar Rajan ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Metal Ion ◽  
Adsorption Process ◽  
Second Order ◽  
Ion Concentration ◽  
Batch Adsorption ◽  
Equilibrium Studies ◽  
Adsorption Mode ◽  
Monolayer Adsorption ◽  
Pseudo Second Order

In the present study, the microalga Rhizoclonium hookeri (RH) was effectively applied to remove the metal ions [Pb(II) and Ni(II)] from aqueous solution in batch adsorption mode experiments. The adsorption process was influenced by several operating parameters such as initial metal ion concentration, contact time, pH, particle size, adsorbent dose, and temperature. The maximum monolayer adsorption capacity of the RH was found to be 81.7 mg g−1 and 65.81 mg g−1 for Pb(II) and Ni(II) ions, respectively, at optimum conditions. The calculated thermodynamic parameters illustrated that the adsorption process was found to be spontaneous and endothermic in nature. Experimental data were analyzed in terms of pseudo-first order, pseudo-second order, and Elovich kinetic models. The results showed that the removal of Pb(II) and Ni(II) ions followed the pseudo-second order kinetics. The adsorption isotherm data were described using two and three parameter models. The results indicate that the adsorption data were best fitted with the Sips isotherm model. Consequently, the microalga RH with good adsorbability and reusability could be used as an effective adsorbent for the adsorption of Pb(II) and Ni(II) ions from wastewater.

scholarly journals Enhancing acidic dye adsorption by modified UiO-66

2020 ◽  
Vol 1 (2) ◽  
pp. 54-62
Author(s):  
Naser Al Amery ◽  
Hussein Rasool Abid ◽  
Shaobin Wang ◽  
Shaomin Liu
Keyword(s):  
Adsorption Process ◽  
Dye Adsorption ◽  
Batch Adsorption ◽  
First Order ◽  
Freundlich Isotherms ◽  
Adsorption Capacities ◽  
Pseudo Second Order ◽  
The Stability ◽  
Second Order Equations ◽  
Better Than

In this study, two improved versions of UiO-66 were successfully synthesised. Modified UiO-66 and UiO-66-Ce were characterised to confirm the integrity of the structure, the stability of functional groups on the surface and the thermal stability. Activated samples were used for removal harmful anionic dye (methyl orange) (MO) from wastewater. Batch adsorption process was relied to investigate the competition between those MOFs for removing MO from aqueous solution. Based on the results, at a higher initial concentration, the maximum MO uptake was achieved by UiO-66-Ce which was better than modified-UiO-66. They adsorbed 71.5 and 62.5 mg g-1 respectively. Langmuir and Freundlich isotherms were employed to simulate the experimental data. In addition, Pseudo first order and Pseudo second order equations were used to describe the dynamic behaviour of MO through the adsorption process. The high adsorption capacities on these adsorbents can make them promised adsorbents in industrial areas.

scholarly journals Recovery of phosphate from aqueous solution by magnetically recycled modified polishing powder composites

2019 ◽  
Vol 80 (7) ◽  
pp. 1357-1366
Author(s):  
Jianming Liu ◽  
Runying Bai ◽  
Junfeng Hao ◽  
Bowen Song ◽  
Yu Zhang ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Ligand Exchange ◽  
Adsorption Process ◽  
High Adsorption ◽  
Order Model ◽  
Powder Composites ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ph Level ◽  
Adsorption Desorption

Abstract This study investigated a magnetically recycled modified polishing powder (CMIO@PP) as an adsorbent of phosphate; the CMIO@PP was synthesized by combining the modified La/Ce-containing waste polishing powder with CaO2-modified Fe3O4 (CMIO). Results indicate that the CMIO@PP nanocomposite presents a crystal structure comprising La (OH)3, Ce (OH)3, and Fe3O4, and that CMIO is uniformly dispersed in the modified polishing powder. The CMIO@PP (1:3) is a suitable choice considering its magnetism and adsorption capacity. The magnetic adsorbent exhibits a high adsorption capacity of 53.72 mg/g, a short equilibrium time of 60 min, and superior selectivity for phosphate. Moreover, the adsorbent strongly depends on the pH during the adsorption process and maintains a large adsorption capacity when the pH level is between 2 and 6. The adsorption of phosphate by the CMIO@PP (1:3) accords with the Langmuir isotherm model, and the adsorption process follows the pseudo-second order model. Meanwhile, adsorption–desorption experiments show that the adsorbent could be recycled a few times and that a high removal efficiency of phosphate from civil wastewater was achieved. Finally, mechanisms show that the adsorption of phosphate by the CMIO@PP (1:3) is mainly caused by electrostatic attraction and ligand exchange.

Adsorption of Copper Ions from Wastewater by Carboxymethylcellulose Sulfate

2011 ◽  
Vol 393-395 ◽  
pp. 1098-1101 ◽  
Author(s):  
Yan Yu ◽  
Feng Yuan Huang
Keyword(s):  
Contact Time ◽  
Copper Concentration ◽  
Adsorption Process ◽  
Ph Value ◽  
Copper Ions ◽  
Adsorption Capacities ◽  
Monolayer Adsorption ◽  
Optimum Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model

In the present paper, the ability of carboxymethylcellulose sulfate (CMC-S) for Cu(II) removal was studied. The influence of factors, such as the pH value, the initial copper concentrations, and the contact time, were investigated in detail. Atomic absorption spectrophotometer was applied to determined the concentration of Cu(II). The results showed that the adsorption process was strongly dependent on the pH value and the initial copper concentration. The optimum pH value was in the range of 6-7. The theoretical adsorption capacities for Cu(II) was 127.7 mg/g. The equilibrium data was well fitted to the Langmuir isotherm model at 25°C, which can be explained as a monolayer adsorption.

scholarly journals Removal of Cd(II) Ions from Simulated Wastewater by HCl Modified Cucumis sativus Peel: Equilibrium and Kinetic Study

2014 ◽  
Vol 7 ◽  
pp. ASWR.S16488 ◽  
Author(s):  
Ruchi Pandey ◽  
Nasreen Ghazi Ansari ◽  
Ram Lakhan Prasad ◽  
Ramesh Chandra Murthy
Keyword(s):  
Cucumis Sativus ◽  
Adsorption Process ◽  
Order Reaction ◽  
Ion Concentration ◽  
Second Order Reaction ◽  
Monolayer Adsorption ◽  
Optimum Ph ◽  
Pseudo Second Order ◽  
Simulated Wastewater ◽  
Maximum Removal

This paper describes the adsorption of Cd(II) ions from aqueous solutions by modified Cucumis sativus peel (CSP) by HCl treatment. The optimum pH, adsorbent mass, contact time, and initial ion concentration were determined. The maximum removal efficiency was 84.85% for 20 mg/L Cd(II) ion at pH 5. The adsorption isotherms were obtained using concentrations of the metal ions ranging from 5 to 150 mg/L. The adsorption process follows Langmuir isotherm and pseudo-second-order reaction kinetics. CSPs exhibit monolayer adsorption capacity of 58.14 mg/g at 298 K. The paper also discusses the thermodynamic parameters of the adsorption (the Gibbs free energy, entropy, and enthalpy). Our results establish that the adsorption process was spontaneous and endothermic under normal conditions.

Ferric ion adsorption and electrodesorption by carbon nanotubes and nanofibres films

2009 ◽  
Vol 59 (8) ◽  
pp. 1657-1663 ◽  
Author(s):  
Haibo Li ◽  
Likun Pan ◽  
Yanping Zhang ◽  
Zhuo Sun
Keyword(s):  
Carbon Nanotubes ◽  
Adsorption Process ◽  
Physical Adsorption ◽  
Chemical Vapor ◽  
Ion Adsorption ◽  
Order Model ◽  
First Order ◽  
Monolayer Adsorption ◽  
Pressure Chemical ◽  
Kinetics And Isotherms

Carbon nanotubes and nanofibres (CNTs-CNFs) films have been grown on Ni sheets by low pressure chemical vapor deposition system and show good physical adsorption capability for ferric (Fe3 + ) ions. The studies of adsorption kinetics and isotherms indicate that Fe3 +  adsorption process was regarded as first-order model and followed a Langmuir isotherm indicating monolayer adsorption. The saturated CNTs-CNFs film is easy to be regenerated by electrodesorption with direct voltage applied. The result shows that the combination of adsorption and electrodesorption by CNTs-CNFs is a promising technology to remove the Fe3 +  contamination in solution, which can be further extended to the process of other heavy metal ions.

scholarly journals High Removal Efficiency of Diatomite-Based X Zeolite for Cu2+ and Zn2+

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6525
Author(s):  
Guangyuan Yao ◽  
Yuqiang Liu ◽  
Shuilin Zheng ◽  
Ya Xu
Keyword(s):  
Ion Exchange ◽  
Adsorption Process ◽  
Interface Properties ◽  
Order Model ◽  
Adsorption Capacities ◽  
Adsorption Data ◽  
X Zeolite ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Kinetics And Isotherms

Diatomite-based X zeolite was obtained and its crystallinity, morphology, and interface properties were investigated by XRD, BET, SEM, EDS, and XRF. The obtained X zeolite possessed a unique meso-microporous structure and showed good ion exchange properties for Cu2+ and Zn2+. The pseudo-second-order model and Langmuir isotherm model can best describe the adsorption kinetics and isotherms of Cu2+ and Zn2+, respectively. The maximal adsorption capacities of X zeolite for Cu2+ and Zn2+ were 146 and 195 mg/g at 323 K, respectively. Meanwhile, the adsorption process for Cu2+ and Zn2+ were chemical adsorption and ion exchange, respectively. Furthermore, the adsorption data turned out to be an endothermic and spontaneous process. Compared with other reported materials, the adsorption capacity of X zeolite synthesized from diatomite was among the highest. Therefore, it could be a promising adsorbent for the disposal of wastewater that contains metal ions.

Sign in / Sign up

Export Citation Format

Share Document