scholarly journals Theoretical Study of Proton Radiation Influence on the Performance of a Polycrystalline Silicon Solar Cell

2019 ◽  
Vol 2019 ◽  
pp. 1-7
Author(s):  
Tchouadep Guy Serge ◽  
Zouma Bernard ◽  
Korgo Bruno ◽  
Soro Boubacar ◽  
Savadogo Mahamadi ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Silicon Solar Cell ◽  
Short Circuit ◽  
Experimental Studies ◽  
High Energy ◽  
High Energy Particle ◽  
Proton Radiation ◽  
Electrical Parameters ◽  
Carrier Distribution

The aim of this work is to study the behaviour of a silicon solar cell under the irradiation of different fluences of high-energy proton radiation (10 MeV) and under constant multispectral illumination. Many theoretical et experimental studies of the effect of irradiation (proton, gamma, electron, etc.) on solar cells have been carried out. These studies point out the effect of irradiation on the behaviour of the solar cell electrical parameters but do not explain the causes of these effects. In our study, we explain fundamentally the causes of the effects of the irradiation on the solar cells. Taking into account the empirical formula of diffusion length under the effect of high-energy particle irradiation, we established new expressions of continuity equation, photocurrent density, photovoltage, and dynamic junction velocity. Based on these equations, we studied the behaviour of some electronic and electrical parameters under proton radiation. Theoretical results showed that the defects created by the irradiation change the carrier distribution and the carrier dynamic in the bulk of the base and then influence the solar cell electrical parameters (short-circuit current, open-circuit voltage, conversion efficiency). It appears also in this study that, at low fluence, junction dynamic velocity decreases due to the presence of tunnel defects. Obtained results could lead to improve the quality of the junction of a silicon solar cell.

scholarly journals PREPARATION AND CHARACTERIZATION OF P3HT-PCBM ORGANIC SOLAR CELLS

2013 ◽  
pp. 23-25
Author(s):  
ANUBHAV GUPTA ◽  
PRAVEEN S ◽  
ABHISHEK KUMAR ◽  
PRIYANKA SHREE ◽  
SUCHANA MISHRA
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Silicon Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Glass Substrates

Organic solar cells using P3HT: PCBM as an active layer on ITO coated glass substrates were fabricated and characterized. Different air annealing procedures and cathode materials were tried and the characteristics were compared with that of a standard thin film polycrystalline silicon solar cell. It was found that the sample prepared with post-deposition air annealing at 130 oC improves the open circuit voltage (Voc) considerably. Besides, short circuit current (Isc) and the efficiency (η) were highest for the sample with a non annealed active layer. Series resistance (Rs) for this sample was lowest, but 103 times higher than that of the silicon solar cell, which in turn may have reduced the efficiency value for the organic cell compared to silicon.

scholarly journals Assessing the impact of front grid metallization pattern on the performance of silicon solar cells

2021 ◽  
Author(s):  
Saba Siraj ◽  
Sofia Akbar Tahir ◽  
Adnan Ali
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Contact Resistance ◽  
Silicon Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Research Work ◽  
Maximum Efficiency ◽  
Silicon Solar Cells ◽  
The Impact

Abstract The aim of this research work was to assess the impact of front and rear grid metallization pattern on the performance of silicon solar cells. We have investigated the effect of front grid metallization design and geometry on the open-circuit voltage (Voc), short circuit current density (Jsc), fill factor (FF) and efficiency (ŋ) of silicon solar cells by using Griddler 2.5 simulation program. We used different number of metal fingers ranging from 80–120 having width of 60 µm and different number of busbars ranging from 1–5 busbars on the front and rear side of solar cells for optimization. We have also calculated the efficiency and fill factor at different values of front contact resistance ranging from (0.1–100) mohm-cm2, front and rare layer sheet resistances ranging from (60–110) ohm/sq and different edge gaps. We found that the maximum efficiency and fill factor was obtained with those parameters, when front and rare contact resistances were taken as same. We have designed an optimized silicon solar cell with 115 number of fingers, 4 busbars, front and rare contact resistance of 0.1 mohm-cm2 and front and rare layer sheet resistance of 60 ohm/sq. In this way we were able to successfully optimize the silicon solar cell having efficiency and fill factor of 19.49 % and 81.36 % respectively, for our best optimized silicon solar cell.

Optical Microconcentrator System for Enhancing Solar Cell Photovoltaic Performances

2016 ◽  
Vol 369 ◽  
pp. 65-70 ◽  
Author(s):  
Elena Manea ◽  
Catalin Parvulescu ◽  
Munizer Purica ◽  
Elena Budianu ◽  
Constantin Tibeica
Keyword(s):  
Refractive Index ◽  
Solar Cells ◽  
Solar Cell ◽  
Intermediate Layer ◽  
Large Scale ◽  
Silicon Solar Cell ◽  
Short Circuit ◽  
Glass Plate ◽  
Front Surface ◽  
Corning Glass

In this paper, we present two optical microconcentrator systems consisting of an array of microlenses formed with an intermediate layer deposited between a textured glass plate and the front surface of a silicon solar cell and polydimethylsiloxane (PDMS) microlenses based on replication of molds etched on glass. The optical coupling microlenses are fabricated using simple photolithography techniques that make the design compatible with silicon technology and large-scale manufacturing.We experimented with a honeycomb texturization on Corning glass plate having an area of 2x2 cm2. A wet etching process that led to a transparent surface with micro-cavities of 20 μm diameter and a depth of 6 μm was used. The intermediate layer was chosen depending on the refractive index. Materials with the refractive index in the range of 1 - 1.43 were experimented. The structures of silicon solar cells covered with the intermediate layer and texturized glass were characterized by illuminating and measuring the short-circuit photocurrent. It was obtained an improvement of 6.7 % of the short-circuit photocurrent for the optical microconcentrator system solar cells as compared to a structure covered with an untextured glass plate without intermediate layer. The microconcentrator consisting of the PDMS microlenses gave better results, an increase of the photocurrent of over 9%.The simulations of this system were done by using an OptiFTDT software. The aim of the simulations was to establish the distribution of the radiation which crosses the optical microconcentrator system and hits the solar cells surface. The simulation results are in agreement with the obtained experimental data.

scholarly journals Efficient Light Management in a Monolithic Tandem Perovskite/Silicon Solar Cell by Using a Hybrid Metasurface

Nanomaterials ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 791 ◽  
Author(s):  
Mahmoud H. Elshorbagy ◽  
Braulio García-Cámara ◽  
Eduardo López-Fraguas ◽  
Ricardo Vergaz
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Silicon Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Back Contact ◽  
Light Management ◽  
Promising Solution ◽  
Conversion Efficiencies

Solar energy is now dealing with the challenge of overcoming the Shockley–Queisser limit of single bandgap solar cells. Multilayer solar cells are a promising solution as the so-called third generation of solar cells. The combination of materials with different bandgap energies in multijunction cells enables power conversion efficiencies up to 30% at reasonable costs. However, interfaces between different layers are critical due to optical losses. In this work, we propose a hybrid metasurface in a monolithic perovskite-silicon solar cell. The design takes advantage of light management to optimize the absorption in the perovskite, as well as an efficient light guiding towards the silicon subcell. Furthermore, we have also included the effect of a textured back contact. The optimum proposal provides an enhancement of the matched short-circuit current density of a 20.5% respect to the used planar reference.

scholarly journals Numerical Investigation of Graphene as a Back Surface Field Layer on the Performance of Cadmium Telluride Solar Cell

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3275
Author(s):  
Devendra KC ◽  
Deb Kumar Shah ◽  
M. Shaheer Akhtar ◽  
Mira Park ◽  
Chong Yeal Kim ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Doping Concentration ◽  
Carrier Lifetime ◽  
Short Circuit ◽  
Back Surface ◽  
Back Surface Field ◽  
Cdte Solar Cell ◽  
Cdte Solar Cells ◽  
Surface Field

This paper numerically explores the possibility of ultrathin layering and high efficiency of graphene as a back surface field (BSF) based on a CdTe solar cell by Personal computer one-dimensional (PC1D) simulation. CdTe solar cells have been characterized and studied by varying the carrier lifetime, doping concentration, thickness, and bandgap of the graphene layer. With simulation results, the highest short-circuit current (Isc = 2.09 A), power conversion efficiency (h = 15%), and quantum efficiency (QE ~ 85%) were achieved at a carrier lifetime of 1 × 103 ms and a doping concentration of 1 × 1017 cm−3 of graphene as a BSF layer-based CdTe solar cell. The thickness of the graphene BSF layer (1 mm) was proven the ultrathin, optimal, and obtainable for the fabrication of high-performance CdTe solar cells, confirming the suitability of graphene material as a BSF. This simulation confirmed that a CdTe solar cell with the proposed graphene as the BSF layer might be highly efficient with optimized parameters for fabrication.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals Cell/Module Integration Technology with Wire-Embedded EVA Sheet

2021 ◽  
Vol 11 (9) ◽  
pp. 4170
Author(s):  
Jeong Eun Park ◽  
Won Seok Choi ◽  
Donggun Lim
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
High Power ◽  
Short Circuit ◽  
Optical Loss ◽  
Manufacturing Cost ◽  
Power Module ◽  
Manufacturing Method ◽  
Front Electrode ◽  
The Wire

Silicon wafers are crucial for determining the price of solar cell modules. To reduce the manufacturing cost of photovoltaic devices, the thicknesses of wafers are reduced. However, the conventional module manufacturing method using the tabbing process has a disadvantage in that the cell is damaged because of the high temperature and pressure of the soldering process, which is complicated, thus increasing the process cost. Consequently, when the wafer is thinned, the breakage rate increases during the module process, resulting in a lower yield; further, the module performance decreases owing to cracks and thermal stress. To solve this problem, a module manufacturing method is proposed in which cells and wires are bonded through the lamination process. This method minimizes the thermal damage and mechanical stress applied to solar cells during the tabbing process, thereby manufacturing high-power modules. When adopting this method, the front electrode should be customized because it requires busbarless solar cells different from the existing busbar solar cells. Accordingly, the front electrode was designed using various simulation programs such as Griddler 2.5 and MathCAD, and the effect of the diameter and number of wires in contact with the front finger line of the solar cell on the module characteristics was analyzed. Consequently, the efficiency of the module manufactured with 12 wires and a wire diameter of 0.36 mm exhibited the highest efficiency at 20.28%. This is because even if the optical loss increases with the diameter of the wire, the series resistance considerably decreases rather than the loss of the short-circuit current, thereby improving the fill factor. The characteristics of the wire-embedded ethylene vinyl acetate (EVA) sheet module were confirmed to be better than those of the five busbar tabbing modules manufactured by the tabbing process; further, a high-power module that sufficiently compensated for the disadvantages of the tabbing module was manufactured.

scholarly journals GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 726
Author(s):  
Ray-Hua Horng ◽  
Yu-Cheng Kao ◽  
Apoorva Sood ◽  
Po-Liang Liu ◽  
Wei-Cheng Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Low Temperature ◽  
Triple Junction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Metal Line ◽  
Solar Simulator ◽  
Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

17.8%-efficient Amorphous Silicon Heterojunction Solar Cells on p-type Silicon Wafers

2006 ◽  
Vol 910 ◽  
Author(s):  
Qi Wang ◽  
Matt P. Page ◽  
Eugene Iwancizko ◽  
Yueqin Xu ◽  
Yanfa Yan ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Amorphous Silicon ◽  
High Efficiency ◽  
Short Circuit ◽  
Open Circuit ◽  
Layer Growth ◽  
Surface Recombination Velocity ◽  
Back Contact ◽  
P Type

AbstractWe have achieved an independently-confirmed 17.8% conversion efficiency in a 1-cm2, p-type, float-zone silicon (FZ-Si) based heterojunction solar cell. Both the front emitter and back contact are hydrogenated amorphous silicon (a-Si:H) deposited by hot-wire chemical vapor deposition (HWCVD). This is the highest reported efficiency for a HWCVD silicon heterojunction (SHJ) solar cell. Two main improvements lead to our most recent increases in efficiency: 1) the use of textured Si wafers, and 2) the application of a-Si:H heterojunctions on both sides of the cell. Despite the use of textured c-Si to increase the short-circuit current, we were able to maintain the same 0.65 V open-circuit voltage as on flat c-Si. This is achieved by coating a-Si:H conformally on the c-Si surfaces, including covering the tips of the anisotropically-etched pyramids. A brief atomic H treatment before emitter deposition is not necessary on the textured wafers, though it was helpful in the flat wafers. It is essential to high efficiency SHJ solar cells that the emitter grows abruptly as amorphous silicon, instead of as microcrystalline or epitaxial Si. The contact on each side of the cell comprises a thin (< 5 nm) low substrate temperature (~100°C) intrinsic a-Si:H layer, followed by a doped layer. Our intrinsic layers are deposited at 0.3-1.2 nm/s. The doped emitter and back-contact layers were deposited at a higher temperature (>200°C) and grown from PH3/SiH4/H2 and B2H6/SiH4/H2 doping gas mixtures, respectively. This combination of low (intrinsic) and high (doped layer) growth temperatures was optimized by lifetime and surface recombination velocity measurements. Our rapid efficiency advance suggests that HWCVD may have advantages over plasma-enhanced (PE) CVD in fabrication of high-efficiency heterojunction c-Si cells; there is no need for process optimization to avoid plasma damage to the delicate, high-quality, Si wafers.

Sign in / Sign up

Export Citation Format

Share Document