scholarly journals Physical Properties of ZnO Thin Films Codoped with Titanium and Hydrogen Prepared by RF Magnetron Sputtering with Different Substrate Temperatures

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Fang-Hsing Wang ◽  
Jen-Chi Chao ◽  
Han-Wen Liu ◽  
Tsung-Kuei Kang
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Film Surface ◽  
Hexagonal Wurtzite Structure ◽  
Rf Magnetron Sputtering ◽  
Force Microscopy ◽  
Glass Substrates ◽  
Transparent Conducting ◽  
Diffraction Patterns ◽  
Substrate Temperatures

Transparent conducting titanium-doped zinc oxide (TZO) thin films were prepared on glass substrates by RF magnetron sputtering using 1.5 wt% TiO2-doped ZnO as the target. Electrical, structural, and optical properties of films were investigated as a function of H2/(Ar + H2) flow ratios (RH) and substrate temperatures (TS). The optimalRHvalue for achieving high conducting TZO:H thin film decreased from 10% to 1% whenTSincreased from RT to 300°C. The lowest resistivity of9.2×10-4 Ω-cm was obtained asTS=100°C andRH=7.5%. X-ray diffraction patterns showed that all of TZO:H films had a hexagonal wurtzite structure with a preferred orientation in the (002) direction. Atomic force microscopy analysis revealed that the film surface roughness increased with increasingRH. The average visible transmittance decreased with increasingRHfor the RT-deposited film, while it had not considerably changed with differentRHfor the 300°C-deposited films. The optical bandgap increased asRHincreased, which is consistent with the Burstein-Moss effect. The figure of merits indicated thatTS=100°C andRH=7.5% were optimal conditions for TZO thin films as transparent conducting electrode applications.

Synthesis and Characterization of Nb-Doped TiO2 Thin Films Prepared by RF Magnetron Sputtering

2015 ◽  
Vol 1117 ◽  
pp. 139-142 ◽  
Author(s):  
Marius Dobromir ◽  
Radu Paul Apetrei ◽  
A.V. Rogachev ◽  
Dmitry L. Kovalenko ◽  
Dumitru Luca
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Rf Magnetron Sputtering ◽  
X Ray ◽  
Force Microscopy ◽  
Glass Substrates ◽  
Atomic Force ◽  
Vis Spectroscopy ◽  
Diffraction Patterns

Amorphous Nb-doped TiO2 thin films were deposited on (100) Si and glass substrates at room temperature by RF magnetron sputtering and a mosaic-type Nb2O5-TiO2 sputtering target. To adjust the amount of the niobium dopant in the film samples, appropriate numbers of Nb2O5 pellets were placed on the circular area of the magnetron target with intensive sputtering. By adjusting the discharge conditions and the number of niobium oxide pellets, films with dopant content varying between 0 and 16.2 at.% were prepared, as demonstrated by X-ray photoelectron spectroscopy data. The X-ray diffraction patterns of the as-deposited samples showed the lack of crystalline ordering in the samples. Surfaces roughness and energy band gap values increase with dopant concentration, as showed by atomic force microscopy and UV-Vis spectroscopy measurements.

EFFECT OF THICKNESS ON THE PROPERTIES OF In-DOPED ZnO THIN FILMS PREPARED BY RF MAGNETRON SPUTTERING

2011 ◽  
Vol 25 (07) ◽  
pp. 995-1003 ◽  
Author(s):  
L. P. PENG ◽  
L. FANG ◽  
X. F. YANG ◽  
Q. L. HUANG ◽  
F. WU ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Film Thickness ◽  
Visible Region ◽  
Hexagonal Wurtzite Structure ◽  
Rf Magnetron Sputtering ◽  
Transparent Electrode ◽  
Visible Range ◽  
Electrical And Optical Properties ◽  
Glass Substrates

In-doped zinc oxide ( ZnO:In ) thin films with thickness from 157 nm to 592 nm have been deposited on glass substrates by radio frequency (RF) magnetron sputtering. The effect of the film thickness on the structural, electrical and optical properties of ZnO:In thin films has been investigated. It is found that the films are hexagonal wurtzite structure with c-axis perpendicular to the substrate, and with increasing thickness, the crystallinity, the grains size and the conductivity of the films increases, but the strains along c-axis and the transmittance decrease. The decrease of the resistivity in a thicker film is attributed to the slight increase of the carrier concentration and the significant increase of Hall mobility. The transmittance of all the films is over 80% in the visible region (400–800 nm) and the band gap decrease with the increase of film thickness. The film with the thickness of around 303 nm has the resistivity of 6.07 × 10-3 Ω⋅ cm and the transmittance of 90% in the visible range. Based on the good conductivity and high transmittance, the ZnO:In films prepared by magnetron sputtering can be regarded as a potential transparent electrode.

scholarly journals DEPOSITION OF HIGH-ELECTRON-MOBILITY TRANSPARENT CONDUCTING ALUMINUM-DOPED ZINC OXIDE THIN FILMS BY DC MAGNETRON SPUTTERING

2018 ◽  
Vol 54 (1A) ◽  
pp. 160
Author(s):  
Hoang Van Dung
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Electron Mobility ◽  
High Electron ◽  
Dc Magnetron Sputtering ◽  
Glass Substrates ◽  
Transparent Conducting ◽  
Average Transmittance ◽  
Aluminum Doped Zinc Oxide ◽  
Substrate Temperatures

Transparent conducting Al-doped ZnO (AZO) thin films were deposited on glass substrates by DC magnetron sputtering from AZO ceramic target (0.75 %wt Al2O3) in gas mixture of (Ar + H2) at different substrate temperatures. At value of 1.7 % of ratio of H2 to (H2+Ar) and at substrate temperature of 200 oC, electron mobility in obtained AZO films is 60.2 cm2.V-1.s-1, which is much larger than 34.6 cm2.V-1.s-1 of films fabricated in the same condition without H2. AZO films also have a low resistivity of 2.53×10-4 Ω.cm, low sheet resistance of 2.5 Ω/□ and high average transmittance above 80 % in the wavelength range of 400 – 1100 nm.

Effect of the Heat Treatment on the Microstructure and Morphology of Cigs Thin Films Prepared by RF Magnetron Sputtering at Room Temperature

2020 ◽  
Vol 1012 ◽  
pp. 119-124
Author(s):  
Paulo Victor Nogueira da Costa ◽  
Rodrigo Amaral de Medeiro ◽  
Carlos Luiz Ferreira ◽  
Leila Rosa Cruz
Keyword(s):  
Thin Films ◽  
Heat Treatment ◽  
Magnetron Sputtering ◽  
Room Temperature ◽  
Morphological Changes ◽  
Film Surface ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Substrates

This work investigates the microstructural and morphological changes on CIGS thin films submitted to a post-deposition heat treatment. The CIGS 1000 nm-thick films were deposited at room temperature by RF magnetron sputtering onto glass substrates covered with molybdenum films. After deposition, the samples were submitted to a heat treatment, with temperatures ranging from 450 to 575 oC. The treatment was also carried out under a selenium atmosphere (selenization), from 400 to 500 oC. Morphological analyzes showed that the as-deposited film was uniform and amorphous. When the treatment was carried out without selenization, the crystallization occurred at or above 450 oC, and the grains remained nanosized. However, high temperatures led to the formation of discontinuities on the film surface and the formation of extra phases, as confirmed by X-ray diffraction data. The crystallization of the films treated under selenium atmosphere took place at lower temperatures. However, above 450 °C the film surface was discontinuous, with a lot of holes, whose amount increased with the temperature, showing that the selenization process was very aggressive. X-ray diffraction analyses showed that the extra phases were eliminated during selenization and the films had a preferential orientation along [112] direction. The results indicate that in the manufacturing process of solar cells, CIGS films deposited at room temperature should be submitted to a heat treatment carried out at 450 °C (without selenization) or 400 °C (with selenization).

Effect of RF Power on the Structural Properties of Magnetron Sputtered ZnO Thin Films Deposited at Room Temperature

2012 ◽  
Vol 626 ◽  
pp. 163-167
Author(s):  
Samsiah Ahmad ◽  
Nor Diyana Md Sin ◽  
M.N. Berhan ◽  
Mohamad Rusop
Keyword(s):  
Thin Films ◽  
Structural Properties ◽  
Room Temperature ◽  
Hexagonal Wurtzite Structure ◽  
Rf Magnetron Sputtering ◽  
Zno Thin Films ◽  
Rf Power ◽  
Force Microscopy ◽  
Glass Substrates ◽  
Sputtering Power

Zinc oxide thin films were prepared at room temperature in pure argon ambient on glass substrates by RF magnetron sputtering. The effect of sputtering power (50~250 Watt) on the structural properties of the film were investigated. The thickness of ZnO thin films was measured using surface profiler (Dektak 150+). Atomic force microscopy machine (AFM-Park system XE-100) was used to characterize the morphology while the crystalinity have been characterized using XRD (Rigaku Ultima IV). It was found that the thickness, growth rate and RMS roughness increases with increasing RF power. All films exhibit the (002) plane which correspond to hexagonal wurtzite structure with the highest peak at 150 Watt.

scholarly journals Residual Oxygen Effects on the Properties of MoS2 Thin Films Deposited at Different Temperatures by Magnetron Sputtering

Crystals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1183
Author(s):  
Peiyu Wang ◽  
Xin Wang ◽  
Fengyin Tan ◽  
Ronghua Zhang
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Magnetron Sputtering ◽  
Deposition Rate ◽  
Deposition Temperature ◽  
Energy Dispersive Spectrometer ◽  
Rf Magnetron Sputtering ◽  
Glass Substrates ◽  
Different Temperatures ◽  
Oxygen Atoms

Molybdenum disulfide (MoS2) thin films were deposited at different temperatures (150 °C, 225 °C, 300 °C, 375 °C, and 450 °C) on quartz glass substrates and silicon substrates using the RF magnetron sputtering method. The influence of deposition temperature on the structural, optical, electrical properties and deposition rate of the obtained thin films was investigated by X-ray diffraction (XRD), Energy Dispersive Spectrometer (EDS), Raman, absorption and transmission spectroscopies, a resistivity-measuring instrument with the four-probe method, and a step profiler. It was found that the MoS2 thin films deposited at the temperatures of 150 °C, 225 °C, and 300 °C were of polycrystalline with a (101) preferred orientation. With increasing deposition temperatures from 150 °C to 300 °C, the crystallization quality of the MoS2 thin films was improved, the Raman vibrational modes were strengthened, the deposition rate decreased, and the optical transmission and bandgap increased. When the deposition temperature increased to above 375 °C, the molecular atoms were partially combined with oxygen atoms to form MoO3 thin film, which caused significant changes in the structural, optical, and electrical properties of the obtained thin films. Therefore, it was necessary to control the deposition temperature and reduce the contamination of oxygen atoms throughout the magnetron sputtering process.

The piezoresistive properties research of SiC thin films prepared by RF magnetron sputtering

2019 ◽  
Vol 33 (15) ◽  
pp. 1950152 ◽  
Author(s):  
Jing Wu ◽  
Xiaofeng Zhao ◽  
Chunpeng Ai ◽  
Zhipeng Yu ◽  
Dianzhong Wen
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Cantilever Beam ◽  
Photoelectron Spectroscopy ◽  
Film Surface ◽  
Rf Magnetron Sputtering ◽  
Micro Electro Mechanical System ◽  
Gauge Factor ◽  
X Ray ◽  
Sputtering Power

To research the piezoresistive properties of SiC thin films, a testing structure consisting of a cantilever beam, SiC thin films piezoresistors and a Cr/Pt electrode is proposed in this paper. The chips of testing structure were fabricated by micro-electro-mechanical system (MEMS) technology on a silicon wafer with [Formula: see text]100[Formula: see text] orientation, in which SiC thin films were deposited by using radio-frequency (13.56 MHz) magnetron sputtering method. The effect of sputtering power, annealing temperature and time on the microstructure and morphology of the SiC thin films were investigated by the X-ray diffraction (XRD) and scanning electron microscopy (SEM). It indicates that a good continuity and uniform particles on the SiC thin film surface can be achieved at sputtering power of 160 W after annealing. To verify the existence of Si–C bonds in the thin films, X-ray photoelectron spectroscopy (XPS) was used. Meanwhile, the piezoresistive properties of SiC thin films piezoresistors were measured using the proposed cantilever beam. The test result shows that it is possible to achieve a gauge factor of 35.1.

scholarly journals Processing and Study of Optical and Electrical Properties of (Mg, Al) Co-Doped ZnO Thin Films Prepared by RF Magnetron Sputtering for Photovoltaic Application

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2146 ◽  
Author(s):  
Chayma Abed ◽  
Susana Fernández ◽  
Selma Aouida ◽  
Habib Elhouichet ◽  
Fernando Priego ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Magnetron Sputtering ◽  
Band Gap ◽  
Rf Magnetron Sputtering ◽  
Band Gap Energy ◽  
Thin Layers ◽  
Working Pressure ◽  
Hall Effect Measurements ◽  
Diffraction Patterns

In this study, high transparent thin films were prepared by radio frequency (RF) magnetron sputtering from a conventional solid state target based on ZnO:MgO:Al2O3 (10:2 wt %) material. The films were deposited on glass and silicon substrates at the different working pressures of 0.21, 0.61, 0.83 and 1 Pa, 300 °C and 250 W of power. X-ray diffraction patterns (XRD), atomic force microscopy (AFM), UV-vis absorption and Hall effect measurements were used to evaluate the structural, optical, morphological and electrical properties of thin films as a function of the working pressure. The optical properties of the films, such as the refractive index, the extinction coefficient and the band gap energy were systematically studied. The optical band gap of thin films was estimated from the calculated absorption coefficient. That parameter, ranged from 3.921 to 3.655 eV, was hardly influenced by the working pressure. On the other hand, the lowest resistivity of 8.8 × 10−2 Ω cm−1 was achieved by the sample deposited at the lowest working pressure of 0.21 Pa. This film exhibited the best optoelectronic properties. All these data revealed that the prepared thin layers would offer a good capability to be used in photovoltaic applications.

scholarly journals Growth and Characterization of (Tb,Yb) Co-Doping Sprayed ZnO Thin Films

Crystals ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 169 ◽  
Author(s):  
A. El hat ◽  
I. Chaki ◽  
R. Essajai ◽  
A. Mzerd ◽  
G. Schmerber ◽  
...  
Keyword(s):  
Thin Films ◽  
Secondary Phase ◽  
Hexagonal Wurtzite Structure ◽  
Zno Thin Films ◽  
Spray Pyrolysis Method ◽  
Efficient Energy Transfer ◽  
Force Microscopy ◽  
Co Doping ◽  
Glass Substrates ◽  
Hall Effect Measurements

Structural, optical and electrical properties of (ytterbium/terbium) co-doped ZnO thin films deposited on glass substrates using the spray pyrolysis method were investigated. The films exhibited the hexagonal wurtzite structure with a preferential orientation along (002) direction. No secondary phase was observed in the X-ray diffraction detection limit. Atomic force microscopy (AFM) was performed and root means square roughness (RMS) of our samples decreased with terbium content. Photoluminescence measurements showed a luminescence band at 980 nm which is characteristic of Yb3+ transition between the electronic levels 2F5/2 to 2F7/2. This is experimental evidence for an efficient energy transfer from the ZnO matrix to Yb. Hall Effect measurements gave a low electrical resistivity value around 6.0 × 10−3 Ω.cm. Such characteristics make these films of interest to photovoltaic devices.

Sign in / Sign up

Export Citation Format

Share Document