scholarly journals Effect of Aluminum Incorporation into Mesoporous Aluminosilicate Framework on Drug Release Kinetics

2017 ◽  
Vol 2017 ◽  
pp. 1-9
Author(s):  
Raul-Augustin Mitran ◽  
Daniela Berger ◽  
Jeanina Pandele-Cusu ◽  
Cristian Matei
Keyword(s):  
Pore Size ◽  
Therapeutic Agent ◽  
Release Kinetics ◽  
Nitrogen Adsorption ◽  
Incipient Wetness Impregnation ◽  
X Ray Diffraction ◽  
Drug Molecules ◽  
Model Drug ◽  
Adsorption Desorption

Mesoporous silica materials are promising nanocarriers for the development of drug delivery systems. In this study, the influence of pore size, volume, surface area, and doping the silica framework on the release kinetics of a model drug, metoprolol, has been studied. 20% or 50% wt. therapeutic agent was loaded into the carrier mesopores through incipient wetness impregnation. The carriers and drug-loaded samples have been characterized by small- and wide-angle X-ray diffraction, FT-IR spectroscopy, scanning electron microscopy, and nitrogen adsorption-desorption isotherms. The in vitro release profiles have been fitted using a three-parameter kinetic model and they have been explained in terms of the release rate during the burst and sustained release stages and the fraction of drug molecules released during the burst stage. The silica framework doping with aluminum was found to decrease the amount of drug released in the burst stage, without affecting the other kinetic parameters. The therapeutic agent release rates depend mainly on the pore size and volume of the mesoporous carriers and drug-loaded samples.

Positron Annihilation Study of Porous ZnO Synthesized with Soft Template

2017 ◽  
Vol 373 ◽  
pp. 299-302
Author(s):  
Bo Zhou ◽  
Chong Yang Li ◽  
Ning Qi ◽  
Zhi Quan Chen
Keyword(s):  
Pore Size ◽  
Positron Lifetime ◽  
Nitrogen Adsorption ◽  
Soft Template ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Long Lifetime ◽  
Positron Annihilation Study ◽  
Adsorption Desorption

Porous ZnO were synthesized with soft template method using zinc acetate Zn (CH3COO)2·2H2O as precursor and block copolymer F127 as the surfactant. Nitrogen adsorption-desorption measurements indicate that the ZnO sample contains large pores with mean diameter of about 30 nm. However, both small-angle X-ray diffraction and transmission electron microscope measurements indicate that the pore ordering is missing. Positron lifetime measurements reveal two long lifetime components in the porous ZnO. The longest lifetime τ4 (75 ns) corresponds to ortho-positronium (o-Ps) annihilation in large pores. The pore size estimated from τ4 is about 10.6 nm. This is much smaller than that estimated from Nitrogen adsorption-desorption measurements. In addition, the intensity I4 is only about 2.2%. This is probably due to the chemical quenching and/or inhibition of positronium formation induced by ZnO, which reduces o-Ps lifetime and intensity, and leads to under estimation of the pore size.

Porous LiMn2O4 Microspheres With Different Pore Size: Preparation and Application as Cathode Materials for Lithium Ion Batteries

2018 ◽  
Vol 16 (1) ◽  
Author(s):  
Shiyou Li ◽  
Konglei Zhu ◽  
Jinliang Liu ◽  
Dongni Zhao ◽  
Xiaoling Cui
Keyword(s):  
Pore Size ◽  
Lithium Ion Batteries ◽  
Rate Capability ◽  
Lithium Ion ◽  
Nitrogen Adsorption ◽  
Electrochemical Performances ◽  
Discharge Process ◽  
Ion Diffusion ◽  
X Ray Diffraction ◽  
Adsorption Desorption

Three types of LiMn2O4 (LMO) microspheres with different pore size are prepared by a facile method, using porous MnCO3–MnO2 and Mn2O3 microspheres as the self-supporting template, for lithium ion batteries (LIBs) cathode material. Briefly, Mn2O3 and MnO2 microspheres are heated in air at 600 °C for 10 h to synthesize porous Mn2O3 spheres. Then the mixture of as-prepared spherical Mn2O3 and LiNO3 is calcined to obtain the LMOs. The morphology and structure of LMOs are characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and nitrogen adsorption/desorption analyses. The result shows that the maximum pore diameters of LMOs are 17 nm, 19 nm, and 11 nm, respectively. All LMOs microspheres are composed of similar sized nanoparticles; however, the surface of these microspheres is strewed with dense tinier pores or sparse larger pores. Generally, the nanoparticles will reduce the path of Li+ ion diffusion and increases the reaction sites for lithium insertion/extraction. Moreover, the pores can provide buffer spaces for the volume changes during charge–discharge process. The electrochemical performances of LMOs are investigated and LMO2 exhibits extremely good electrochemical behavior, especially the rate capability. The as-prepared LMO2 delivers a discharge capacity of 124.3 mAh g−1 at 0.5 C, retaining 79.6 mAh g−1 even at 5 C. The LMO2 sample also shows good capacity retention of 96.9% after 100 cycles at 0.5 C.

scholarly journals Carbonization of Lignin Extracted from Liquid Waste of Coconut Coir Delignification

2020 ◽  
Vol 20 (4) ◽  
pp. 842
Author(s):  
Widiyastuti Widiyastuti ◽  
Mahardika Fahrudin Rois ◽  
Heru Setyawan ◽  
Siti Machmudah ◽  
Diky Anggoro
Keyword(s):  
Pore Size ◽  
Surface Area ◽  
Liquid Waste ◽  
Nitrogen Adsorption ◽  
Nitrogen Atmosphere ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Coconut Coir ◽  
Xrd Patterns ◽  
Adsorption Desorption

Lignin as a by-product of the pulping process is less widely used for worth materials. In this study, the utilization of lignin by-product of the soda delignification process of coconut coir converted to the activated carbon by a simple precipitation method followed by the carbonization at various temperatures is presented. The by-product liquor of the soda delignification process having a pH of 13.4 was neutralized by dropping of hydrochloric acid solution to achieve the pH solution of 4 resulting in the lignin precipitation. The precipitated was washed, filtered, and dried. The dried lignin was then carbonized under a nitrogen atmosphere at various temperatures of 500, 700, and 900 °C. The dried lignin and carbonized samples were characterized using SEM, XRD, FTIR, and nitrogen adsorption-desorption analyzer, to examine their morphology, X-Ray diffraction pattern, chemical bonding interaction, and surface area-pore size distribution, respectively. The characterization results showed that the functional groups of lignin mostly disappeared gradually with the increase of temperature approached the graphite spectrum. The XRD patterns confirmed that the carbonized lignin particles were amorphous and assigned as graphitic. All samples had a pore size of 3–4 nm classified as mesoporous particles. This study has shown that the carbonization lignin at a temperature of 700 °C had the highest surface area (i.e. 642.5 m2/g) in which corresponds to the highest specific capacitance (i.e. 28.84 F/g).

Antheraea pernyi Silk Fibroin Microspheres Carried Lysozyme

2014 ◽  
Vol 915-916 ◽  
pp. 875-878 ◽  
Author(s):  
Juan Wang ◽  
Gui Jun Li ◽  
Rui Jiang ◽  
Zhu Ping Yin ◽  
Shen Zhou Lu
Keyword(s):  
Silk Fibroin ◽  
Release Kinetics ◽  
In Vitro Release ◽  
X Ray Diffraction ◽  
Antheraea Pernyi ◽  
Encapsulation Rate ◽  
Release Field ◽  
Model Drug ◽  
Vitro Release

A method was developed to prepare the Antheraea Pernyi silk fibroin (ASF) microspheres using lysozyme as a model drug to estimate the application of ASF in drug controlled release field. The structure of ASF microsphere carried drug was characterized by X-ray diffraction and FTIR. The morphology and the influence of the microspheres on the degradation of lysozyme were investigated using scanning electron microscope. The results show that encapsulation rate was increased and drug content was decreased with the addition of lysozyme increasing. In vitro release of lysozyme from the ASF particles we demonstrated that the release kinetics depends on the pH. The pH played important roles in controlling lysozyme release profiles. It also can be seen that the degradation speed of lysozyme ASF microspheres slightly larger than the pure ASF microspheres.

Application of raw and modified Uruguayan clays to phosphate adsorption for water remediation

MRS Advances ◽  
2018 ◽  
Vol 3 (61) ◽  
pp. 3543-3549
Author(s):  
Pablo González ◽  
Andrea C. De Los Santos ◽  
Jorge R. Castiglioni ◽  
María A. De León
Keyword(s):  
Nitrogen Adsorption ◽  
Pillared Clay ◽  
Water Remediation ◽  
Phosphate Adsorption ◽  
X Ray Diffraction ◽  
Order Model ◽  
Freundlich Model ◽  
X Ray ◽  
First Order ◽  
Adsorption Desorption

ABSTRACTA raw clay from Uruguay was modified with aluminium to obtain an aluminium pillared clay (Al-PILC). The solids were characterized by scanning electron microscopy, X-ray diffraction and nitrogen adsorption-desorption isotherms. The Al-PILC retained the typical laminar structure of montmorillonite. The specific surface area and the microporous volume of the Al-PILC, 235 m2 g-1 and 0.096 cm3 g-1, respectively, were much higher than those of the clay. The phosphate adsorption capacity of the Al-PILC was higher than those of the clay. The phosphate adsorption kinetic followed the pseudo-first-order model for both, the clay and the Al-PILC, and the phosphate adsorption isotherm for the Al-PILC fit the Freundlich model.

scholarly journals Development of a reservoir type prolonged release system with felodipine via simplex methodology

2015 ◽  
Vol 89 (1) ◽  
pp. 128-136
Author(s):  
Rareș Iuliu Iovanov ◽  
Ioan Tomuță ◽  
Sorin Emilian Leucuța
Keyword(s):  
Simplex Method ◽  
Release Kinetics ◽  
Prolonged Release ◽  
Lauryl Sulfate ◽  
Pore Former ◽  
Release System ◽  
Reservoir Type ◽  
Model Drug ◽  
Kinetics Of

Background and aims. Felodipine is a dihydropyridine calcium antagonist that presents good characteristics to be formulated as prolonged release preparations. The aim of the study was the formulation and in vitro characterization of a reservoir type prolonged release system with felodipine, over a 12 hours period using the Simplex method.Methods. The first step of the Simplex method was to study the influence of the granules coating method on the felodipine release. Furthermore the influence of the coating polymer type, the percent of the coating polymer and the percent of pore forming agent in the coating on the felodipine release were studied. Afterwards these two steps of the experimental design the percent of Surelease applied on the felodipine loaded granules and the percent of pore former in the polymeric coating formulation variables were studied. The in vitro dissolution of model drug was performed in phosphate buffer solution (pH 6.5) with 1% sodium lauryl sulfate. The released drug quantification was done using an HPLC method. The release kinetics of felodipine from the final granules was assessed using different mathematical models.Results. A 12 hours release was achieved using granules with the size between 315 – 500 µm coated with 45% Surelease with different pore former ratios in the coating via the top-spray method.Conclusion. We have prepared prolonged release coated granules with felodipine using a fluid bed system based on the Simplex method. The API from the studied final formulations was released over a 12 hours period and the release kinetics of the model drug substance from the optimized preparations fitted best the Higuchi and Peppas kinetic models. 

scholarly journals Highly Porous Carbon Materials Filled with Nickel Hydroxide Nanoparticles; Synthesis, Study, Application in Electrochemistry

2015 ◽  
Vol 17 (3) ◽  
pp. 187 ◽  
Author(s):  
Yu.A. Zakharov ◽  
A.N. Voropay ◽  
N.M. Fedorova ◽  
V.M. Pugachev ◽  
A.V. Puzynin ◽  
...  
Keyword(s):  
Porous Carbon ◽  
Nickel Hydroxide ◽  
Nitrogen Adsorption ◽  
Porous Carbon Material ◽  
X Ray Diffraction ◽  
Scanning Rate ◽  
Electrode Cell ◽  
Adsorption Desorption ◽  
Electrode Characteristics ◽  
Study Application

<p>Nickel hydroxide was deposited on the surface of the porous carbon to obtain a cathode material for supercapacitors. This work is the first part of the study of Ni(OH)<sub>2</sub>/С composite, which considers the conditions of its synthesis using two types of porous carbon matrices with a highly developed specific surface area (1000–3000 m<sup>2</sup>/g) and two types of precursors (NiCl<sub>2</sub>*6H<sub>2</sub>O and Ni(N<sub>3</sub>)<sub>2</sub>). The morphology of the systems, in particular the shape and size characteristics of the hydroxide filler particles, was examined using the scanning electron microscopy, X-ray diffraction, and nitrogen adsorption-desorption at 77 K. The measurements of capacity of the Ni(OH)<sub>2</sub>/С-electrodes were made in 6 M KOH using an asymmetric two-electrode cell (a porous carbon material with known electrode characteristics was employed as the counter electrode). The capacity was shown to decrease by 22–56% with increasing the scanning rate from 10 to 80 mV/s. A maximum capacity of the composite was obtained at a scanning rate of 10 mV/s was 346 F/g.</p>

Synthesis, characterization and formulation of sodium calcium silicate bioceramic for drug delivery applications

2016 ◽  
Vol 23 (4) ◽  
pp. 375-380
Author(s):  
P. Manohar Reddy ◽  
Ravy Lakshmi ◽  
Febin Prabhu Dass ◽  
Swamiappan Sasikumar
Keyword(s):  
Drug Delivery ◽  
Calcium Silicate ◽  
Release Kinetics ◽  
Release Profile ◽  
Apatite Formation ◽  
X Ray Diffraction ◽  
Drug Release Profile ◽  
Sodium Calcium ◽  
Calcium Magnesium ◽  
Model Drug

AbstractSodium calcium silicate (Na2CaSiO4) is a bioactive silicate with Na2O, CaO and SiO2 as its basic components, which is similar to that of the composition of bioactive glasses. In the present study, pure sodium calcium silicate was synthesized by rapid combustion technique, and the synthesized sample was characterized by powder X-ray diffraction to check the phase purity. The scaffolds were prepared by varying the ratio of sodium calcium silicate and polyvinyl alcohol, and the apatite-formation ability of the scaffolds was examined by soaking them in a simulated body fluid. The results revealed the formation of hydroxyapatite on the surface of the scaffold after 5 days, which is found to be rapid when compared with the bioactivity of the calcium silicates and calcium magnesium silicates. The scaffolds were also loaded with ciprofloxacin as a model drug and analyzed for its drug release profile using UV spectrophotometer. The release profile did not vary with the change in bioceramic-to-biopolymer ratio, and 60% of the drug was released in 10 days, which is within the appreciable range for a targeted drug delivery system. Moreover, the experimental and simulated values of the release kinetics were compared by applying the existing mathematical model.

Structural and surface aspects of thermally treated copper aluminium mixed hydroxides

1991 ◽  
Vol 69 (10) ◽  
pp. 1511-1515 ◽  
Author(s):  
Awad I. Ahmed ◽  
S. E. Samra ◽  
S. A. El-Hakam
Keyword(s):  
Pore Structure ◽  
Copper Content ◽  
Textural Properties ◽  
Nitrogen Adsorption ◽  
Phase Changes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Surface Areas ◽  
Structure Surface ◽  
Adsorption Desorption

CuO–Al2O3 catalysts containing various amounts of copper oxide have been prepared by precipitation. The phase changes were studied by X-ray diffraction. The results obtained revealed that the thermal treatment of solid CuO–Al2O3 at 700 °C produced only crystalline CuO. Heating to 900 °C led to the formation of copper alumina spinel together with unreacted CuO and γ-Al2O3. The spinel content was found to increase with increasing copper content. Nitrogen adsorption–desorption isotherms on the calcined samples have been measured. Surface areas have been calculated and the pore structure analysed. The textural properties of the system were found to depend on both the copper content and the calcination temperature. Key words: CuO, Al2O3 catalysts, structure, surface area, pore structure.

Immobilization of hemoglobin on stable mesoporous multilamellar silica vesicles and their activity and stability

2005 ◽  
Vol 20 (10) ◽  
pp. 2682-2690 ◽  
Author(s):  
Yufang Zhu ◽  
Weihua Shen ◽  
Xiaoping Dong ◽  
Jianlin Shi
Keyword(s):  
Thermal Stability ◽  
Pore Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Practical Applications ◽  
Silica Material ◽  
Transmission Electron ◽  
Mesoporous Support ◽  
Adsorption Desorption ◽  
Thermal Stability Of

A stable mesoporous multilamellar silica vesicle (MSV) was developed with a gallery pore size of about 14.0 nm. A simulative enzyme, hemoglobin (Hb), was immobilized on this newly developed MSV and a conventional mesoporous silica material SBA-15. The structures and the immobilization of Hb on the mesoporous supports were characterized with x-ray diffraction, transmission electron microscopy, N2 adsorption-desorption isotherms, Fourier transform infrared, ultraviolet-visible spectroscopy, and so forth. MSV is a promising support for immobilizing Hb due to its large pore size and high Hb immobilization capacity (up to 522 mg/g) compared to SBA-15 (236 mg/g). Less than 5% Hb was leached from Hb/MSV at pH 6.0. The activity study indicated that the immobilized Hb retained most peroxidase activity compared to free Hb. Thermal stability of the immobilized Hb was improved by the proctetive environment of MSV and SBA-15. Such an Hb-mesoporous support with high Hb immobilization capacity, high activity, and enhanced thermal stability will be attractive for practical applications.

Sign in / Sign up

Export Citation Format

Share Document