scholarly journals Effect of Metakaolin on Strength and Efflorescence Quantity of Cement-Based Composites

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Tsai-Lung Weng ◽  
Wei-Ting Lin ◽  
An Cheng
Keyword(s):  
Compressive Strength ◽  
Image Analysis ◽  
Portland Cement ◽  
Detrimental Effect ◽  
Cement Mortar ◽  
Hydration Products ◽  
X Ray Diffraction ◽  
Replacement Ratio ◽  
X Ray ◽  
Scanning Electron

This study investigated the basic mechanical and microscopic properties of cement produced with metakaolin and quantified the production of residual white efflorescence. Cement mortar was produced at various replacement ratios of metakaolin (0, 5, 10, 15, 20, and 25% by weight of cement) and exposed to various environments. Compressive strength and efflorescence quantify (using Matrix Laboratory image analysis and the curettage method), scanning electron microscopy, and X-ray diffraction analysis were reported in this study. Specimens with metakaolin as a replacement for Portland cement present higher compressive strength and greater resistance to efflorescence; however, the addition of more than 20% metakaolin has a detrimental effect on strength and efflorescence. This may be explained by the microstructure and hydration products. The quantity of efflorescence determined using MATLAB image analysis is close to the result obtained using the curettage method. The results demonstrate the best effectiveness of replacing Portland cement with metakaolin at a 15% replacement ratio by weight.

scholarly journals Compressive strength and microstructure of modified coffee exocarp cement-based composites

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 9059-9074
Author(s):  
Zehua Zhu ◽  
Cheng Cheng ◽  
Debin Zhu ◽  
Dewen Liu ◽  
Yafei Zhang
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Portland Cement ◽  
Vacuum Extraction ◽  
X Ray Diffraction ◽  
Extraction Technology ◽  
X Ray ◽  
Scanning Electron

Portland cement-based composites were prepared with coffee exocarp (pretreated with water or NaOH) via vacuum extraction technology. An orthogonal test was adopted to analyze the influence of various factors on mechanical properties of the composite. The morphology and composition of the pretreated coffee exocarp and composites were analyzed via environmental scanning electron microscopy and X-ray diffraction, respectively. The results showed that the coffee exocarp content and vacuum extraction time significantly affected the compressive strength. An addition of 10% coffee exocarp had a slight negative effect on the mechanical properties but enhanced the crack inhibition and overall toughness of the composite. The scanning electron microscopy and X-ray diffraction results showed that the composite containing coffee exocarp pretreated with 4% NaOH solution had the highest density and exhibited the best properties due to mechanical interlocking between the coffee exocarp and cement. After 28 d of curing, the composites exhibited a maximum compressive strength of 15.72 MPa, a mass that was approximately 37% less than that of ordinary Portland cement samples, and a bulk density of 1.5 g/cm3 to 1.6 g/cm3. Hence, the produced biocomposites could be used for low-load pavements, providing a new type of economical building material.

Utilization of Desulfuration Residues in Non-Autoclaved Aerated Concrete

2011 ◽  
Vol 250-253 ◽  
pp. 707-710
Author(s):  
Fang Xian Li ◽  
You Zhi Chen ◽  
Qi Jun Yu ◽  
Jiang Xiong Wei
Keyword(s):  
Compressive Strength ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Bulk Density ◽  
Hydration Products ◽  
X Ray Diffraction ◽  
X Ray ◽  
Autoclaved Aerated Concrete ◽  
Aerated Concrete ◽  
Scanning Electron

Desulfuration residues were used as aggregate to produce Non-autoclaved aerated concrete. The effects of water-hinder ratio, casting temperature on the gas forming behavior, and those of desulfuration residue content on the compressive strength and bulk density of aerated concrete were investigated. The types of the hydration products and the microstructure of Non-autoclaved aerated concrete with desulfuration residue were investigated by means of X-ray diffraction and scanning electron microscope. Results show that the optimum replacement amount was determined as 50% and at this rate the compressive strength, bulk density of Non-autoclaved aerated concrete were measured as 2.83 MPa and 543 kg/m3. The hydration products of Non-autoclaved aerated concrete with desulfuration residue are C2SH (A) and C2SH (B) along with ettringite and hydrogarnet phases.

Effect of Curing Time on the Pore Structure of the Portland Cement Concrete

2010 ◽  
Vol 44-47 ◽  
pp. 2592-2596
Author(s):  
Wei Lun Wang ◽  
Peng Liu
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Pore Structure ◽  
Mercury Intrusion Porosimetry ◽  
Curing Time ◽  
Hydration Products ◽  
Portland Cement Concrete ◽  
X Ray Diffraction ◽  
Cement Concrete ◽  
X Ray

In this paper, the influence of curing time on the compressive strength and pore structure of the Portland cement concrete was investigated. The phase composition and morphology of hydration products of Portland cement were analyzed with X-ray diffraction (XRD). In addition, the porosity and pore distribution of the concrete were also researched using mercury intrusion porosimetry (MIP), surface area and porosity analyzer (BET). The results show that the influence of curing time on the compressive strength and pore structure of the concrete is obvious. With curing time increasing, the compressive strength of the concrete increased and the porosity decreased. The corresponding fractal dimension of the pore and the microstructure were changed, as well. With time increasing, more hydration products were produced.

Effect of P2O5 on the Properties of Alite-Calcium Strontium Sulphoaluminate Cement

2011 ◽  
Vol 306-307 ◽  
pp. 961-965
Author(s):  
Chao Nan Yin ◽  
Ling Chao Lu ◽  
Shou De Wang
Keyword(s):  
Compressive Strength ◽  
Electron Microscope ◽  
Heat Evolution ◽  
Petrographic Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sulphoaluminate Cement ◽  
Suitable Amount ◽  
Acceleration Period ◽  
Scanning Electron

The influence of P2O5on the properties of alite-calcium strontium sulphoaluminate cement was researched by means of X-ray diffraction, scanning electron microscope-energy dispersive spectroscopy (SEM-EDS) and petrographic analysis. The results show that the optimal content of P2O5is 0.3% and the compressive strength of the cement at 1, 3, 28d are 27.0, 59.1, 110.9MPa when the calcining temperature is 1350°C. P2O5mainly exists in the belite and a suitable amount of P2O5can promote the formation of C1.5Sr2.5A3and alite. When the content of P2O5is higher than 0.3%, the formation of C1.5Sr2.5A3and alite can be hindered. P2O5can enhance the hydration heat evolution rate in the acceleration period and the hydrate heat of cement containing P2O5increases slightly.

scholarly journals Defects of copper patina / Vady mìdìných patin

2015 ◽  
Vol 59 (3) ◽  
pp. 87-90 ◽  
Author(s):  
J. Stoulil ◽  
P. Šedá ◽  
M. Anisová ◽  
Z. Fencl ◽  
P. Novák ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Image Analysis ◽  
Compact Surface ◽  
Historical Buildings ◽  
X Ray Diffraction ◽  
X Ray ◽  
Destructive Analysis ◽  
High Degree ◽  
Scanning Electron

Abstract The paper is focused on analyses of dark copper patina defects that were formed on one sheet under the same conditions. Roofs of ten historical buildings were studied by image analysis and samples of two roofs were subjected to more detailed destructive analysis. These samples were studied by means of scanning electron microscopy with energy dispersive X-ray spectroscopy, X-ray diffraction and infrared spectroscopy. Both types of patina are composed of brochantite. Green patinas consisted of a pure brochantite and they had a fl at and compact surface. Conversely, black patina contained a high degree of impurities (ammonia cations, nitrates, silicates) and the surface was rough. The proportion of dark patina was higher in south and east facing surfaces, where washing by rainfall is more difficult.

UTILIZATION OF FLY ASH AND CONCRETE RESIDUE IN THE PRODUCTION OF GEOPOLYMER BRICKS

2017 ◽  
Vol 12 (1) ◽  
pp. 63-77 ◽  
Author(s):  
Siriporn Sirikingkaew ◽  
Nuta Supakata
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Phase Composition ◽  
Fly Ash ◽  
Industrial Waste ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

This study presents the development of geopolymer bricks synthetized from industrial waste, including fly ash mixed with concrete residue containing aluminosilicate compound. The above two ingredients are mixed according to five ratios: 100:0, 95:5, 90:10, 85:15, and 80:20. The mixture's physico-mechanical properties, in terms of water absorption and the compressive strength of the geopolymer bricks, are investigated according to the TIS 168-2546 standard. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses are used to investigate the microstructure and the elemental and phase composition of the brick specimens. The results indicate that the combination of fly ash and concrete residue represents a suitable approach to brick production, as required by the TIS 168–2546 standard.

scholarly journals Industrial Waste Utilization of Carbon Dust in Sustainable Cementitious Composites Production

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3295
Author(s):  
Mohammad R. Irshidat ◽  
Nasser Al-Nuaimi
Keyword(s):  
Compressive Strength ◽  
Industrial Waste ◽  
Cement Mortar ◽  
Waste Utilization ◽  
Cementitious Composites ◽  
X Ray Diffraction ◽  
Sem Images ◽  
Compact Structure ◽  
X Ray ◽  
Industrial Waste Utilization

This paper experimentally investigates the effect of utilization of carbon dust generated as an industrial waste from aluminum factories in cementitious composites production. Carbon dust is collected, characterized, and then used to partially replace cement particles in cement mortar production. The effect of adding different dosages of carbon dust in the range of 5% to 40% by weight of cement on compressive strength, microstructure, and chemical composition of cement mortar is investigated. Scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray fluorescence (XRF) analysis are used to justify the results. Experimental results show that incorporation of carbon dust in cement mortar production not only reduces its environmental side effects but also enhances the strength of cementitious composites. Up to 10% carbon dust by weight of cement can be added to the mixture without adversely affecting the strength of the mortar. Any further addition of carbon dust would decrease the strength. Best enhancement in compressive strength (27%) is achieved in the case of using 5% replacement ratio. SEM images show that incorporation of small amount of carbon dust (less than 10%) lead to produce denser and more compact-structure cement mortar.

scholarly journals Valorization of Brick and Glass CDWs for the Development of Geopolymers Containing More Than 80% of Wastes

Minerals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 672
Author(s):  
Dimitris Kioupis ◽  
Aggeliki Skaropoulou ◽  
Sotirios Tsivilis ◽  
Glikeria Kakali
Keyword(s):  
Electron Microscopy ◽  
Compressive Strength ◽  
Circular Economy ◽  
X Ray Diffraction ◽  
Glass Waste ◽  
X Ray ◽  
Optimum Synthesis ◽  
Synthesis Parameters ◽  
Construction And Demolition Wastes ◽  
Scanning Electron

One of the areas of priority in a circular economy, regarding waste management, regards the valorization of construction and demolition wastes (CDW). This study suggests the synthesis of geopolymeric binders based almost entirely on construction and demolition wastes. Ceramic waste was used as the aluminosilicate precursor of the geopolymer synthesis, while glass waste was applied in the preparation of the activation solution. A fractional experimental design defined the optimum synthesis parameters, based on compressive strength values. The final products were characterized by means of X-Ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The glass waste was appropriately processed in order to prepare the activation solution for the geopolymerization of brick waste. In this work, CDW-based geopolymers were produced with a compressive strength in the range 10–44 MPa. The developed products contained 80–90 wt.% CDWs, depending on the method of activator preparation.

Effect of Chemical Composition on the Properties of Reconstructed Steel Slag

2019 ◽  
Vol 944 ◽  
pp. 1163-1171
Author(s):  
Ying Xu ◽  
Qiao Ling Wang ◽  
Chen Guang Hu ◽  
Shan Shan Yang
Keyword(s):  
Compressive Strength ◽  
Steel Slag ◽  
Temperature Reconstruction ◽  
X Ray Diffraction ◽  
Technological Parameters ◽  
Iron And Steel ◽  
X Ray ◽  
Volume Stability ◽  
Cementitious Activity ◽  
Scanning Electron

The steel slag is not widely or extensively used because of its poor volume stability and low cementitious activity. In this paper, the solid waste fly ash, quicklime and slag discharged from iron and steel enterprises are used as conditioning components in the experiment. In order to improve the cementitious activity and volume stability of steel slag, the high temperature reconstruction experiment of steel slag was completed. The effects of C/S (2.50~3.14), S/A (4.5~17. 81) on the cementitious activity and volume stability of reconstructed steel slag were investigated by means of the tests of compressive strength, scanning electron microscope, X-ray diffraction, lithofacies test, stability test and so on. The results showed that the cementitious activity and volume stability of the reconstructed steel slag were improved in the higher C/S or lower S/A. The cementitious activity and volume stability of the reconstructed steel slag were improved with the increase of CaF2 content. By analyzing the cementitious activity and volume stability of the reconstructed steel slag, the optimum technological parameters are obtained as follows: C/S is 2.70 , S/A is 5.78, the content of CaF2 is 4%.

scholarly journals Different Setting Conditions Affect Surface Characteristics and Microhardness of Calcium Silicate-Based Sealers

Scanning ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Dong-Kyu Yang ◽  
Sunil Kim ◽  
Jeong-Won Park ◽  
Euiseong Kim ◽  
Su-Jung Shin
Keyword(s):  
Calcium Silicate ◽  
Detrimental Effect ◽  
Surface Characteristics ◽  
Storage Conditions ◽  
Acid Solutions ◽  
X Ray Diffraction ◽  
Surface Microhardness ◽  
X Ray ◽  
Phosphate Buffered Saline ◽  
Scanning Electron

Objective. To investigate the effect of different setting conditions on surface microhardness and setting properties of calcium silicate-based sealers. Methods. Three sealers, EndoSequence Bioceramic (BC; Brasseler USA, Savannah, GA, USA), Endoseal MTA (ES; Maruchi, Wonju, Korea), and Well-Root ST (WR; Vericom, Chuncheon, Korea), were compared. Specimens were exposed to either butyric acid (pH 5.4) or phosphate-buffered saline (PBS [pH 7.4]) for 48 h and stored at 100% humidity for 12 days. The control specimens were stored at 100% humidity for 14 days. Surface microhardness was measured, topographic changes were observed, and phase analysis was performed using X-ray diffraction. Microhardness according to storage conditions was compared using one-way analysis of variance and Tukey’s multiple comparison tests (P<.05). Results. The BC and ES sealers exhibited decreased microhardness when stored in acid or PBS compared with control (P<.05). In the WR group, acid exposure lowered microhardness of the specimens compared with control (P<.05). Scanning electron microscopy revealed different topographies in specimens from all tested sealers exposed to acid or PBS. Conclusion. The surface microhardness of calcium silicate-based sealers was reduced by exposure to either acid or PBS. Acid solutions, however, had a more detrimental effect than PBS.

Sign in / Sign up

Export Citation Format

Share Document